Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MK Diamond Products SDG-11
Summary of Contents for MK Diamond Products SDG-11
-
Page 1: Parts List
MK-SINGLE DISC GRINDER www.mkdiamond.com OWNERS MANUAL PARTS LIST & OPERATING INSTRUCTIONS SDG-3 SDG-11 Revision 202 11.2011 Manual 158273 Caution: Read all safety and operating instructions before using this equipment. This parts list MUST accompany the equipment at all times. - Page 2 INTRODUCTION Congratulations on your purchase of a MK-SDG Grinder. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-SDG Grinder should provide you with years of service. In order to help you, we have included this manual.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY Safety Messages Damage Prevention Message General Safety Precautions and Hazard Symbols Rules for Safe Operation California Proposition 65 Message Electrical Requirements 8-10 Safety Label Locations Product Specifications UNPACKING and TRANSPORT Unpacking Contents Transport ASSEMBLY and OPERATION Handlebar Adjustment Grinding Discs Installation Gasoline Engine Unit... -
Page 4: Safety Messages
MK-SDG SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. SAFETY MESSAGES A safety message alerts you to potential hazards that could hurt you or others. - Page 5 MK-SDG SAFETY MAKE THE WORKSHOP KID PROOF Make the workshops kid proof by using padlocks, master switches or by removing starter keys. DO NOT FORCE THE TOOL A power tool will do a job better and safer operating at the rate for which it was designed. USE THE RIGHT TOOL DO NOT force a tool or an attachment, to do a job that it was not designed to do.
-
Page 6: California Proposition 65 Message
MK-SDG SAFETY USE RECOMMENDED ACCESSORIES Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. NEVER STAND ON THE TOOL Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally contacted. - Page 7 MK-SDG SAFETY HAZARD SYMBOLS ELECTRICAL SHOCK NEVER touch electrical wires or components while the engine is running. They can be sources of electrical shock which could cause severe injury or burns. ROTATING PARTS Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the motor with covers, shrouds, or guards removed.
-
Page 8: Electrical Requirements
MK-SDG SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electric cur- rent to reduce the risk of electric shock. - Page 9 MK-SDG SAFETY WARNING To avoid the possibility of the appliance plug or receptacle getting wet, position the machine to one side of a wall mounted receptacle. This will prevent water from dripping onto the receptacle or plug. A “drip loop,” shown in the picture below, should be arranged by the user to properly position the power cord relative to the power source.
- Page 10 MK-SDG SAFETY WARNING To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands. WARNING Use of under sized extension cords result in low voltage to the motor that can result in motor burnout and premature failure.
- Page 11 MK-SDG SAFETY OPERATION & SAFETY DECALS The MK-SDG is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. Should any of these operation or safety decals become unread- able, replacements can be obtained by calling (800) 262-1575. CAUTION WARNING DO NOT...
-
Page 12: Product Specifications
Dust shroud helps contain grinding debris. • Works on concrete slabs, terrazzo, brick, stone and ceramic tile floors. SPECIFICATIONS Specifications for the MK-SDG are listed in the table below. Model MK-SDG-11 MK-SDG 3 Engine Honda Baldor / Leeson Power GX340... -
Page 13: Unpacking
If within one (1) Year from the date of purchase, this MK Diamond saw fails due to defect in material or workmanship, MK will repair it, free of charge when the unit is re- turned to the dealer where it was purchased. This warranty DOES NOT cover normal wear or damage resulting from operator abuse. In no event shall MK Diamond Products, Inc. -
Page 14: Handlebar Adjustment
MK-SDG ASSEMBLY ASSEMBLY Follow the diagram below to prepare your MK-SDG for operation. HANDLEBAR ADJUSTMENT Adjust the Handlebar, as shown in the figure to the right, for ease of operation and comfort of the user. GRINDING DISCS INSTALLATION You need to install the grinding discs before operation of the MK-SDG The figure to the left shows the components needed to install the discs. - Page 15 MK-SDG OPERATION FOR GASOLINE ENGINE BEFORE STARTING 1. Use correct diamond wheel for grinding conditions. 2. Ensure wheel mountings are clean and bolts are tightened securely. 3. Check water jet for adequate flow. 4. Place grinding wheels on surface. 5. Start and warm up engine. Refer to engine owners manual for details. 6.
-
Page 16: Cleanup
MK-SDG CLEANUP CLEAN UP CAUTION Engine parts are extremely hot following use. Allow engine to cool 1/2 hour before cleaning. Use care during cleanup to avoid injury. 1. To extend operating life, the MK-SDG should be cleaned following every use. NOTE: 2. - Page 17 NOTES...
-
Page 18: Exploded View
MK-SDG EXPLODED VIEW Gas Engine... - Page 19 MK-SDG EXPLODED VIEW Gas Engine...
-
Page 20: Exploded View
MK-SDG EXPLODED VIEW Electric Engine GD13 GD15 GD16 GD14 GD17 GD18 GD19 GD20 GD21 GD22 GD23 GD24 GD23 GD25 GD27 GD28 GD26 GD32 GD33 GD20 GD32 GD33 GD29 GD33 GD34 GD35 GD10 GD12... -
Page 21: Parts List
Part No. Assembly, Accessory Pack Grinding Wheels 10” (Reference only) Reference Pallet (not shown) 158259 Carton, SDG-11 Grinder (not shown) 158272 Tube, Owner’s Manual (not shown) 155419 Manual, Owner’s (not shown) 158273 Bolt, Hex HD, 3/8-24 x 1 Grinding Disk, Mounting... -
Page 22: Parts List
MK-SDG PARTS LIST Washer, Lock, Split 1/2 153524 Washer, Flat SAE 1/2 150924 Shaft, 1” Dia Large Gear 157302 Flexible Mount, Morflex (Morse 402 Insert) 157411 Mount, Grinding Wheel 157407 Screw, Hex HD Cap 3/8-16 x 2 1/2 156030 Screw, Flt. HD. Sc. 3/8-16 x 2 1/2 157562 Nut, 3/8-16, Hex Nylock 152505... - Page 23 MK-SDG PARTS LIST GD17 Gasket, 30A Switch Box 159491 GD18 Seal, Level, 30A Switch Box 159492 GD19 Lever, On/Off, 30A Switch Box 159490 GD20 Washer, #10 SAE Flat 154369 GD21 Washer, Lock, IT, #10 158336 GD22 Screw, Pan Head #10-24 x 5/16 159494 GD23 Screw, Flat Head 6-32 X 5/16...
- Page 24 NOTES...
-
Page 25: Accessories
MK-SDG ACCESSORIES MK-1010/MK-1020 SERIES of grinding heads are designed to give rough concrete surfac- es the smoothest finish in the quickest time. Available in either 10 or 20 segment configura- tions. Hard bond is for grinding green concrete and asphalt. Soft bond is for grinding cured concrete. -
Page 26: Ordering Information
MK-SDG ORDERING & RETURN ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: •... - Page 27 © COPYRIGHT 2011, MK DIAMOND PRODUCTS, INC. ALL RIGHTS RESERVED. The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their re- spective owners and used with permission.
- Page 28 MK- SINGLE DISC GRINDER OWNERS MANUAL, PARTS LIST & OPERATING INSTRUCTIONS MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 421-5830 Phone: (310) 539-5221 Fax: (310) 539-5158 www.mkdiamond.com...