Husqvarna TS 250 XS Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Saw
  5. TS 250 XS
  6. Operator's manual
Husqvarna TS 250 XS Operator's Manual

Husqvarna TS 250 XS Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's manual
Read these instructions carefully and make sure
you understand them before using the TS 250 XS.
TS 250 XS


Advertisement

Table of Contents
loading

Related Manuals for Husqvarna TS 250 XS

Summary of Contents for Husqvarna TS 250 XS

  • Page 1 Operator’s manual Read these instructions carefully and make sure you understand them before using the TS 250 XS. TS 250 XS...

  • Page 2: Dust Warning

    Corporate Office 17400 West 119th Street Olathe, Kansas 66061 U.S.A. Customer Service: 800-288-5040 Customer Serv. Fax: 800-825-0028 Corporate Office: 913-928-1000 Corp. Office Fax: 913-438-7951 South Carolina Customer Service: 800-845-1312 Customer Serv. Fax: 800-257-9284 Canada Customer Service: 800-461-9589 Customer Serv. Fax: 800-728-1907 International Customer Service: 913-928-1300 Customer Serv.

  • Page 3: Table Of Contents

    WARNING! Before starting up machine make sure you completely read these instructions. Be familiar with operation of the machine before operation! EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS.

  • Page 4: Symbol Definitions

    Symbol Definitions Definición De Los Simbolos • Please read the instructions for use prior to operating the machine for the first time. • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina. • Mandatory •...
  • Page 5 • Motor Off • Parar El Motor • Use In Well Ventilated Area • Usar En Una Área Bien Ventilada • Do Not Use In Flammable Areas • No Usar In Áreas Inflamables • Machinery Hazard, Keep Hands And Feet Clear. •...
  • Page 6 • Repairs Are To Be Done By An Authorized Dealer Only • Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • Diamond Blade • Sierra Diamantada • Blade Diameter • Diámetro De La Hoja • Pulley Diameter • Diámetro De La Correa •...

  • Page 7: Decal Descriptions And Locations

    Location: Motor Assembly P/N 542 19 37-94 P/N 046327 Location: Water Pan Location: Motor Assy HUSQVARNA-TARGET STONEMATIC TS 250 XS LOGO SIDES OF WATER PAN (X2) P/N 542 19 07-30 HUSQVARNA LOGO, 250mm Long REAR OF COWL HUSQVARNA LOGO, 35mm...

  • Page 8: Saw Dimensions

    Saw Dimensions ITEM DESCRIPTION inch Saw Length 67-3/4 1721 Saw Width 33-5/8 Saw Height 22-3/4 Stand Height 30-1/4 Total Height 1346 Arbor to Top of Cart 6-9/16 Cart Length Cart Width Cart Travel 45-3/8 1153 Tray Length 67-3/4 1721 Tray Width 26-1/8 Extension Length Extension Width...

  • Page 9: Specifications

    Specifications MODEL NO. TS 250 XS TYPE 1-1/2 HP, 115/208-230/ 2 HP, 115/230V-60Hz Blade Guard 10" Capacity (250 mm) Blade Shaft RPM: 3880 3880 3-3/4” (95 mm) Max. Depth of Cut: Maximum Material Up to 24” wide x 36” long (610 x 914 mm) Size: 5/8”...

  • Page 10: Safety Warnings - Dos & Do Nots

    SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition.
  • Page 11 If you have any questions relative to its application, DO NOT use the saw until you have written Diamant Boart, Inc. and we have advised you. Husqvarna Construction Products, North America 17400 West 119th Street...
  • Page 12 What-Is-What (Parts Identification) S. Water Pan Assembly J. Blade Guard A. Set Collar T. Rolling Stand K. Electrical Receptacle B. Bearing Caps U.Conveyor Cart Assembly L. Blade Shaft Nut C. Locking Knob V. Frame Assembly M. Outer Blade Flange D. Lockbar W.

  • Page 13: Preoperation Checklist / Scheduled Maintenance

    PRE OPERATION CHECKLIST Before leaving our factory, every machine is thoroughly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions. Before starting up the machine, make sure you read this entire Operation’s Manual and are familiar with the operation of the machine.

  • Page 14: Instructions

    ASSEMBLY INDICATION MANDATORY I N F O R M AT I O N • Remove all items from the shipping carton and iden- INSTRUCTION tify: 1. Cutting Head Assembly (R) {includes Water Tube Assembly} PROHIBITION WARNING 2. Rolling Stand Assembly 3.

  • Page 15: Operating Procedures

    WARNING! materials. For the best results, always use Check that the ON/OFF switch is in the “OFF” posi- genuine Husqvarna diamond blades. Contact ® tion. your nearest dealer to select the correct blade for your specific cutting needs.

  • Page 16: Manual Thermal Overload

    ALIGNMENT PROCEDURES WARNING! Wet cutting blades can be damaged or destroyed Your saw is factory assembled and aligned pri- without sufficient water. Only blades specifically o r t o s h i p m e n t t o e n s u r e a c c u r a t e c u t s w h e n designed for dry cutting can be used without cool- your saw is delivered.

  • Page 17: Maintenance

    REPAIRS MAINTENANCE PROCEDURES We carry out all repairs in the shortest possible time and at the most economical prices. (See front page for WARNING! address and phone numbers) Contact your authorized Before performing any maintenance, ALWAYS dealer concerning maintenance and repairs. place the machine on a level surface with the motor “OFF”...
  • Page 18 WIRING DIAGRAM: 1-1/2 HP MOTOR...
  • Page 19 WIRING DIAGRAM: 2 HP MOTOR with AMMETER...
  • Page 20 542 20 11-03 2006-28...

Table of Contents