Download
 Share
 Print this page
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Car Amplifier
  5. GM-D9500F
  6. Owner's manual

Before Installing The Amplifier; Example Of Installation On The Floor Mat Or Chassis - Pioneer GM-D9500F Owner's Manual

Bridgeable four-channel power amplifier
Hide thumbs

Advertisement

section
('--
~)
CI
(' - -I_ns_t_a_lIa_t_io_n
~)
Before installing the amplifier
AWARNING
•
Do not use unauthorized parts as this may
cause malfunctions.
•
Do not install this unit where:
-
it may interfere with operation of the vehi-
cle.
-
it may cause injury to a passenger as a re-
sult of a sudden stop.
•
Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the car, which can result in fire,
•
Place all cables away from moving parts, such
as the gear shift and seat rails.
•
When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
A
CAUTION
• To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
-
Allow adequate space above the amplifier
for proper ventilation.
-
Do not cover the ampl ifier with a floor mat
or carpet.
•
Place all cables away from hot places, such
as near the heater outlet.
• The optimal installation location differs de-
pending on the car model. Secure the ampli-
fier at a sufficiently rigid location.
• Check all connections and systems before
final installation.
• After installing the amplifier, confirm that the
spare tire, jack and tools can be easily re-
moved.(!)
Example of installation on
the floor mat or chassis
1
Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm x
18 mm) into the screw holes and push on the
screws with a screwdriver so they make an im-
print where the installation holes are to be lo-
cated.
2
Drill 2.5
mm (1/8 in.) diameter holes at
the imprints either on the carpet or directly
on the chassis.
3
Install the amplifier with the use of
supplied tapping screws (4 mm)( 18 mm).
CD
Tapping-screws (4 mm x 18 mm)
®
Drill a 2.5 mm (1/8 in.) diameter hole
®
Floor mat or chassis (!)
-
m
::s
ee.
iii"
::so
En
®
section
('--
~)
CI
(' - -I_ns_t_a_lIa_t_io_n
~)
Before installing the amplifier
AWARNING
•
Do not use unauthorized parts as this may
cause malfunctions.
•
Do not install this unit where:
-
it may interfere with operation of the vehi-
cle.
-
it may cause injury to a passenger as a re-
sult of a sudden stop.
•
Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the car, which can result in fire.
•
Place all cables away from moving parts, such
as the gear shift and seat rails.
•
When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
A
CAUTION
• To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
-
Allow adequate space above the amplifier
for proper ventilation.
-
Do not cover the ampl ifier with a floor mat
or carpet.
•
Place all cables away from hot places, such
as near the heater outlet.
• The optimal installation location differs de-
pending on the car model. Secure the ampli-
fier at a sufficiently rigid location.
• Check all connections and systems before
final installation.
• After installing the amplifier, confirm that the
spare tire, jack and tools can be easily reo
moved.(!)
Example of installation on
the floor mat or chassis
1
Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm x
18 mm) into the screw holes and push on the
screws with a screwdriver so they make an im-
print where the installation holes are to be lo-
cated.
2
Drill 2.5
mm (1/8 in.) diameter holes at
the imprints either on the carpet or directly
on the chassis.
3
Install the amplifier with the use of
supplied tapping screws (4 mm)( 18 mm).
CD
Tapping-screws (4 mm x 18 mm)
®
Drill a 2.5 mm (1/8 in.) diameter hole
®
Floor mat or chassis (!)
-
m
::s
ee.
iii"
::so
En
®

Advertisement

loading

  Also See for Pioneer GM-D9500F

Pioneer GM-D9500F Owner's Manual
Pioneer GM-D9500F Owner's Manual 52 pages
Pioneer GM-D9500F Owner's Manual
Pioneer GM-D9500F Owner's Manual 44 pages

  Related Manuals for Pioneer GM-D9500F

  Related Content for Pioneer GM-D9500F