Table of Contents
Advertisement
section
•
( Connecting the units
)
c
)
About suitable
specification of speaker
Ensure speakers conform to the following
standards, otherwise there is a risk of fire,
smoke or damage. Speaker impedance is 2
n
to 8
n,
or 4
n
to 8
n
for two-channel and other
bridge connections.
•
Never band together multiple speaker'snega-
tive cables.
•
If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch (12 V DC), the amplifier will re-
main on with the ignition whether the car
stereo is on or off, which may exhaust battery
if the engine is at rest or idling.
•
Install and route the separately sold battery
wire as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away as possible from the anten-
na, antenna cable and tuner.
C!J
About bridged mode
Subwoofer
Four-channel output
Two-channel output
Th ree-chan nel
Speaker output A
Nominal input:
Min,75W
Nominal input:
Min,200W
Nominal input:
Min,75W
Other than subwoofer
Diagram A- Proper
Pioneer
Amplifier
4
Q
Bridged
Mode
Diagram B- Improper
2
Q
Bridged
Mode
Three-channel
Speaker output B
Four-channel output
Two-channel output
Nominal input:
Min,200W
Max. input:
Min. 150W
Max. input:
Min,400W
Connecting the speakers
The speaker output mode can be four-channel,
three-channel (stereo and mono) or two-chan-
nel (stereo or mono), Connect the speaker
leads based on the mode and the figures
shown below.
Speaker impedance is max. 4
n,
please carefully
check. Improper connection to the amplifier may
result in malfunction or personal injury due to
burns from overheating.
For bridged mode for a two-channel amplifier,
with a 4.n load, either wire two 8.n speakers in
parallel, Left
®
and Right
8
(Diagram A) or use a
single 4.n speaker, For other amplifiers, please
follow the speaker output connection diagram for
bridg ing shown on rear: two 8.n speakers in par-
allel for a 4.n load or a single 4.n speaker per
channel.
For any further enquiries, contact your local
authorized Pioneer dealer or customer service,
C!J
CD
En
Three-channel
Speaker output A
Three-channel
Speaker output B
Max. input:
Min. 150W
Max. input:
Min.400W
section
•
( Connecting the units
)
c
)
About suitable
specification of speaker
Ensure speakers conform to the following
standards, otherwise there is a risk of fire,
smoke or damage. Speaker impedance is 2
n
to 8
n,
or 4
n
to 8
n
for two-channel and other
bridge connections.
•
Never band together multiple speaker'snega-
tive cables.
•
If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch (12 V DC), the amplifier will re-
main on with the ignition whether the car
stereo is on or off, which may exhaust battery
if the engine is at rest or idling.
•
Install and route the separately sold battery
wire as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away as possible from the anten-
na, antenna cable and tuner.
C!J
About bridged mode
Subwoofer
Four-channel output
Two-channel output
Th ree-chan nel
Speaker output A
Nominal input:
Min,75W
Nominal input:
Min,200W
Nominal input:
Min,75W
Other than subwoofer
Diagram A- Proper
Pioneer
Amplifier
4
Q
Bridged
Mode
Diagram B- Improper
2
Q
Bridged
Mode
Three-channel
Speaker output B
Four-channel output
Two-channel output
Nominal input:
Min,200W
Max. input:
Min. 150W
Max. input:
Min,400W
Connecting the speakers
The speaker output mode can be four-channel,
three-channel (stereo and mono) or two-chan-
nel (stereo or mono), Connect the speaker
leads based on the mode and the figures
shown below.
Speaker impedance is max. 4
n,
please carefully
check. Improper connection to the amplifier may
result in malfunction or personal injury due to
burns from overheating.
For bridged mode for a two-channel amplifier,
with a 4.n load, either wire two 8.n speakers in
parallel, Left
®
and Right
8
(Diagram A) or use a
single 4.n speaker, For other amplifiers, please
follow the speaker output connection diagram for
bridg ing shown on rear: two 8.n speakers in par-
allel for a 4.n load or a single 4.n speaker per
channel.
For any further enquiries, contact your local
authorized Pioneer dealer or customer service,
C!J
CD
En
Three-channel
Speaker output A
Three-channel
Speaker output B
Max. input:
Min. 150W
Max. input:
Min.400W
Advertisement
Table of Contents
