Table of Contents
Advertisement
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V
AC, 50 Hz.
Then the standby LED lights up.
To switch on the TV from standby mode
either:
Press the "
o
P/CH+ or a numeric button on the
remote control.
Press the control switch left side of
o
the TV. The TV will then switch on.
Note:
If you switch on your TV via CH- or CH+ buttons on the
remote control or on the TV set, the program that you
were watching last will be reselected.
By either method the TV will switch on.
To Switch the TV Off
Press the "
" button on the remote
control or hold the control switch on the
TV until shut down , so the TV will switch
to standby mode.
To power down the TV completely, unplug
the power cord from the mains socket.
Note:
When the TV is switched to standby mode, the standby
LED can blink to indicate that features such as Standby
Search, Over Air Download or Timer is active.
First Time Installation
When turned on for the first time, language selection
screen is displayed in all language options listed
alphabetically. Press the "
highlight the required language, press OK button to
select. "First Time Installation" appears. Use "
►
"
" button to set the required country, and press
▼
"
" button to select Search Type. Use "
►
"
" to set the desired Search Type. Available
search types are Digital and analog, digital only and
analog only. When set, press "
◄
Language. Use "
" or "
Language. Next, select Scan Encrypted and set as Yes
if you want to scan coded stations. Press OK button
on the remote control to continue and the search
type screen will be displayed. You must select a
Studio 19HFL2807D/10
" button, P/CH- or
▼
▲
" or "
" button to
◄
" or
◄
" or
▼
" to select Teletext
►
" to select Teletext
search type to search and store broadcasts from the
desired source.
IMPORTANT:
When you select Country option as France or Italy,
you will be asked to set and confirm a PIN number.
Selected PIN number cannot be 0000. Enter a PIN
number and confirm it by entering once more. Press
OK button to continue. If the two PIN numbers
match, your master PIN number will be set.
WARNING:
When you are required to enter a PIN number for
any menu operation you should use the PIN that you
have previously defined during the first time
installation. If you have forgotten the PIN number
you have set during the first time installation, you
should use the master PIN code, 4725.
Aerial Installation
If you select AERIAL option from the Search Type
screen, the television will search for digital terrestrial
TV broadcasts.
NOTE: You can press "MENU"button to cancel.
After all the available stations are stored, Channel
List will be displayed on the screen. If you like the
sort channels, according to the LCN (*), please
select "Yes" and then press OK.
Press "MENU" button to quit channel list and watch TV.
(*) LCN is the Logical Channel Number system that
organizes available broadcasts in accordance with a
recognizable channel sequence (if available).
Cable Installation
If you select CABLE option from the Search Screen,
press OK button on the remote control to continue.
To continue, please select YES and press OK. To
cancel operation, select NO and press OK. You can
select frequency ranges from this screen. For
highlighting lines you see, use "▼" or "▲" button.
You can enter the frequency range manually by using
the numeric buttons on the remote control. Set
Start and Stop Frequency as desired by using the
numeric buttons on the remote control. After this
operation, you can set Search Step as 8000 KHz or
1000 KHz. If you select 1000 KHz, the TV will
perform search process in a detailed way. Searching
duration will thus increase accordingly. Depending on
your Country selection in the first time installation,
250KHz search step option might be available on
Network Channel Scan screen. Note that if you
perform the search with 250KHz option,
P a g e
| 11
Advertisement
Table of Contents
