Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MK Diamond Products MK-SDG-7
Summary of Contents for MK Diamond Products MK-SDG-7
- Page 1 MK-SDG-7 www.mkdiamond.com OWNER'S MANUAL,OPERATING INSTRUCTIONS & PARTS LIST Revision 111 08.2018 Manual Part# 168146 Caution: Read all safety and operating instructions before using this equipment. This manual MUST accompany the equipment at all times.
- Page 2 INTRODUCTION Congratulations on your purchase of a MK-SDG-7. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-SDG-7 should provide you with years of service. In order to help you, we have included this manual.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY Safety Messages Safety Precaution California Proposition 65 Message General Safety Electrical Requirements and Grounding Requirements 9-11 Safety Label Locations Product Specifications and Features ASSEMBLY Assembly Replace Cup Wheel Operation EXPLODED VIEW and PART LISTS Exploded View & Parts List 16-19 ACCESSORIES ORDERING and RETURN INSTRUCTIONS Accessories... -
Page 4: Safety Messages
MK-SDG-7 SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. Safety warnings and guidelines do not by themselves eliminate danger. - Page 5 MK-SDG-7 SAFETY PERSONAL PROTECTIVE EQUIPMENT ALWAYS wear approved respiratory, head, ear and eye protection when operating this machine. ACCIDENTAL STARTS! Before starting the engine/motor, be sure the ON/OFF switch is in the OFF position to pre- vent accidental starting. Place the ON/OFF switch in the OFF position before performing any service operation.
- Page 6 MK-SDG-7 SAFETY USE PROPER APPAREL DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may be caught in moving parts. Non-slip footwear is recommended. Wear protective hair cover- ing to contain long hair. SECURE WORK Clamps or a vise should be used to hold work whenever practical. Keeping your hands free to operate a power tool is safer.
- Page 7 MK-SDG-7 SAFETY CHECK FOR DAMAGED PARTS Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Always check moving parts for proper alignment or binding.
-
Page 8: California Proposition 65 Message
MK-SDG-7 SAFETY SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. -
Page 9: General Safety
MK-SDG-7 SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. - Page 10 MK-SDG-7 SAFETY ELECTRIC MOTOR SAFETY For maintenance care and operation of the electric motor, refer to your electric motor instruction book- let furnished with the electric motor. Protect the electric motor from dust as much as possible and keep ventilating openings clean. Before plugging in the machine, make sure that the outlet voltage is within the voltage marked on the machines's data plate.
- Page 11 MK-SDG-7 SAFETY WARNING To reduce the risk of electrocution, keep all connections dry and off the ground. A Ground Fault Cir- cuit Interrupter (GFCI) should be provided on the circuit(s) or outlet(s) to be used for this machine. Receptacles are available having built-in GFCI protections and may be used for this measure of safety.
-
Page 12: Safety Label Locations
MK-SDG-7 SAFETY OPERATION & SAFETY DECALS The MK-SDG-7 is equipped with a number of safety decals provided for operator safety and mainte- nance information. Should any of these decals become unreadable, replacements can be obtained by calling (800) 421-5830. NOTICE... -
Page 13: Product Specifications And Features
MK-SDG-7 FEATURES & PRODUCT SPECIFICATIONS FEATURES • 120V/15 Amp motor, disc RPM of 3,500 • Constructed with sturdy heavy gauge steel • MK-IXL vacuum shroud for dust control • Shroud accommodates diamond cup wheels up to 7" in diameter • Attaches to a vacuum/dust collection system, reducing risk respirable dust •... -
Page 14: Assembly
MK-SDG-7 ASSEMBLY ASSEMBLY Place shroud on flange. Place the handle bar assembly Tighten clamp with wing nut so it into the base and screw the tri- is firmly attached. knob in to hold it in place. Attach the vacuum hose to the shroud and vacuum outlet port. -
Page 15: Operation
MK-SDG-7 OPERATION OPERATION BEFORE STARTING 1. Inspect area before grinding. Remove all debris that could damage diamond cup wheel or cause a hazardous situation. 2. Choose correct diamond wheel for the job condition. 3. Ensure grinding wheel mounting is clean and the retaining bolt is securely tightened. - Page 16 MK-SDG-7 EXPLODED VIEW FIGURE 1 SDG-7 PART # 166859...
- Page 17 MK-SDG-7 PARTS LIST FIGURE 1 SDG-7 PART # 166859 ITEM DESCRIPTION PART # WHEEL, FRONT 5" X 2" W 138537 NUT, HEX,1/4 - 20 151893 WASHER, FLAT, SAE, 1/4 151915 CLAMP, 3/4 CUSHION LOOP 152594 SCREW, 1/4 -20 X 1/2 HEX HEAD 152608 COLLAR, SET, 3/4"...
- Page 18 MK-SDG-7 EXPLODED VIEW FIGURE 2 SWITCH BOX PART # 166858 ITEM DESCRIPTION PART # SCREW, #6 - 32 X 1/2 PAN HEAD SELF TAPPING 153459 COVER, SWITCH 154301 SWITCH, TOGGLE 125V 20A 154310 PLATE, TOGGLE SWITCH LOCKOUT 156211 SCREW, HEX HD FL, 10-24X 5/16...
- Page 19 NOTES...
-
Page 20: Accessories
MK-SDG-7 ACCESSORIES ACCESSORIES Recommended 7" Cup Wheels For A Variety Of Applications Single Row Grinding Cup Wheels Double Row Grinding Cup Wheels MK-304CG-1 MK-304SG-2 • 12 segment cup wheel • 24 segment cup wheel • 6mm diamond depth height • 6mm diamond depth height •... - Page 21 NOTES...
-
Page 22: Ordering Information
ORDERING, RETURN, PACKING, & AUTHORIZED SERVICE ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: •... -
Page 23: Contact
© COPYRIGHT 2017, MK DIAMOND PRODUCTS, INC. ALL RIGHTS RESERVED. The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their re- spective owners and used with permission. - Page 24 MK-SDG-7 OWNERS MANUAL, PARTS LIST, EXPLODED & OPERATING INSTRUCTIONS MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 845-3729 Phone: (310) 539-2221 Fax: (310) 539-5158 www.mkdiamond.com...