Related Manuals for Williams Sound DWD 102
Summary of Contents for Williams Sound DWD 102
- Page 1 DWD 102 Digi-Wave™ Dual-Bay Docking Station User manual Compatible with Digi-Wave™ Models: DLT 100 2.0, DLR 60 2.0 and DLR 60 MAN 180C...
-
Page 2: System Overview
(4) RBP 005 Support Pads 1/8” (thick) (4) RBP 006 Support Pads 1/16” (thin) Recycling Instructions Help Williams Sound protect the environment! Please take the time to dispose of your equipment properly. Product Recycling for Customers in the European Union: Please do NOT dispose of your Williams Sound equipment in the household trash. -
Page 3: Connectors And Controls
Connectors and Controls Figure 1: Rear View Bay 2 Bay 1 Auto/ Auto/ Line Line Line Line Manual Manual Line Line Line Line Input Inputs Output Outputs Switch Switch Input Inputs Output Outputs Bay 2 Bay 2 Bay 2 Bay 2 Bay 2 Bay 1 Bay 1... -
Page 4: Setup Instructions
4. Using the appropriate line cord (US, EURO, UK or AUS) into the TFP 048, plug the TFP 048 power supply into the AC wall outlet. Plug the power connector into the rear of the DWD 102 unit (figure 1). The green LED power indicator should light up (Figure 2). - Page 5 Figure 3: Digi-Wave™ Dock Functions DLT 100 2.0 DLR 60 2.0 / DLR 60 Yes - with NiMH AAA batter- Charges Unit ies in DLR only; if no batteries with Dock Power Yes (internal battery) present dock will power DLR (if battery switch is in NiMH position).
- Page 6 DLT microphone mixing with dock sources The dock’s inputs - two mono RCA jacks (-10dBV) and one XLR jack (+4dBu) - are mixed together in the dock, then sent to the DLT 100 2.0. The DLT 100 2.0 then mixes the dock audio with it’s microphone before transmitting. Depending upon what sources are being mixed, there may be a level mismatch between the dock and the DLT’s microphone level.
- Page 7 Installing the Support Pads Two sets of supporting pads have been supplied with the dock to support the back of the unit(s) when sitting in the dock; thick (1/8”) and thin (1/16”). Use the table below to choose which pad thickness to use (Figure 5). See the diagram below showing where to affix the pads (Figure 6).
- Page 8 Output: 24VDC, 750mA. Charging Time DLT 100 2.0: 5 hours nominal (internal LiPo Battery) DLR 60 2.0: 15 hours nominal, based on Williams Sound NiMH battery BAT 022-2. Unit Capacity 2 Units: DLT 100 2.0, DLR 60 2.0, or DLR 60. DLT 100 units will charge only (no audio).
-
Page 9: Troubleshooting
Troubleshooting No audio transmitted from docked DLT 100 2.0: 1. Make sure the DLT is seated firmly on the dock’s 30-pin connector. 2. Make sure the dock and DLT are powered ON. 3. Check the source input into the dock - make sure it is connected, powered on and playing/producing audio. - Page 10 One or more source audio levels too quiet or too loud (not mixing evenly): 1. If the RCA inputs are being used with an XLR source, both RCA inputs must be used to mix evenly with the XLR source. If using a mono RCA source, it must be wyed-out (using a Y-cable or adapter) and sent into both RCA inputs.
-
Page 11: Year Warranty
Williams Sound warrants the DWD 102 Digi-Wave™ Dual-Bay Docking Station against defects in materials and workmanship for TWO (2) years. During the first 2 years from the purchase date, we will promptly repair or replace the DWD 102. Microphones, earphones, headphones, rechargeable batteries, cables, carry cases, and most other accessory products carry a 90-day warranty. - Page 12 10300 Valley View Rd • Eden Prairie, MN 55344 800-328-6190 / 952-943-2252 • FAX: 952-943-2174 www.williamssound.com ©2014 Williams Sound • All Rights Reserved MAN 180C...
Need help?
Do you have a question about the DWD 102 and is the answer not in the manual?
Questions and answers