Page 1
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR. LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE ATTENTION TOUTE PARTICULIÈRE...
To obtain warranty service in the U.S. return the product, together with proof of purchase, to the U.S. Bostitch National or Regional Independent Authorized Warranty Service Center.
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool.
100 fasteners per minute. OPERATION BOSTITCH OFFERS THREE TYPES OF OPERATION FOR THIS SERIES TOOL. CONTACT TRIP: The common operating procedure on “Contact Trip” tools is for the operator to contact the work to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted.
Frequent, but not excessive, lubrication is required for best performance. Oil added through the air line connection will lubricate the internal parts. Use BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance.
Approximately 1/2" (13mm) NOTE: Use only staples recommended by Bostitch for the 600,700 & 800 Series staplers or staples which meet Bostitch specifications. Always disconnect air supply: 1. Before making adjustments; 2. When servicing the tool;...
READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are three available systems on BOSTITCH pneumatic tools. They are: 1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION OPERATION 1.
OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.
“O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing.
Loosen screw as shown. Adjust to desired exhaust direction and tighten screw. QUICK RELEASE MAGAZINE The 600,700 & 800 series staplers contain a Quick Release Magazine feature. The magazine is spring loaded to reduce jamming. When a jam does occur, a quick release mechanism at the rear of the magazine allows the magazine to move back, in order to clear the jam.
Page 12
GARANTÍA LIMITADA — Sólo EE.UU. y Canadá A partir del 1 de diciembre de 2005 Bostitch, L.P. garantiza al comprador del comerciante original que el producto comprado está exento de defectos en material y fabricación, y se compromete a reparar o reemplazar, a opción de Bostitch, cualquier engrapadora o clavadora neumática defectuosa de marca Bostitch por un período de siete (7) años...
INSTRUCCIONES DE SEGURIDAD Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LATERALES.
100 grapas por minuto. OPERACIÓN BOSTITCH OFRECE TRES TIPOS DE OPERACIÓN PARA HERRAMIENTAS DE ESTA SERIE DISPARO POR CONTACTO: El procedimiento de operación común para las herramientas de “Disparo por Contacto” es que el operador hace contacto con el objeto a ser clavado para activar el mecanismo de disparo, manteniendo halado el gatillo.
Use el Lubricante de Herramientas de Aire Mobil Velocite #10 de BOSTITCH o un equivalente. No use aceite detergente o aditivos, ya que estos lubricantes causan el desgaste acelerado de los sellos y los amortiguadores de choque en la herramienta, dando como resultado un mal rendimiento de la herramienta y el mantenimiento frecuente de la misma.
13 mm (1/2"). cargador. NOTA: Use solamente las grapas recomendadas por Bostitch para las engrapadoras de las series 600, 700 y 800 o grapas que cumplan con las especificaciones de Bostitch. Siempre desconecte el suministro de aire: 1. antes de efectuar ajustes; 2. al dar servicio a la herramienta;...
II. CONSULTE “ESPECIFICACIONES DE LA HERRAMIENTA” EN ESTE MANUAL PARA IDENTIFICAR EL SISTEMA OPERATIVO DE SU HERRAMIENTA. Se dispone de tres sistemas operativos para las herramientas neumáticas de BOSTITCH. Éstos son: 1. OPERACIÓN POR GATILLO 2. OPERACIÓN DE DISPARO POR CONTACTO 3.
Page 18
• Jamás deje una herramienta sola con la manguera de aire conectada. • NOTA: No siga usando una herramienta que tenga una fuga de aire o que no funciona debidamente. Notifique a su representante de BOSTITCH más cercano si su herramienta sigue teniendo problemas de funcionamiento.
PARTES DE REEMPLAZO: Se recomienda partes de reemplazo de BOSTITCH. No utilice partes modificadas ni partes que no brinden el mismo rendimiento que el equipo original. PROCEDIMIENTO DE ENSAMBLE PARA LOS SELLOS: Al reparar una herramienta, asegúrese de que las partes internas estén limpias y lubricadas.
Impulsor roto/quebrado....Reemplazar el impulsor. (Verificar el anillo en O del pistón). Cargador seco/sucio.....Limpiar/Lubricar. Utilice Lubricante para Herramientas Neumáticas de BOSTITCH.
Lubricante Bostitch Air -Tool de 1 pinta (470 ml) para herramientas neumáticas BC603 Lubricante Bostitch “Winter-Formula” de 1 pinta (470 ml) para herramientas neumáticas BC604 Lubricante Bostitch Air -Tool de 1 cuarto de galón (940 ml) para herramientas neumáticas 100653 Lubricante para juntas tóricas (2cc) 851325 LOCTITE Grade 271 (0.02 oz.
Page 22
GARANTIE LIMITÉE – É.-U. et Canada seulement À partir du 1er décembre 2005, Bostitch, L.P. garantit à l’acheteur d’origine au détail que ce produit est exempt de tout défaut de matériaux et de fabrication et accepte, le cas échéant, de réparer ou de remplacer, à la discrétion de Bostitch, toute agrafeuse ou cloueuse de marque Bostitch défectueuse pour une période de sept (7) ans à...
CONSIGNES DE SÉCURITÉ UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
100 agrafes par minute. OPÉRATION BOSTITCH OFFRE TROIS SYSTÈMES DE DÉCLENCHEMENT POUR CETTE SÉRIE DÉCLENCHEMENT À LA VOLÉE : Le mode opératoire ordinaire pour le système « à la volée » consiste pour l’opérateur à placer le nez de l’appareil sur la surface de travail pour activer l’élément palpeur tout en appuyant sur la détente, enfonçant ainsi un élément d’assemblage...
éléments internes. Utiliser le lubrifiant pour outils pneumatiques Mobil Velocite n° 10 de BOSTITCH ou un équivalent.Ne pas utiliser une huile détergente ou des additifs qui pourraient accélérer l’usure des joints toriques et des amortisseurs du cloueur et par conséquent entraîner une baisse du rendement et des réparations plus fréquentes.
Environ 13 mm (1/2 po). REMARQUE : Utilisez uniquement les agrafes recommandées par Bostitch pour les agrafeuses des séries 600, 700 et 800 ou des agrafes répondant aux spécifications de Bostitch. Toujours désaccoupler l’appareil de sa source d’énergie : 1) avant tout réglage; 2) lors de l’entretien;...
II. SE RÉFÉRER À LA RUBRIQUE « CARACTÉRISTIQUES DE L’APPAREIL » DU MANUEL AFIN D’IDENTIFIER LE MODE D’UTILISATION DE VOTRE OUTIL. Il existe trois modes d’utilisation pour les outils pneumatiques BOSTITCH : 1. DÉCLENCHEMENT PAR DÉTENTE 2. DÉCLENCHEMENT À LA VOLÉE 3.
Page 28
• Porter toujours l’outil par la poignée, jamais par le nez. • Ne pas altérer ou modifier cet outil par rapport à sa forme originale sans l’agrément de BOSTITCH, INC. • Toujours avoir présent à l’esprit qu’une manipulation ou une utilisation inadéquate de cet outil peuvent causer des blessures.
LUBE sur toutes les pièces mobiles et pivots. Les opérations de remontage terminées, veiller à mettre quelques gouttes de lubrifiant pour outils pneumatiques BOSTITCH dans le circuit d’air avant de procéder aux essais. ALIMENTATION D’AIR - PRESSION - VOLUME : Le volume d’air est aussi important que la pression.