Replacing The Light Bulb; Cleaning The Oven Door - Hotpoint OS 897D P/HP S Operating Instructions Manual

affect the rust protection.
• The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse and dry thoroughly. Do not
use abrasive powders or corrosive substances.
• The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
• All accessories can be washed like everyday crockery,
and are even dishwasher safe.
! Never use steam cleaners or pressure cleaners on the
appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and
a non-abrasive cleaning product, then dry thoroughly with a
soft cloth. Do not use rough abrasive material or sharp metal
scrapers as these could scratch the surface and cause the
glass to crack. For more thorough cleaning purposes, the
oven door may be removed:
1. Open the oven door fully (see diagram).
2. Use a screwdriver to lift up and turn the small levers F
located on the two hinges (see diagram).
Inspecting the seals
Check the door seals around the oven regularly. If the seals
are damaged, please contact your nearest Service Centre
(see Assistance). We recommend that the oven is not used
until the seals have been replaced.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
F
3. Grip the door on the two outer
sides and close it approximately
half way. Pull the door towards you,
lifting it out of its slot (see diagram).
To replace the door, reverse this
sequence.

Replacing the light bulb

Lamp
Holder
compartment
Lamp
Glass cover
! Do not touch the light bulb directly with your hands.
! Do not use the oven lamp as/for ambient lighting.
Automatic cleaning using the FAST
CLEAN function
During the FAST CLEAN cycle, the internal temperature of the
oven reaches 500°C. The pyrolytic cycle is activated, burning
away food and grime residues. Dirt is literally incinerated.
Keep children well away from the appliance during the
automatic cleaning cycle, as the surfaces may become
extremely hot. Particles may ignite inside the oven due to
the combustion process. Particles may ignite inside the oven
as a result of the combustion process. This is not a cause
for concern; it is a normal process and is completely safe.
Before initiating the FAST CLEAN mode:
! We recommend the duration of the first automatic cleaning
cycle is set to 120 minutes.
! The oven should be cold. If the oven is too hot, the pyrolytic
cycle may not start. Wait for the oven to cool down.
• Remove larger food residues from inside the oven using
a damp sponge. Do not use detergent.
• Remove all accessories.
• Remove the DIVIDER.
• Do not leave tea towels or pot holders on the oven handle.
! The cycle will only begin once the oven door has been closed.
To start the FAST CLEAN cycle, turn the EXTRALARGE
SPACE FUNCTION knob to
The SET TIME button may be used to select the desired
cleaning level. There are three default time settings, which
cannot be modified:
1. Economy (ECO): turn the knob towards " ". Duration: 1 hour.
2. Normal (NOR): initial level. Duration: 1 hour and 30 minutes.
3. Intensive (INT): turn the knob towards " ". Duration: 2 hours.
4. Press the button to confirm.
To replace the oven light
bulb:
1. Remove the glass cover
of the lamp-holder.
2. Remove the light bulb and
replace it with a similar one:
halogen lamp voltage 230 V,
wattage 25 W, cap G 9.
3. Replace the glass cover
(see diagram).
.
15
GB