Related Manuals for Accton Technology Edge-Core OD200
Summary of Contents for Accton Technology Edge-Core OD200
- Page 1 Powered by Accton OD200 User Guide Outdoor WiMAX Residential Gateway www.edge-core.com...
- Page 3 User Guide OD200 Outdoor IEEE 802.16e-2005 Mobile WiMAX Unit, with 2.3/2.5/3.5 GHz Frequency Band Support and Integrated Antenna, and Indoor Gateway Unit, with Four LAN (RJ-45) Ports, Two VoIP (RJ-11) Ports, and 802.11g Wi-Fi...
- Page 4 OD200 E032008-CS-R01 1*************...
-
Page 5: Federal Communication Commission Interference Statement
Compliances Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 6 EC Conformance Declaration Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: • EN 60950-1 (IEC 60950-1) - Product Safety • EN 301 489-1, EN 301 489-4 - EMC requirements for radio equipment •...
-
Page 7: About This Guide
About This Guide Purpose This guide details the hardware features of the WiMAX Residential Gateway including its physical and performance-related characteristics, and how to install the device and use its configuration software. Audience This guide is for PC users with a working knowledge of computers. You should be familiar with basic networking concepts. -
Page 9: Table Of Contents
Wi-Fi Status Indicator LED 10BASE-T/100BASE-TX LAN Ports ODU Port VoIP Phone Ports Power Adapter Socket Backup Battery Charger (Optional) SIM Card Slot Chapter 2: Installing the OD200 Package Checklist Installation Overview ODU Installation ODU Location Mount the Unit IDU Installation... - Page 10 Table of Contents The Advanced Setup Menu 3-12 Chapter 4: System Settings Host Name System Time Administrator Settings Firmware Update Configuration Tools System Status System Log Reset Chapter 5: Gateway Configuration WAN Settings Dynamic IP Address Static IP Settings L2TP Settings PPPoE Settings LAN Settings DHCP Client List...
- Page 11 Table of Contents SIP Setting Dial Plan Call Feature Codecs Call Block Setting Phone Setting 7-10 Chapter 8: Wi-Fi Settings Wireless Settings Wireless Security WEP Shared Key Security WPA/WPA2 Security WPA/WPA2 PSK Security MAC Authentication Appendix A: Troubleshooting Diagnosing LED Indicators Cannot Connect to the Internet Cannot Access Web Management Forgot or Lost the Password...
- Page 12 Table of Contents Glossary Index viii...
- Page 13 Tables Table 1-1 OD200 Models Table 1-2 SAU LED Indicators Table 1-3 Power Status LED Table 1-4 Wi-Fi Status LED Table 1-5 LAN Port Status LEDs Table 4-1 System Settings Table 5-1 Gateway Configuration Table 6-1 WiMAX Settings Table 8-1 Wi-Fi Settings Table A-1 Troubleshooting Chart Table C-1.
- Page 14 Figures Figure 1-1 ODU Components Figure 1-2 SAU LED Indicators Figure 1-3 Front of the IDU Figure 1-4 Base of the IDU Figure 1-5 Back of the IDU Figure 1-6 IDU LED Indicators Figure 1-7 SIM Card Slot Access Figure 2-1 ODU Antenna Polarization Figure 2-2 Securing the ODU to the Pole...
- Page 15 Figures Figure 5-3 Static IP Settings Figure 5-4 L2TP Settings Figure 5-5 PPPoE Settings Figure 5-6 DNS Settings Figure 5-7 LAN Settings Figure 5-8 DHCP Client List Figure 5-9 Virtual Server Figure 5-10 Port Mapping 5-10 Figure 5-11 DMZ Settings 5-11 Figure 5-12 Firewall Setting...
- Page 16 Figures...
-
Page 17: Chapter 1: Introduction
DSL or cable modems. The OD200 is a combination of an indoor unit (IDU) and an outdoor unit (ODU). There are different ODU units for each of the 2.3, 2.5, and 3.5 GHz WiMAX frequency bands. -
Page 18: Odu Hardware Description
Introduction ODU Hardware Description The ODU is a weatherproof unit that is pole mounted outdoors. It includes a built-in antenna for WiMAX communications, as well as a connector for an optional external antenna. The unit includes an RJ-45 Ethernet port for a connection to the IDU. Built-in Antenna SAU Port Ground Screw... -
Page 19: Weatherproof Port Covers
ODU Hardware Description Weatherproof Port Covers The ODU includes rubber weatherproof port covers for the RJ-45 and SAU ports. The RJ-45 port cover allows the Ethernet cable to be fed through and conneted to the RJ-45 port. The SAU port cover protects the SAU port when it is not in use. Ground Screw Even though the ODU includes its own built-in lightning protection, it is important that the unit is properly connected to ground. -
Page 20: Table 1-2 Sau Led Indicators
Introduction Table 1-2 SAU LED Indicators Status Description AL (Alarm) The diagnostic test has passed and the ODU is operating normally. On Red An ODU failure has been detected. PW (Power) The ODU is not receiving power or there is an internal 3.3 VDC failure. -
Page 21: Idu Hardware Description
IDU Hardware Description IDU Hardware Description The front of the IDU provides an array of system status indicators. The back includes four LAN ports for 10/100 Mbps Ethernet connections, two RJ-11 Voice over IP (VoIP) phone ports, and a DC power jack. One additional RJ-45 port is for connection to the ODU, providing both a data link and power to the ODU unit. -
Page 22: Wi-Fi Antenna
Introduction DC IN LAN 1 LAN 2 LAN 3 LAN 4 PHONE 1 PHONE 2 10-19V RJ-45 LAN Ports RJ-45 ODU Port VoIP Phone Ports Power Socket (include Link/Activity LEDs) Figure 1-5 Back of the IDU Wi-Fi Antenna The IDU includes 802.11b/g Wi-Fi. There is a single 2.4 GHz antenna included for local wireless connections to PCs. -
Page 23: Wi-Fi Status Indicator Led
IDU Hardware Description Power Status LED Power WiFi Wi-Fi Status LED Figure 1-6 IDU LED Indicators Table 1-3 Power Status LED Status Description On Green The unit has a network association with a WiMAX base station. Flashing Green Indicates one of the following conditions: •... -
Page 24: 10Base-T/100Base-Tx Lan Ports
AC supply fails. The backup battery charger holds 10 rechargable AA-type batteries. The batteries are charged while the AC power adapter is powering the OD200 units. If the AC power fails, the batteries can power the OD200 for up to five hours. -
Page 25: Sim Card Slot
IDU Hardware Description SIM Card Slot The IDU also includes a standard SIM card slot that can be accessed by removing the unit’s top cover. Some WiMAX service providers may require an optional SIM Card to be installed in the IDU. The SIM card can include all required configuration details, including security set up, operator information, and other end-user specific parameters. - Page 26 Introduction 1-10...
-
Page 27: Chapter 2: Installing The Od200
• Software Utilities and User Guide CD Installation Overview Before installing the OD200, verify that you have all the items listed in the package checklist above. If any of the items are missing or damaged, contact your local dealer. Also, be sure you have all the necessary tools and cabling before installing the OD200. -
Page 28: Odu Installation
Installing the OD200 ODU Installation The ODU includes its own bracket kit for mounting the unit to a 1 to 4 inch diameter steel pole or tube. The pole-mounting bracket allows the unit to be mounted to part of a radio mast or tower structure. -
Page 29: Figure 2-1 Odu Antenna Polarization
ODU Installation Polarization Arrow Attach the two threaded bolts to the ODU using a flat screwdriver Vertical Polarization Polarization Arrow Horizontal Polarization Figure 2-1 ODU Antenna Polarization Place the ODU against one side of the pole and then fit the bracket onto the threaded bolts. -
Page 30: Idu Installation
To connect the IDU, follow these steps: Power on the IDU by connecting the AC power adapter and plugging it into an AC power source. Use ONLY the power adapter supplied with the OD200. Otherwise, the Caution: product may be damaged. -
Page 31: Figure 2-3 Idu Connections
IDU Installation Connect Category 5 or better Ethernet cables from the IDU’s LAN ports to the network ports of your PCs. Alternatively, you can connect the LAN ports to an Ethernet switch or other devices. Make sure the length of each cable does not exceed 100 meters (328 ft). -
Page 32: Odu Cable Connections
Installing the OD200 ODU Cable Connections The ODU needs to be connected to the IDU using Ethernet cable, and the ODU must be grounded by connecting a grounding wire. ODU-IDU Ethernet Cable Connection Use outdoor-rated Category 5E or better Ethernet cable with RJ-45 connectors on each end. -
Page 33: Figure 2-5 Idu Com Port Connection
ODU Cable Connections Figure 2-5 IDU COM Port Connection Seal the IDU COM connector using tar seal or weatherproof tape to protect against rain and moisture. Route the Ethernet cable from the ODU to the IDU following your cable plan and connect it to the ODU port on the IDU (see Figure 1-5). -
Page 34: Odu Antenna Alignment
Installing the OD200 Connect the other end of the grounding wire to a good ground (earth) connection. Note: Use cable strips to secure all cables to the pole. Figure 2-7 Grounding Wire Connection ODU Antenna Alignment The ODU will provide the best link quality when its antenna is aligned in the direction of the WiMAX base station. -
Page 35: Figure 2-9 Sealed Odu Connectors
ODU Antenna Alignment Note: If all the SAU link quality LEDs are on, including LED 9 (red), the received signal strength is too high. Move the ODU’s position so that only LEDs 1 to 8 are on. Remove the SAU connection and replace the rubber sealing cover on the port. Seal the SAU connector using tar seal or weatherproof tape to protect against rain and moisture. - Page 36 Installing the OD200 2-10...
-
Page 37: Chapter 3: Initial Configuration
Setup Wizard or Advanced Setup options. Accessing the Web Management Interface The OD200 has a default IP address of 192.168.1.1 and a subnet mask of 255.255.255.0. If your PC is set to have an IP address assigned by DHCP (Dynamic Host Configuration Protocol), you can connect immediately to the web management interface. -
Page 38: Figure 3-2 Home Page
Initial Configuration Figure 3-2 Home Page To configure basic settings for the current operating mode, click Setup Wizard. For more information, see “Initial Configuration” on page 3-1. Alternatively, to configure more detailed settings, click Advanced Setup. For more information, see “The Advanced Setup Menu” on page 3-12. Note: It is recommended that you configure a user password as the first step under unit “Administrator Settings”... -
Page 39: Using The Setup Wizard
Using the Setup Wizard Using the Setup Wizard The Setup Wizard takes you through the basic configuration steps for the current operating mode. Launching the Setup Wizard – To perform basic configuration, click Setup Wizard on the home page. When configuring the unit through the Setup Wizard you will need to proceed through the following steps: Host Settings –... -
Page 40: Figure 3-4 Time Zone
Initial Configuration Time Zone – The time zone for the country in which the unit is being used, expressed in GMT format. Figure 3-4 Time Zone Set Time Zone – Selects the time zone in which the unit is being used. -
Page 41: Figure 3-5 Wan Type
Using the Setup Wizard WAN Settings – The WAN Settings page is for specifying the type of connection to your Internet service provider (ISP). When one of the options is selected, the Wizard displays the appropriate configuration parameters. Figure 3-5 WAN Type Dynamic IP Address –... -
Page 42: Figure 3-6 Wan Type - Static Ip Address
Initial Configuration Figure 3-6 WAN Type - Static IP Address For the static IP option, you are prompted for the following information (as supplied by your ISP): IP Address – If your ISP has assigned you a fixed IP address, enter the address here. -
Page 43: Figure 3-7 Wan Type - L2Tp
Using the Setup Wizard Figure 3-7 WAN Type - L2TP For the L2TP option, you are prompted for the following information (specified by the service provider): User Name – Enter your user name for connecting to the L2TP service, as supplied by the service provider. -
Page 44: Figure 3-8 Wan Type - Pppoe
Initial Configuration Figure 3-8 WAN Type - PPPoE For the PPPoE option, you are prompted for the following information (specified by the service provider): PPPoE Network Server – The IP address of the PPPoE server, as specified by the service provider. Keep Alive –... -
Page 45: Figure 3-9 Profile Configuration
Using the Setup Wizard Profile Settings – A profile allows a user to set specific details for connecting to various WiMAX service providers. The OD200 must have at least one profile configured to be able to connect to a WiMAX service. -
Page 46: Figure 3-10 Dns Configuration
Initial Configuration DNS (Domain Name System) – A DNS server is like an index of IP addresses and Web host name addresses. When you type a Web address into your browser, such as www.awbnetworks.com, a DNS server will find that name in its index and translate it to a matching IP address, such as 211.21.189.106. -
Page 47: Figure 3-11 Wizard Setup Finished
Using the Setup Wizard Wizard Setup Finished – When the wizard set up steps are completed, click on the Home button to return to the Home page. Figure 3-11 Wizard Setup Finished 3-11... -
Page 48: The Advanced Setup Menu
Initial Configuration The Advanced Setup Menu The Advanced Setup menu provides access to all the configuration settings available for the OD200. Figure 3-12 Advanced Setup Each primary menu item is sumarized below with links to the relevant section in this guide where configuration parameters are described in detail: •... -
Page 49: Chapter 4: System Settings
Resets the device Host Name The OD200 allows you to define a name that identifies your unit and the domain name used by the local network. Setting a host name enables the web interface to be accessed using an easy-to-remember name instead of its IP address. -
Page 50: System Time
System Settings System Time The OD200 uses the Simple Network Time Protocol (SNTP) to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the device enables the system log to record meaningful dates and times for event entries. -
Page 51: Administrator Settings
Administrator Settings Administrator Settings The Administrator Settings page enables you to change the default password for management access to the OD200. Figure 4-3 Setting a Password Current Password – You need to first enter your current administrator password to be able to configure a new one. (Default: admin) Password –... -
Page 52: Configuration Tools
System Settings • Firmware Update – Downloads an operation code file from the web management station to the OD200 using HTTP. Use the Browse button to locate the code file locally on the management station and click Apply to proceed. -
Page 53: Figure 4-7 Backup/Restore Settings
Configuration Tools When you select “Backup Settings/Restore Settings” and click Apply, The following page displays. Figure 4-7 Backup/Restore Settings Backup Settings – Saves the current configuration settings to a file named “config.bin” on the web management station. Restore Settings – Restores a saved configuration file to the unit. You can use the Browse button to locate the file on the web management station. -
Page 54: System Status
System Settings System Status The system status page displays connectivity status information for the unit’s WiMAX (WAN) and LAN interfaces, firmware and hardware version numbers, and the number of clients connected to your network. Figure 4-8 System Status – Internet INTERNET –... -
Page 55: Figure 4-10 System Status - Information
System Status GATEWAY – Display system IP settings, as well as DHCP, NAT and firewall status: • IP Address – Displays the unit’s IP address. • Subnet Mask – Displays the subnet mask. • DHCP Server – Displays the DHCP server status. •... -
Page 56: System Log
System Settings System Log The System Log page allows you to display system event messages. The logged messages can serve as a valuable tool for isolating device and network problems, and also indicate if any unauthorized attempts have been made to gain access to your network. -
Page 57: Reset
Reset Reset The Reset page allows you to restart the device’s software. If the unit stops responding correctly or in some way stops functioning, performing a reset can clear the condition. Figure 4-12 Reset Unit Reset – Resets the unit. All current settings are retained. - Page 58 System Settings 4-10...
-
Page 59: Chapter 5: Gateway Configuration
Chapter 5: Gateway Configuration The information in this chapter covers the configuration options for the OD200’s Internet gateway functions. The OD200 provides comprehensive firewall features and NAT isolation for Internet traffic passing from the WiMAX service provider to the local network connected to the LAN ports. -
Page 60: Wan Settings
Gateway Configuration WAN Settings Select the WAN connection type used by your service provider and specify DNS (Domain Name System) servers. Figure 5-1 WAN Settings The unit can be connected to your ISP in one of the following ways: Dynamic IP Address – Selects configuration for an Internet connection using DHCP for IP address assignment. -
Page 61: Dynamic Ip Address
WAN Settings Dynamic IP Address For dynamic IP assignment from the service provider, the unit functions as a Dynamic Host Configuration Protocol (DHCP) client. When enabled, no other settings are required. Figure 5-2 Dynamic IP Address Static IP Settings Selecting Static IP Address for the WAN type enables you to enter static IP settings as assigned by the service provider. -
Page 62: L2Tp Settings
Gateway Configuration L2TP Settings If your service provider supports Layer 2 Tunneling Protocol (L2TP) for your Internet connection, configure the settings described below. Figure 5-4 L2TP Settings User Name – Enter your user name for connecting to the L2TP service, as supplied by the service provider. -
Page 63: Pppoe Settings
WAN Settings PPPoE Settings If your service provider supports Point-to-Point Protocol over Ethernet (PPPoE) for your Internet connection, configure the settings described below. Figure 5-5 PPPoE Settings PPPoE Network Server – The IP address of the PPPoE server, as specified by the service provider. -
Page 64: Dns
Gateway Configuration DNS (Domain Name System) server addresses are usually provided by service providers, however if you want to specify certain servers, the DNS page enables you to enter primary and secodary DNS addresses. Figure 5-6 DNS Settings Domain Name Server (DNS) Address – Address of the primary DNS server, specified in the form of 0.0.0.0 Secondary DNS Address (optional) –... -
Page 65: Lan
The OD200 must have a valid IP address for management using a web browser and to support other features. The unit has a default IP address of 192.168.1.1. You can use this IP address or assign another address that is compatible with your existing local network. -
Page 66: Dhcp Client List
"internal" IP addresses to one "external" IP address on devices at the edge of a network. For the OD200, the internal (local) IP addresses are the IP addresses assigned to local PCs by the DHCP server, and the external IP address is the IP address assigned to the WiMAX interface. -
Page 67: Figure 5-9 Virtual Server
Figure 5-9 Virtual Server Private IP – The IP address of the server on the local Ethernet network. The specified address must be in the same subnet as the OD200 and its DHCP server address pool. (Range: 192.168.1.1 to 192.168.1.254) Private Port –... -
Page 68: Port Mapping
Gateway Configuration Port Mapping Some applications, such as Internet gaming, videoconferencing, Internet telephony and others, require multiple connections. These applications cannot work with Network Address Translation (NAT) enabled. If you need to run applications that require multiple connections, use port mapping to specify the additional public ports to be opened for each application. -
Page 69: Dmz
Firewall The OD200 provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. You can also block access to the Internet from clients on the local network based on IP addresses and TCP/UDP port numbers, or specific MAC addresses. -
Page 70: Firewall Options
Gateway Configuration Firewall Options The OD200’s firewall enables access control of client PCs, blocks common hacker attacks, including IP Spoofing, Land Attack, Ping of Death, Smurf Attack, TCP null scan, ICMP defect, and TCP SYN flooding. The firewall does not significantly affect system performance and it is best to leave it enabled to protect your network. -
Page 71: Client Filtering
Firewall Client Filtering You can block access to the Internet from clients on the local network by specifying IP addresses and TCP/UDP port numbers. You can configure up to five IP filters on the unit. Figure 5-14 Client Filtering Settings Enable Client Filter –... -
Page 72: Mac Control
Gateway Configuration MAC Control You can block access to the Internet from clients on the local network by MAC addresses. You can configure up to 32 MAC address filters on the unit. Figure 5-15 MAC Control MAC Address Control – Enables the feature. (Default: Enabled) Block Connect to Internet –... -
Page 73: Route
Route Route The Routing Table displays the list of static routes on the unit. Figure 5-16 Routing Table Destination LAN IP – The IP address that identifies the IP subnet of the remote network. Subnet Mask – The mask that identifies the IP subnet of the remote network. Gateway –... -
Page 74: Upnp
Gateway Configuration UPnP UPnP (Universal Plug and Play Forum) provides inter-connectivity between devices supported by the same standard. Figure 5-17 UPnP Setting UPnP – Enables UpnP support on the unit. (Default: Enabled) 5-16... -
Page 75: Chapter 6: Wimax Settings
Profile Configuration A profile allows a user to set specific details for connecting to various WiMAX service providers. The OD200 must have at least one profile configured to be able to connect to a WiMAX service. Figure 6-1 WiMAX Profile Configuration Operator ID –... -
Page 76: Authentication
WiMAX Settings Operator Restriction – When enabled, the user can only connect to the service provider specified in the profile. The user cannot roam to other networks. When disabled, the operator specified in the profile will be used when base stations are detected, otherwise the user can roam to other networks. -
Page 77: Subscriber Station Information
Password – The user password required for EAP-TTLS authentication. (Default: hello) Subscriber Station Information The SSInfo page displays information about the software versions on the OD200 unit. Figure 6-4 Subscriber Station Information Firmware Version – The version of software code running on the unit. -
Page 78: Antenna Setting
WiMAX Settings Antenna Setting The OD200 provides the option of using an external antenna instead of the antennas integrated into the unit. If you decide to use an external antenna, set the Antenna Selection setting to “External.” Figure 6-5 WiMAX Antenna Setting Antenna Selection –... -
Page 79: Chapter 7: Voip Settings
This encoding and decoding is from a analog signal (your voice) into a digital signal (data packets) and then back into an analog signal. The OD200 uses Session Initiation Protocol (SIP) as the control mechanism that sets up, initiates, and terminates calls between a caller and a called party. The SIP messaging makes use of “Proxy,”... -
Page 80: Sip Account
Always Proxy Outbound – Forces all SIP requests to be forwarded through local proxy servers. (Default: Disabled) Expire Time – The time the OD200 waits for a response from a proxy server before a VoIP call fails. (Range: 60-4294967295 seconds; Default: 3600 seconds) User Name –... -
Page 81: Sip Setting
SIP Setting SIP Register – The IP address of the SIP registrar server. A registrar is a server that accepts SIP register requests and places the information it receives in those requests into the location service for the domain it handles. SIP Register Port Number –... -
Page 82: Dial Plan
A dial-plan string can be specified to control phone numbers dialed out through the OD200. A dial plan describes the number and pattern of digits that a user dials to reach a particular telephone number. Access codes, area codes, specialized codes, and combinations of the number of digits dialed can all be part of a dial plan. -
Page 83: Figure 7-3 Dial Plan Settings
Dial Plan Figure 7-3 Dial Plan Settings The function of elements allowed in a dial plan are described in the table below: Table 7-1. Dial Plan Elements Element Example Description xxxx Represents a digit of any value ( 0 to 9) that can be dialed on a phone. -
Page 84: Call Feature
VoIP Settings Call Feature The OD200 allows you to configure several call features, such as call waiting and call-forwarding. Other call features can be implemented by pressing specific phone buttons or entering dial patterns. The table below describes the various call features available. -
Page 85: Figure 7-4 Call Features
Call Feature Figure 7-4 Call Features Call Waiting – Enables a call waiting alert. If during a call there is another incoming call, an alert tone is heard. You can place the active call on hold (press the “Flash,” “Flash Hook,” or “Hold” button on the phone) and switch to the incoming call. (Default: Disabled) Call Waiting Timeout –... -
Page 86: Codecs
Figure 7-5 Codecs Codec – Lists the codecs supported by the OD200. You can enable specific codecs to use, or enable all. Alternatively, you may want to disable certain codecs, such as high-bandwidth codecs, to preserve network bandwidth. -
Page 87: Call Block Setting
G729ab instead of a high-bandwidth G711 codec. Select a codec in the list, then use the UP and DOWN buttons to set the priority. The OD200 attempts to use the codec highest in the list before trying the next lower one. -
Page 88: Phone Setting
For example, you can specify how long a phone will ring and how long a dial tone is heard on a phone. The OD200 also enables the line delay to be specified for each phone so that the caller’s voice echo is cancelled. -
Page 89: Chapter 8: Wi-Fi Settings
Chapter 8: Wi-Fi Settings The OD200 IDU includes an IEEE 802.11g radio interface for local Wi-Fi communications. The Wi-Fi set up pages include configuration options for the radio signal characteristics and Wi-Fi security. The Wi-Fi configuration pages include the following options. -
Page 90: Figure 8-1. Wireless Settings
Wi-Fi Settings Figure 8-1. Wireless Settings Interface Status – Enables the Wi-Fi radio. Network Name (SSID) – The Service Set ID (SSID) that identifies the Wi-Fi network. The SSID is case sensitive and can consist of up to 32 alphanumeric characters. - Page 91 Wireless Settings Working Mode – Selects the operating mode for the 802.11g radio. (Default: B/G Mixed Mode) • B/G Mixed Mode: Both 802.11b and 802.11g clients can communicate with the unit (up to 54 Mbps). • G Only Mode: Only 802.11g clients can communicate with the unit (up to 54 Mbps).
- Page 92 SSID of “ANY” can read the SSID from the beacon, and automatically set their SSID for immediate connection to the OD200. When enabled, the unit does not include its SSID in beacon messages. This provides a basic level of security, since wireless clients must be configured with the SSID to connect to the OD200.
-
Page 93: Wireless Security
Wireless Security The OD200’s Wi-Fi interface is configured by default as an “open system,” which broadcasts a beacon signal including the configured SSID. Wireless clients with a configured SSID of “ANY” can read the SSID from the beacon, and automatically set their SSID to allow immediate connection to the wireless network. -
Page 94: Wep Shared Key Security
The option “Open System” together with encryption disabled is equivalent to no security, all clients will be able to immediately connect to the Wi-Fi network. The following sections describe the security options available for the OD200 Wi-Fi network. WEP Shared Key Security... -
Page 95: Wpa/Wpa2 Security
Wireless Security WPA/WPA2 Security The WPA and WPA2 modes use IEEE 802.1X as their basic framework for user authentication and dynamic key management. IEEE 802.1X access security uses Extensible Authentication Protocol (EAP) and requires a configured Remote Authentication Dial-in User Service (RADIUS) authentication server to be accessible in the enterprise network. -
Page 96: Wpa/Wpa2 Psk Security
Wi-Fi Settings Note: This guide assumes that you have already configured a RADIUS server in the attached wired network to support the unit. Configuration of RADIUS server software is beyond the scope of this guide, refer to documentation provided with the RADIUS server software. -
Page 97: Mac Authentication
Wireless clients can be authenticated for network access by checking their MAC address against a local database configured on the OD200. You can configure a list of up to 32 wireless client MAC addresses in the filter list to either allow or deny network access. - Page 98 Wi-Fi Settings 8-10...
-
Page 99: Appendix A: Troubleshooting
Appendix A: Troubleshooting Diagnosing LED Indicators Table A-1 Troubleshooting Chart Symptom Action Power LED is Off • AC power adapter may be disconnected. Check connections between the unit, the AC power adapter, and the wall outlet. Power LED is Red •... -
Page 100: Cannot Access Web Management
Troubleshooting Cannot Access Web Management If the management interface cannot be accessed using a web browser: • Be sure the management station is correctly configured for TCP/IP. The IP settings should be set to “obtain an IP address automatically.” • Try a Ping command from the management station to the unit’s IP address to verify that the entire network path between the two devices is functioning correctly. -
Page 101: Appendix B: Specifications
Appendix B: Specifications Physical Specifications IDU Ports 4 LAN ports, 10/100BASE-TX with auto-negotiation, RJ-45 connector 2 FXS ports (PHONE1, PHONE2), RJ-11 connector Network Interface RJ-45 connector, auto MDI/X: 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) LED Indicators System: Power, WiMAX signal strength, WiFi Ports: Link/Activity... -
Page 102: Wimax Specifications
Specifications WiMAX Specifications Antennas Omnidirectional: Built-in dual dipole antennas Transmit: Single antenna Receive: Two antennas using Maximal-Ratio Combining (MRC) Gain: 3 dBi at 2.5 GHz, 4 dBi at 3.5 GHz Impedance: 50 Ohm Switched-Beam: Built-in dual switched-beam antennas (each antenna is a 5-way pentagon structure with 4 flat-patch elements in each segment) Transmit: Single antenna Receive: Two antennas using Maximal-Ratio Combining (MRC) -
Page 103: Wi-Fi Specifications
Wi-Fi Specifications G.726 G.729ab G.723 Voice Quality VAD (Voice Activity Detection) CNG (Comfortable Noise Generation) Echo cancellation (G.165/G.168) Adaptive jitter buffer, up to 200 milliseconds DTMF tone detection and generation Call Features Call transfer Call waiting/hold/retrieve 3-way conference call Call blocking T.38 fax relay Dial plan (E.164 dialing plan) Call forwarding: No Answer/Busy/All... -
Page 104: Compliances
Specifications RF Receive Sensitivity 802.11b: -88 dBm @ 11 Mbps 802.11g: -74 dBm @ 54 Mbps Compliances Emissions FCC Part 15B Class B VCCI Class B EN 55022 Class B EN 55024 EN 61000-3-2 EN 61000-3-3 Emmunity EN 61000-4-2/3/4/5/6/11 WiMAX Radio Signal Certification FCC Part 27 EN 300 326, EN 300 326-1, EN 300 326-3 Wi-Fi Radio Signal Certification... -
Page 105: Appendix C: Cables And Pinouts
Appendix C: Cables and Pinouts Twisted-Pair Cable Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. -
Page 106: Straight-Through Wiring
Cables and Pinouts Table C-1. 10/100BASE-TX MDI and MDI-X Port Pinouts MDI-X Signal Name MDI Signal Name Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) Not used... -
Page 107: Rj-11 Ports
RJ-11 Ports RJ-11 Ports Standard telephone RJ-11 connectors and cabling can be found in several common wiring patterns. These six-pin connectors can accommodate up to three wire pairs (three telephone lines), but usually only one or two pairs of conductor pins and wires are implemented. - Page 108 Cables and Pinouts...
-
Page 109: Appendix D: License Information
Appendix D: License Information This product includes copyrighted third-party software subject to the terms of the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other related free software licences. The GPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. - Page 110 License Information We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.
- Page 111 The GNU General Public License a). You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b). You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
- Page 112 License Information c). Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
- Page 113 The GNU General Public License consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
- Page 114 License Information NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS"...
- Page 115 Glossary 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. Advanced Encryption Standard (AES) An strong encryption algorithm that implements symmetric key cryptography.
- Page 116 Glossary Encryption Data passing between the access point and clients can use encryption to protect from interception and evesdropping. Extensible Authentication Protocol (EAP) An authentication protocol used to authenticate network clients. EAP is combined with IEEE 802.1X port authentication and a RADIUS authentication server to provide “mutual authentication”...
- Page 117 Glossary Simple Network Management Protocol (SNMP) The application protocol in the Internet suite of protocols which offers network management services. Simple Network Time Protocol (SNTP) SNTP allows a device to set its internal clock based on periodic updates from a Network Time Protocol (NTP) server.
- Page 118 Glossary Glossary-4...
- Page 119 Index AC power adapter encryption administrator password, setting ESSID administrator settings Ethernet ports Advanced Setup menu 3-12 antennas authentication factory defaults, restoring type 8-4, 8-5 firewall protection 5-11 auto-logout time firmware update 4-3, 4-4 fixed-IP xDSL 3-5, 5-2 backup settings button, Reset Gateway address 5-3, 5-15...
- Page 120 Index logging, system messages restore settings login, web RJ-45 ports lost password, recovery runtime code version MAC address filters security, options 5-14 mapping ports, NAT service provider connection 5-10 MDI/MDI-X, automatic Setup Wizard 3-10 host settings launching open system 8-4, 8-5 time zone operating frequency B-2, B-3...
- Page 121 Index web management interface WiMAX connection status access Wizard, setup login troubleshooting Index-3...
- Page 122 Index Index-4...
- Page 124 OD200 E032008-CS-R01 1************...