Operating Instructions; Before Turning "On; Turning "On; Using Remote Control - Uniflame TG546f Setup And User Manual

Operating Instructions

Note: Electric fireplace functions best WITHOUT an
extension cord.
If an extension cord is necessary:
• Use a UL approved, 3 prong plug (grounded)
cord shall be no. 14 AWG minimum size and
rated not less than 1,500 watts.
• Never connect two or more extension cords
together.
• Use the shortest extension cord possible.
• Keep connections dry and off the ground.
• Avoid draping the grill cord where children or
animals could encounter it.

Before Turning "ON"

1. Make sure all labels, packaging and protective films
have been removed from the electric fireplace.
2. Electric fireplace should be thoroughly inspected
before each use, and by a qualified service person at
least annually.

Turning "ON"

1. Make sure the main power switch (
"OFF" position. (Illustration 1)
2. Plug the power cord into a dry 120V GFI (Ground Fault
Interrupter) 3 plug outlet. (Illustration 2)
3. Push the main power switch to the "ON" position.
(Illustration 1).
4. Adjust flame control knob ( ) to the desired setting.
Note: If you do not want the flame, turn the flame control
knob to the twelve (12) o'clock position.
5. To turn the heat on, push the heat switch (
"ON" position.
6. Adjust the heat control knob ( ) to the desired
setting.
Note: If you do not want the heat, push the heat switch
to the "OFF" position.
Note: Fire log brightness can only be controlled by using
the remote. There are not separate controls for the fire
log brightness on the control panel.
Note: When the main power is turned on the fire log
brightness is factory set to medium brightness.

Using Remote Control

Note: Once the remote is used, the control panel knobs
are disabled.
Note: To enable the control panel knobs push the
main power switch on the control panel to the "OFF"
position, wait 5 seconds, then push the main power
switch to the "ON" position.
Note: The effective range of the remote control is up to
19.7 ft. (6 m).
1. Insert 2 AAA batteries (NOT INCLUDED) into the back
of the remote.
Note: Do NOT mix old and new batteries.
Note: Do NOT mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadium) batteries.
2. If the electric fireplace is unplugged:
a. Make sure the main power switch (
the "OFF" position. (Illustration 1)
b. Plug the power cord into a dry 120V GFI
(Ground Fault Interrupter) 3 plug outlet.
Heater Operation Instructions
(Illustration 2)
1. Plug the power cord into a dry 120V grounded outlet.
2. The main power (
work. Push the main power switch (
c. Push the main power switch to the "ON"
is in the ON position
3. Push the heater switch (
position. (Illustration 3).
the ON position.
4. Adjust the heater control knob (
setting.
If the electric fireplace is pluggen into a dry GFI outlet.
a. Push the main power switch to the "ON"
position. (Illustration 3).
Product size
Illustration 1
OFF
ON
) is in the
Main Power and flame control.
Illustration 2
) to the
Metal Screw
Metal Screw
Connecting the power cord to a
dry GFI 3 plug outlet.
Illustration 3
OFF
ON
Main Power and flame control.
Illustration 4
) is in
) must be ON for the heater to
) so the switch
) so the switch is in
) to your desired
Heat power and heat control.
Intdoor Electric Fireplace Model No. EF700SP
Cleaning and Care (continued)
3. To adjust the fire log brightness, press one of the log
button ( ):
"+" means more brightness
"–" means less brightness.
Note: Fire log brightness can only be controlled by using
the remote. There are not separate controls for the fire
log brightness on the control panel.
Note: When the main power is turned on the fire log
brightness is factory set to medium brightness.
4. To adjust the flame level, press one of the flame button
( ):
"+" means more brightness
"–" means less brightness.
5. To adjust the heat level, press the heat level
button ( ):
Note: the button will alternate between two preset
levels - HIGH and LOW.
6. Push the power button (
Main Power and Flame Operation Instructions
1. Plug the power cord into a dry 120V grounded outlet.
2. The main power ( ) must be ON for the heater to
Note: This does not turn the entire electric fireplace OFF, the electric fireplace is in the
work. Push the main power switch ( ) so the switch
is in the ON position
"standby mode".
3. Adjust the heater control knob ( ) to your desired
setting.

Turning "OFF"

1. Push the main power switch to the "OFF" position.
2. Unplug the power cord from the wall outlet.

Cleaning and Care

Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of electric fireplace.
3. Do not clean any electric fireplace part in a self cleaning oven. The extreme heat will
damage the finish.
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, ventilation openings of the electric fireplace be kept clean.
5. Inspect electric fireplace before each use.
6. Have electric fireplace inspected annually and repairs should be made by a qualified
service person.
7. Check electric fireplace immediately if any of the following conditions exist:
a. You see sparks around the electrical outlet, power cord or inside the fireplace.
b. Any part of the power cord is cut.
c. Any strange noise, smell or smoke.
8. Do not paint any part of the electric fireplace firebox.
9. This electric fireplace should be thoroughly checked and cleaned on a regular basis.
10. After a period of storage and/or non use, ventilation obstructions and inspect for any
abrasion, wear, cuts to the power cord.

Cleaning Surfaces

Main Power and Flame Operation Instructions
1. Plug the power cord into a dry 120V grounded outlet.
2. The main power ( ) must be ON for the heater to
1. Wipe surfaces clean with mild dishwashing detergent or baking soda.
work. Push the main power switch ( ) so the switch
is in the ON position
3. Adjust the heater control knob ( ) to your desired
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
setting.
3. Rinse clean with damp cloth.
Note: While cleaning your unit, be sure to keep the area around the heating element dry at all
times. Do not submerge the heating element assembly. If the heating element is submerged in
water, do NOT use it. It must be replaced.

Maintenance

To enjoy years of outstanding performance from your electric fireplace, make sure you perform
the following maintenance activities on a regular basis:
1. Keep exterior surfaces clean.
OFF
2. Air flow must be unobstructed. Keep circulating air passageways clean.
ON
Illustration 5
Infrared remote.
) to turn OFF.
OFF
ON