Related Manuals for rtd IDAN-ID5915
Summary of Contents for rtd IDAN-ID5915
- Page 1 IDAN-ID5915 Cisco® 5915 Embedded Services Router for IDAN User’s Manual IDM-650020046 Rev. C RTD Embedded Technologies, Inc. AS9100 and ISO 9001 Certified...
- Page 2 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com...
- Page 3 Failure to follow the instructions found in this manual may result in damage to the product described in this manual, or other components of the system. The procedure set forth in this manual shall only be performed by persons qualified to service electronic equipment. Contents and specifications within this manual are given without warranty, and are subject to change without notice. RTD Embedded Technologies, Inc. shall not be liable for errors or omissions in this manual, or for any loss, damage, or injury in connection with the use of this manual.
-
Page 4: Table Of Contents
Setting a Password ................................... 22 Enabling the CLR Button ................................23 Restoring Default Settings via CLI ............................23 Cisco Software Updates ................................24 Network Security Considerations .............................. 24 Troubleshooting Additional Information PC/104 Specifications ................................26 | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. - Page 5 Cisco 5915 Embedded Services Router Hardware Technical Guide ..................26 Software Configuration Guide for Cisco IOS ..........................26 Cisco Guide to Harden Cisco IOS Devices ..........................26 Cisco Router Configuration Handbook ............................. 26 Limited Warranty | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc.
- Page 6 Figure 7: RJ-45 Connector ..................................... 13 Figure 8: Console Connector ....................................13 Figure 9: Example IDAN System .................................... 16 Figure 10: IDAN-ID5915 Block Diagram ................................. 17 Figure 11: Serial Console Typical Boot Messages ..............................18 Figure 12: Serial Console Default Command Prompt ............................19 Figure 13: Serial Console After Pressing CLR ...............................
-
Page 7: Introduction
Product Overview The IDAN-ID5915 incorporates the Cisco 5915 Embedded Services Router into RTD’s standard IDAN packaging technology. It provides all necessary connections to interface with the board-level router product. The router may be operated standalone with a power supply, or stacked with RTD’s cpuModules and other peripherals using the PCI/104-Express stackable bus structure. -
Page 8: Ordering Information
) building block can be used in just about any combination with other IDAN building blocks to ® create a simple but rugged 104™ stack. This module can also be incorporated into a tailored RTD HiDAN or HiDANplus High Reliability ®... -
Page 9: Contact Information
If you are having problems with your system, please try the steps in the Troubleshooting chapter of this manual. For help with this product, or any other product made by RTD, you can contact RTD Embedded Technologies technical support via the following methods:... -
Page 10: Specifications
Total Power Consumption = 5.0V 10.19 5V Input Supply Current Active 1120 2038 Inrush 2121 PCI 3.3V Output Voltage 3.14 3.47 OUT3 PCI 3.3V Output Current OUT3 Table 3: Electrical Characteristics | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 11: Idan Connections
Dimensions: 152 mm L x 130 mm W x 35 mm H (5.983 in L x 5.117 in W x 1.388 in H) Figure 3: Exterior Dimensions for IDAN-ID5915D (Not to Scale) | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 12: Connectors
Figure 4: Exterior Dimensions for IDAN-ID5915U (Not to Scale) Connectors 3.3.1 I/O C XTERNAL ONNECTORS 3.3.1.1 Front Panel Connector Locations Figure 5: Front Panel Connector Locations for IDAN-ID5915D (Not to Scale) | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 13: Fast Ethernet Ports (Fe0/0, Fe0/1, Fe0/3, And Fe0/4)
The Serial Console port is a standard female 9-pin D-SUB connector. The figure below shows the pin numbers when looking into the connector. Figure 8: Console Connector The Serial Console signaling level is RS-232, and it follows the standard RS-232 device pinout. The following table gives the pinout. | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 14: Internal Connectors
PCI slot. The PCI bus is used for power only. The LAN25E5915 board in the IDAN slice includes a voltage regulator to provide +5V and +3.3V the Cisco 5915 board requires. If powering the IDAN-ID5915 from the PCI bus, only +5V should be connected. -
Page 15: Cn4(Top) & Cn7(Bottom): Fe0/2 Stacknet Tm Connector
CN4(Top) & CN7(Bottom): FE0/2 StackNET Connector CN4/CN7 is a board-to-board Fast Ethernet connection which allows the IDAN-ID5915 to be stacked with other RTD StackNET products, such as Ethernet switches. Either CN4 or CN7 will be populated, depending on whether an upward or downward stacking configuration was ordered. -
Page 16: Steps For Installing
10. Attach any necessary cables to the IDAN system. 11. Re-connect the power cord and apply power to the stack. 12. Boot the system and verify that all of the hardware is working properly. Figure 9: Example IDAN System | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 17: Functional Description
Refer to the Software Configuration chapter later in this manual for details. Switched Ethernet Ports (FE0/2, FE0/3, & FE0/4) The switched ports are traditionally used for the LAN interface of the system. FE0/2 is used internally in the IDAN system for the RTD StackNET interface. -
Page 18: Console Port
The serial console port is primarily used for initial router configuration and troubleshooting. In Cisco IOS, it is identified as con0. The Console port may be connected to the RS-232 serial port on an RTD cpuModule, laptop, or a desktop PC. If the computer does not have a serial port available, a USB to RS-232 serial adapter may be used. -
Page 19: Status Leds
Ethernet interfaces will be disabled, and the router will hang. To use the router again, it must be power cycled, and the configuration and/or Cisco IOS image must be reloaded. | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 20: Figure 13: Serial Console After Pressing Clr
Figure 13: Serial Console After Pressing CLR | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 21: Software Overview
The router must be configured properly before it may be used on the network. It is not a “plug and play” device, nor does it have a “simple” GUI configuration wizard. To use the IDAN-ID5915, it is assumed that one is already somewhat familiar with the Cisco IOS CLI and network engineering concepts. -
Page 22: Configuration Basics
The following screenshot demonstrates a basic method to set passwords. In the example below, both local serial console and network terminals have a password of MustBeChanged set, while the enable command is protected with the password EnableMe. | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 23: Enabling The Clr Button
To erase the startup configuration via the command-line interface, run the privileged EXEC command delete nvram:startup-config, followed by the reload command. When prompted for confirmation, press Enter. The router will reboot. Once the router is booted, it will be using the factory defaults. | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. -
Page 24: Cisco Software Updates
Cisco Software Updates The IDAN-ID5915 includes one year of technical support and software updates from Cisco for the 5915 Embedded Services Router. Software updates for the 5915 ESR may be downloaded from Cisco, as long as a valid support agreement is in place. Visit http://support.cisco.com... -
Page 25: Troubleshooting
If problems persist, or you have questions about using the product, the following support options are available: • For questions regarding the router enclosure, the interface boards, and basic troubleshooting, contact RTD’s Technical support via the following methods: Phone:... -
Page 26: Additional Information
Recommendations on how to secure a Cisco IOS device: http://www.cisco.com/c/en/us/support/docs/ip/access-lists/13608-21.html Cisco Router Configuration Handbook A book that provides an introduction to configuring a Cisco IOS router, plus network routing protocols and concepts. ISBN-13: 061-9472141168 ISBN-10: 1587141167 | www.rtd.com IDAN-ID5915 User’s Manual RTD Embedded Technologies, Inc. - Page 27 During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any defective products or parts at no additional charge, provided that the product is returned, shipping prepaid, to RTD Embedded Technologies. All replaced parts and products become the property of RTD Embedded Technologies.
- Page 28 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com Copyright 2018 by RTD Embedded Technologies, Inc. All rights reserved.
Need help?
Do you have a question about the IDAN-ID5915 and is the answer not in the manual?
Questions and answers