Related Manuals for rtd LAN10255HR
Summary of Contents for rtd LAN10255HR
- Page 1 LAN10255HR LAN16255HR LAN17255HR LAN18255HR 5-Port Gigabit Ethernet Unmanaged Switch User’s Manual BDM-610020107 Rev. C RTD Embedded Technologies, Inc. AS9100 and ISO 9001 Certified...
- Page 2 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com...
-
Page 3: Revision History
Failure to follow the instructions found in this manual may result in damage to the product described in this manual, or other components of the system. The procedure set forth in this manual shall only be performed by persons qualified to service electronic equipment. Contents and specifications within this manual are given without warranty, and are subject to change without notice. RTD Embedded Technologies, Inc. shall not be liable for errors or omissions in this manual, or for any loss, damage, or injury in connection with the use of this manual. -
Page 4: Table Of Contents
IDAN Connector Location ................................. 16 IDAN-LAN17255HR .................................. 16 IDAN Twisted Pair Ethernet PORT1, PORT2, PORT3, PORT4, and PORT5 ................. 17 Steps for Installing ..................................17 Troubleshooting Additional Information PC/104 Specifications ................................19 Limited Warranty | www.rtd.com LAN17255HR User’s Manual RTD Embedded Technologies, Inc. - Page 5 Table 5: DIL Signal Assignments .................................... 11 Table 6: Status LEDs ......................................11 Table 7: CN14 External LED Drive ..................................12 Table 8: CN17 Power Connector .................................... 12 Table 9: LAN17255HR IDAN Pin Out ..................................17 | www.rtd.com LAN17255HR User’s Manual RTD Embedded Technologies, Inc.
-
Page 6: Introduction
The Intelligent Data Acquisition Node (IDAN™) building block can be used in just about any combination with other IDAN building blocks to create a simple but rugged 104™ stack. This module can also be incorporated in a custom-built RTD HiDAN™ or HiDANplus High Reliability Intelligent Data Acquisition Node. -
Page 7: Contact Information
If you are having problems with you system, please try the steps in the Troubleshooting section of this manual. For help with this product, or any other product made by RTD, you can contact RTD Embedded Technologies technical support via the... -
Page 8: Specifications
+125 Relative Humidity Non-Condensing MTBF Mean Time Before Failure Hours Electrical Characteristics Table 3: Electrical Characteristics Symbol Parameter Test Condition Unit Power Consumption = 5.0V 1.25 5V Input Supply Current Active | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 9: Board Connection
Physical Characteristics Weight: Approximately 55 g (0.12 lbs.) Dimensions: 90.17 mm L x 95.89 mm W (3.550 in L x 3.775 in W) Figure 1: Board Dimensions | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 10: Connectors And Jumpers
Connectors CN5, CN7, CN9, CN11, and CN16 are for UTP (Unshielded Twisted Pair) wiring normally used for 10/100/1000 Base-T Ethernet. It is the default factory installed twisted pair connector on the board. The following table gives the pin out of CN5, CN7, CN9, CN11, and CN16. | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 11: Twisted Pair Ethernet Cn4, Cn6, Cn8, Cn10, And Cn13
3.3 volts or ground to use with these signals. These connectors are not installed when the Ethernet RJ45 connectors and LEDs are installed. The pin out is in the table below. | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 12: Cn17 Power Connector
The PCI connector is the connection to PCI peripheral modules. This connector is used only as a +5V and ground source. The position and pin assignments are compliant with the PC/104-Plus Specification. (See PC/104 Specifications on page 19). | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 13: Steps For Installing
10. Attach any necessary cables to the PC/104 stack. 11. Re-connect the power cord and apply power to the stack. 12. Boot the system and verify that all of the hardware is working properly. Figure 4: Example 104™Stack | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 14: Functional Description
LED circuitry. These signals can source or sink 24 mA and the board has a jumper option for 3.3 volt or ground to facilitate external LED configuration. | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 15: Idan Connections
Weight: Approximately 0.21 Kg (0.46 lbs.) Dimensions: 151.972 mm L x 129.978 mm W x 16.993 mm H (5.983 in L x 5.117 in W x 0.669 in H) Figure 6: IDAN Dimensions | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 16: Idan Connector Location
Figure 7: IDAN Connector Location IDAN-LAN17255HR This utilityModule is also available in an IDAN configuration. The IDAN module is shown below. Figure 8: IDAN-LAN17255HR Front View Figure 9: IDAN-LAN17255HR Rear View | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 17: Idan Twisted Pair Ethernet Port1, Port2, Port3, Port4, And Port5
10. Attach any necessary cables to the IDAN system. 11. Re-connect the power cord and apply power to the stack. 12. Boot the system and verify that all of the hardware is working properly. Figure 10: Example IDAN System | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 18: Troubleshooting
If problems persist, or you have questions about configuring this product, contact RTD Embedded Technologies via the following methods: Phone: +1-814-234-8087 E-Mail: techsupport@rtd.com Be sure to check the RTD web site (http://www.rtd.com) frequently for product updates, including newer versions of the board manual and application software. | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 19: Additional Information
Additional Information PC/104 Specifications A copy of the latest PC/104 specifications can be found on the webpage for the PC/104 Consortium: www.pc104.org | www.rtd.com LAN17255HRHR User’s Manual RTD Embedded Technologies, Inc. -
Page 20: Limited Warranty
During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any defective products or parts at no additional charge, provided that the product is returned, shipping prepaid, to RTD Embedded Technologies. All replaced parts and products become the property of RTD Embedded Technologies. - Page 21 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com Copyright 2013 by RTD Embedded Technologies, Inc. All rights reserved.
Need help?
Do you have a question about the LAN10255HR and is the answer not in the manual?
Questions and answers