Table of Contents
Advertisement
Quick Links
BLK-CPB700R Series High Performance
IR Bullet Camera User Manual
Products: BLK-CPB700R65, BLK-CPB700R150, BLK-CPB700R300
Please read this manual before using your camera, and always follow the instructions for
safety and proper use. Save this manual for future reference.
BLK-BulletCameras-2_CM
12/17/2013
Advertisement
Table of Contents
Related Manuals for Black Line BLK-CPB700R65
Summary of Contents for Black Line BLK-CPB700R65
- Page 1 BLK-CPB700R Series High Performance IR Bullet Camera User Manual Products: BLK-CPB700R65, BLK-CPB700R150, BLK-CPB700R300 Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference. BLK-BulletCameras-2_CM 12/17/2013...
- Page 2 Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. WARNING To prevent electric shock and risk of fire hazards, do NOT use other than the specified power source. CAUTION REGULATORY NOTICE This device complies with Part 15 of the FCC Rules.
-
Page 3: Table Of Contents
BLK-CPB700R65 ........ - Page 4 Precautions This camera should be installed by qualified personnel only. • There are no user serviceable parts inside. • Do not disassemble this camera other than to make initial adjustments. • Use a UL approved regulated 24 volt AC or 12 volt DC power supply. •...
-
Page 5: Introduction
SECTION 1: INTRODUCTION SECTION 1 Introduction These high performance indoor/outdoor IR bullet cameras feature a very high resolution Sony 960H CCD sensor providing 700 TVL, ® with True Day & Night capability, dual voltage range (24 Vac, 12 Vdc), and on-screen display (OSD) for control and setup. 1.1 Features High resolution: color - 700 TV lines •... - Page 6 SECTION 1: INTRODUCTION BLK-CPB700R65 camera BLK-CPB700R150 camera BLK-CPB700R300 camera ∞ Far-Near ( 1 N), Tele-Wide (T 1 N) controls lens and OSD controls 1.1.1 What’s in the box Your camera includes the following: Four (4) coarse-threaded screws to secure the base plate •...
- Page 7 SECTION 1: INTRODUCTION 1.1.2 Tools you need To install the camera, you will need: 12 Vdc or 24 Vac power source • Tools for mounting the camera • Video and power extension cables, if needed • Hand-held CCTV video setup monitor (optional) •...
-
Page 8: Installation
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR array shield becomes • soiled, clean it only with approved products. See the Cleaning section later in this manual. Monitor impedance: Set the monitor impedance switch to 75Ω. -
Page 9: Camera Adjustments
If using a hand-held CCTV video setup monitor with your camera: Remove the cover to the OSD control panel by unscrewing it counter clockwise. BLK-CPB700R65 OSD Controls BLK-CPB700R150 and BLK-CPB700R300 OSD Controls Connect the BNC adapter cable to the VIDEO TEST port on the OSD control panel. - Page 10 The LED LEVEL is preset at the factory. However, an adjustment screw is provided on the OSD panel of the BLK-CPB700R150 and BLK-CPB700R300 cameras for environments where the image brightness in dark conditions is still not satisfactory after performing a Software Setup of the camera. The LED LEVEL of the BLK-CPB700R65 camera is not adjustable.
- Page 11 SECTION 2: INSTALLATION To adjust the LED LEVEL of a BLK-CPB700R150 or BLK-CPB700R300 camera: WIth the camera operating in a dark environment, unscrew the OSD panel access cover to access the OSD controls. While observing the video image from the camera, use a screwdriver to turn the LED LEVEL screw to counter- clockwise to brighten the image, and/or clockwise to darken the image until the image brightness is acceptable.
-
Page 12: Software Setup
Configuration settings are made using the OSD control panel, located on the underside of the camera. Unscrew the cover to access the controls. Depending on the model of your camera, the OSD control panel may appear as one of the following: BLK-CPB700R65 OSD Controls BLK-CPB700R150 and BLK-CPB700R300 OSD Controls Use the SETUP joy stick on the OSD control panel to navigate through the menu system. -
Page 13: Exposure
SECTION 3: SOFTWARE SETUP MODE: Rock the joystick down to highlight MODE. Rock the joystick left or right do display INDOOR or OUTDOOR (installation environment). RETURN: To return to the SETUP menu and save your brightness and mode settings, rock the joystick down to highlight RETURN, then press it in to select return. - Page 14 SECTION 3: SOFTWARE SETUP The SENSE-UP feature is only available when the SHUTTER option is set to AUTO or 1/60 (DC LENS). When SENSE-UP is activated, NOTE the increased magnification can induce noise and pixilation. SENSE-UP: Rock the joystick left or right to observe the optimal screen brightness in low light conditions. Select a multiplier between x2 ~ x256.
- Page 15 SECTION 3: SOFTWARE SETUP After selecting the AREA graphical submenu, a POSITION screen opens. Rock the joystick up, down, left and/ — or right to position the upper-left corner of the BLC area, then push the joystick in to confirm your selection and enter the SIZE graphical submenu.
-
Page 16: White Bal
SECTION 3: SOFTWARE SETUP D-WDR: The D-WDR feature employs intelligent light level control to compensate for strong backlight conditions. D-WDR Off D-WDR ON OFF: The D-WDR function is disabled. INDOOR: The D-WDR is preset with default LOW-LEVEL and HIGH-LEVEL settings for normal indoor lighting condition. These settings can be adjusted in the INDOOR sub-menu. -
Page 17: Day/Night
If white balance adjustments don’t perform well, use AWB mode. 3.4 DAY/NIGHT The DAY/NIGHT feature is used to configure the camera to provide images in color, black and white, or either depending on lighting conditions. High Performance IR CCTV Bullet Camera User Manual... - Page 18 SECTION 3: SOFTWARE SETUP EXT: This feature is not used in these cameras. B/W: The picture is displayed in black and white only. When B/W is used, WHITE BAL is disabled. Selecting this option opens the B/W sub-menu. BURST: Burst ON sends a color signal to the monitor in B/W mode. This signal does degrade the clarity of the image from the camera.
-
Page 19: 3Dnr
SECTION 3: SOFTWARE SETUP POSITION SIZE In the SIZE graphical submenu, rock the joystick up or down to raise or lower the bottom edge of the AREA. Rock — the joystick left and/or right to contract or expand the AREA horizontally. Press the joystick in twice to return to the IR SMART menu. -
Page 20: Special
SECTION 3: SOFTWARE SETUP ON: Activates the noise reduction feature. Selecting this option opens the 3DNR sub-menu where the level of noise reduction can be adjusted. LEVEL: With the cursor pointed at the LEVEL, rock the joystick left or right to decrease or increase the level of noise reduction. - Page 21 SECTION 3: SOFTWARE SETUP On the camera title screen: To enter a character in the title at the cursor position, rock the joystick up, down, left and right to highlight a character — (0 - 9, A - Z, u - .). The character under the cursor and the bar under the character position title both blinks slowly. Press the joystick in to select the character and move to the next character position.
- Page 22 SECTION 3: SOFTWARE SETUP MIRROR (off) MIRROR D-EFFECT selected D-ZOOM: D-ZOOM allows you to zoom in on a portion of the image by first setting the digital zoom magnification (x1 ~ x32), and then using the PAN and TILT controls to move to the area of the image you want to see. When D-ZOOM is used, SMART DZOOM and DIS are disabled.
- Page 23 DIS off DIS on NEG. IMAGE: Set this option to ON to show a color-reversed or black and white-reversed image. RETURN: On the D-EFFECT menu, select RETURN to return to the SPECIAL menu. MOTION: The MOTION feature allows you to quickly identify areas of the image where motion is detected. Set MOTION to ON then press the joystick in to open the MOTION sub-menu.
- Page 24 SECTION 3: SOFTWARE SETUP VALUE (sensitivity): VALUE allows you to select the camera sensitivity to movement in the area selected. The higher the setting value is, the higher the sensitivity to movement. MOTION VIEW: This feature is used to highlight objects found moving in motion detection areas. OFF.
- Page 25 SECTION 3: SOFTWARE SETUP SENSE-UP: Use this option to set the sensitivity for finding defects. The higher the value of “SENS UP”, the more defects will be compensated. Setting this level to x64 or x32 produces the best results. DIFF: Use this option to set the defect size from 1 to 3. The higher the DIFF value, the brighter the defects it will detect. Lower DIFF values detect fainter defects.
-
Page 26: Adjust
SECTION 3: SOFTWARE SETUP GAMMA can be set to 0.05 to 1.00 in increments of 0.05, or set to USER (default). Select the GAMMA level to produce — the best image on the monitor. NOTE: If you replace the monitor, you may need to change the GAMMA setting. RETURN: Select RETURN to return to the SPECIAL menu. -
Page 27: Reset
SECTION 3: SOFTWARE SETUP 3.8 RESET Use RESET to revert the camera configuration settings to the factory default values. FACTORY: Select FACTORY to reset the camera configuration. RETURN: Rock the joystick to select RETURN, to return to the SETUP menu. 3.9 EXIT Select EXIT to close the SETUP menu. -
Page 28: Cleaning
SECTION 4: CLEANING SECTION 4 Cleaning Clean the camera dome with an approved glass cleaning solution and a lint free cloth. Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft •... -
Page 29: Specifications
SECTION 5: SPECIFICATIONS SECTION 5 Specifications Table 1. Component specifications Component BLK-CPB700R65 BLK-CPB700R150 BLK-CPB700R300 Sensor type 1/3” Sony 960H CCD Effective pixels 976 (H) × 494 (V) approx. 480K pixels Total pixels 1020 (H) × 508 (V) approx. 520K pixels... - Page 30 SECTION 5: SPECIFICATIONS Component BLK-CPB700R65 BLK-CPB700R150 BLK-CPB700R300 Storage temperature, humidity -4 ºF ~ 140 ºF (-20 ºC ~ +60 ºC), humidity: 20 % RH ~ 95 % RH Operating temperature, 14 ºF ~ 122 ºF (-10 ºC ~ +50 ºC), humidity : 20 % RH ~ 80 % RH humidity 2.87 in ×...
-
Page 31: Appendix A Troubleshooting
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting Problem Possible Cause Nothing appears on the screen - Check the power connection. - Check the video signal cable connection to the monitor. The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth. - Adjust the monitor controls, if necessary. -
Page 32: Appendix B Camera Dimensions
APPENDIX B: CAMERA DIMENSIONS APPENDIX B Camera Dimensions BLK-CPB700R65 8.03” 180° 360° 360° Side 2.87” Front... -
Page 33: Blk-Cpb700R150
APPENDIX B: CAMERA DIMENSIONS BLK-CPB700R150 8.98” 180° 360° 360° 3.31” Front High Performance IR CCTV Bullet Camera User Manual... -
Page 34: Blk-Cpb700R300
APPENDIX B: CAMERA DIMENSIONS BLK-CPB700R300 11.42” Side 7.41” 360° 180° 360° 6.30” 3.94” Front 3.46”...
Need help?
Do you have a question about the BLK-CPB700R65 and is the answer not in the manual?
Questions and answers
is this camera TAA compliance