65" Wiring Diagram - Back - Zenith R50V26 Service Manual

to CONTROL
to Speaker(PR)
P.W.B.
PFT PFS,
LX-ZCAT3035-1330
E007
VM P.W.B.
PZV
PVS1
PFT
SRS P.W.B.
TUNER 1
PV154 - 923-03506

65" Wiring Diagram - Back

PR make
LEAD CLAMPER
double loop N008
PAQ1,PQD2
PQS1
PR PQS1,PDC1
PQS2 PQS2,PQD1
PQS1 PR
PQD1
PQS2
PL
PCR,MR
PCB,MB,PL
ANODE(B)
ANODE(G)
PCG
make a loop
MG
PFT
MB
MB MG
PCB
WIRE
CLAMP VO
PCG
N003
PFS
ANODE(B)
FOCUS
(G) (B)
SCREEN (G) (B)
FOCUS (G)
PFS
SCREEN (G)
FOCUS(B)
PVMS
SCREEN
SCREEN(B) (B)
SCREEN(G)
PZC FOCUS
PVC2 (B)
FOCUS
(G)
to
PCV
VM
CPT P.W.B.(B)
CPT P.W.B.(G)
P.W.B.
PZC PZC
E003 MGZ-E1630MRF-CLAMP MGZ-E1630MRF-CLAMP PZV PZV
MGZ-E1630MRF-CLAMP
E004
PSD1
PFS
PZV
PZV PZC
PZC
PL
PSD2
PR
PSD3
PAQ1
PQS2
PQS1
SIGNAL P.W.B.
TUNER 2
PFT
TERMINAL P.W.B.
ANTENNA TERMINAL BOARD.
BACK SIDE
from SENSOR P.W.B.
LEAD CLAMPER MAG-FERRITE CORE 133
N008
E001 PDS1
PCB,PCG
PL
make a loop
PDC1
PCR,PCG,PCB
MR,MG,MB,PL
SK
PL
ANODE(R)
PDF2
MB,MR
PCR,MR PAQ1
PCR
FOCUS PACK
MR
MR
FOCUS(R)
MG
SCREEN(R)
to
N007 VM
PCR
PURSE LOCK
P.W.B.
016
SCREEN(R)
MGZ-E1630MRF
E005
PDC1
FOCUS
PCV
(R) PCB,MB
PCG,MG
PCR,MR make a loop
PDF2
N003
Hold Anode(B)
make double
loops
DIGITAL
CONVERGENCE
UNIT
MB
PDS1
PDK1
MR
MG
PQD2
PDF1
PDK3
PDC1 PCR
DEFLECTION
P.W.B.
B
PDK4
FOCUS PCG
ANODE(R)
PSF
R G
ANODE(G)
LX-ZCAT2032-0930 ANODE(B)
E002
FBT
PCB
PDF1
PDKP
PQD1 PDF2
CONVERGENCE
PS
P.W.B.
NOTE: Refer to the figure (04/page) when the HV
connector (anode lead) is removed or inserted.
NOTE: Anode lead should be separated from others
wires. (min. 10mm)
Anode lead must not be twisted during the
operation of wiring dress.
5-7
Refer to the figure below
about the assembly if
FOCUS PACK leads.
SCREEN
(B) (G) (R)
PDF2
(B) (R)
(G)
FOCUS
PSF
FOCUS PACK
PDF2,PSF
FOCUS(R,G,B)
UFPK
SCREEN(R,G,B)
MAG-FERRITE CORE 133
N001
E001
BINDER
PQD1 make a loop
PQD2 make double loop
N001
SK BINDER
to Speaker(PL) P#:3763752
make a loop
PL
CATCH HOLDER
PAQ1 (BACK VIEW)
PQD2
PQS1
PQD1
Note: for J#02~, for J#01 ferrite
position is on the upper clamp
PQS2
MARK SHOULD BE APPLY A LEAD CLAMP(N008)
(LEAD CLAMP PARTS No. IS 3813121.)
POWER SUPPLY
P.W.B.
MARK SHOULD BE APPLY A LEAD CLAMP(N011)
(LEAD CLAMP PARTS No. IS 3875441.)
PA
POWER CORD
THIS DRAWING APPLIES
TO R65W28
(ZP14C CHASS.).
ZP26/28 - EXPLODED VIEWS