Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Abocom USB 10/100M Fast Ethernet UFE1500
Summary of Contents for Abocom USB 10/100M Fast Ethernet UFE1500
-
Page 1: Fast Ethernet
10/100M FAST ETHERNET Installation Guide M73-APO08-540... -
Page 2: Regulatory Statements
REGULATORY STATEMENTS FCC Certification Part15, Class B The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. FCC Part 15 Registration This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interface, and This device must accept any interface received,... -
Page 3: Specifications
INTRODUCTIONS The USB 10/100M Fast Ethernet Adapter provides outside-the-box plug-and-play local area network connections for USB-enabled PCs, notebooks and laptops. This adapter uses a B type USB port to connect with the USB host, and an RJ-45 port to connect with a 10/100 Fast Ethernet LAN link. - Page 4 Operation: 111mA (max) Sleep Mode: 3.9 mA (max) Parts Names and Functions USB Type A plug: connects the USB host port to the USB 10/100M Fast Ethernet Adapter. USB Fast Ethernet Adapter 10/ACT LED indicator: glows green when 10M Network is linked; blinks green when the Fast Ethernet Adapter is transmitting/ receiving data.
-
Page 5: Installation
INSTALLATION Precaution Before the installation, make sure the USB port exists in your computer and is enabled. To check this, Panel System. Open the Device Manager tab. If the Universal Serial Bus controller device is found, it means your USB port is installed and enabled. - Page 6 2. Connect the UTP cable to the Fast Ethernet Adapter. 3. Connect the other end to a Hub. - 4 -...
-
Page 7: Software Installation
SOFTWARE INSTALLATION Installation for Windows 98 Once the device is properly connected to your automatically detect the new hardware device. Perform the following procedures for installing the device driver. Insert the device driver disk into your floppy drive. When the above figure appears, click Next. - Page 8 The installation program will proceed automatically. instruction to finish. When Windows prompts you to restart your computer, click No to make some changes to your network settings. Follow - 6 - on-screen...
- Page 9 Go to Start Double-click Network. When the Network dialog box appears, select USB 10/100M Fast Ethernet and click Add. Set the appropriate protocols and client for you needs. When completed, click OK. Remember to restart your computer to activate the new device Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start...
-
Page 10: Installation For Windows 2000
Adapter is found, it means that your device is properly installed and enabled. Installation for Windows 2000 1. Once the device is well connected to your computer, Windows 2000 will automatically detect the new device. proceed. Click Next to - 8 -... - Page 11 2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the new device driver to the disk drive. Select Floppy disk drives. Click Next. 4. Click Next. necessary files to your system. 5. Click Yes to continue. 6.
- Page 12 7. Go to Start Network and Dial-up Connections. Double-click Local Area Connections. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK. Settings Control Panel - 10 -...
- Page 13 9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Control Panel the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled.
- Page 14 Click Next to continue. Click Next. Windows will copy all the necessary files to your system. - 12 -...
- Page 15 Click Finish to complete the software installation. When asked if you want to restart your computer, click No to continue the Network configuration. Go to Start Double-click Network. When the Network dialog box appears, select USB 10/100 Network Adapter and Settings Control Panel.
-
Page 16: Installation For Windows Xp
click Add. Set the appropriate protocols and client for you needs. When completed, click OK. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Control Panel Manager tab. - Page 17 Insert the device Driver Disk into the floppy disk drive of your system. Select Search removable media (floppy, CD- ROM…) and click Next. Click Next to continue. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click Continue Anyway to proceed.
- Page 18 Wait for seconds while Windows copies the appropriate driver to your system. Click Finish. The software installation for this network device is now completed. Go to Start Network and Dial-up Connections. Double-click Local Area Connections. Settings Control Panel - 16 -...
- Page 19 When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start System.
- Page 20 - 18 -...