Hitachi 57UWX20B Operating Manual page 8

To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust the sound using the remote control of
the TV set. 2. See page 41 for AUDIO Advanced Settings. CONNECTING EXTERNAL VIDEO SOURCES The exact arrangement you use to connect the VCR,
camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner's
The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of
components and features. For best performance, video and audio cables should be made from coaxial shielded wire. Before Operating External Video Source
The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the
(See page 22) INPUT MODE SELECTION ORDER (ANTENNA) Ant A (INPUT) YPBPR:1 VID1 VID1 ANT NOTE: When the TV is set to VIDEO and a video
signal is not received from the VIDEO INPUT JACK on the back panel of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF),
the set will appear to be OFF. 14 CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A MONAURAL AUDIO SOURCE TO INPUT2~INPUT5 1.
Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. Connect the cable
from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack. Press the VID2~VID5 button to view the program from the
VCR or the laserdisc player. The VIDEO label disappears automatically after approximately four seconds. Press the ANT button to return to the previous
channel. 2. 3. 4. ANT A ANT A DVI-HDTV PR INPUT 1 PB Y INPUT 1 PR PB Y TO CONVERTER R (MONO)/L AUDIO TO CONVERTER R (MONO)/L
AUDIO PR ANT B INPUT 2 PB Y/VIDEO ANT B AUDIO INPUT 2 PR PB Y/VIDEO R (MONO)/L R (MONO)/L AUDIO R INPUT 3 (MONO)/L VIDEO S-
VIDEO INPUT 3 R (MONO)/L VIDEO S-VIDEO R INPUT 4 AUDIO TO HI-FI (MONO)/L VIDEO S-VIDEO AUDIO TO HI-FI R INPUT 4 (MONO)/L
VIDEO S-VIDEO R L MONITOR OUT L VIDEO S-VIDEO L R MONITOR OUT L VIDEO S-VIDEO AUDIO AUDIO R R Model: 43FWX20B Audio Video
OUTPUT Models: 51/57UWX20B 51/57GWX20B Audio Video OUTPUT VCR VCR 15 CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A
STEREO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as
2. 3. 4. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. Connect the cable from the AUDIO
OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. Press the VID2~VID5 button to view the program from the VCR or laserdisc player.
The VIDEO label disappears automatically after approximately four seconds. Press the ANT button to return to the previous channel. 5. ANT A ANT A DVI-
HDTV PR INPUT 1 PB Y INPUT 1 PR PB Y TO CONVERTER R (MONO)/L AUDIO TO CONVERTER R (MONO)/L AUDIO PR ANT B INPUT 2 PB
Y/VIDEO ANT B AUDIO INPUT 2 PR PB Y/VIDEO R (MONO)/L R (MONO)/L AUDIO R INPUT 3 (MONO)/L VIDEO S-VIDEO INPUT 3 R (MONO)/L
VIDEO S-VIDEO R INPUT 4 AUDIO TO HI-FI (MONO)/L VIDEO S-VIDEO INPUT 4 AUDIO TO HI-FI R (MONO)/L VIDEO S-VIDEO R L MONITOR
OUT L VIDEO S-VIDEO L MONITOR OUT R L VIDEO S-VIDEO AUDIO AUDIO R R Model: 43FWX20B OUTPUT Models: 51/57UWX20B
manual of each component for the location of video and audio inputs and outputs.
VID1~VID5 button as necessary to view the input source.
shown on the TV set below.
51/57GWX20B OUTPUT R L V R L V VCR VCR NOTES: 1.
You're reading an excerpt. Click here to read official HITACHI
43FWX20B user guide
http://somemanuals.com/dref/317126