Table of Contents
Advertisement
Hotpoint recommends, for your own safety and to ensure you get the best possible results from your Washer
Dryer, you read through this booklet and follow these steps thoroughly.
STEP 1
Electrical Guide
Choose a location for your washer dryer,
where possible on a solid floor, with the
electrical sockets and water supply taps
Allow sufficient space: 600mm width,
600m depth and 900mm height.
DO NOT install in a bath or shower
WARNING: This appliance must be earthed.
STEP 3
Dispenser Drawer
Read through this section to familiarise
yourself with the different
compartments within the dispenser
Hotpoint recommend the Persil range of
NOTE: Always follow manufacturer's dosage
STEP 5
Options Guide
All available optional wash features are
explained within this section - These
allow you to adjust your selected wash
programme to suit your needs.
NOTE: In addition to the temperature of the
incoming water, the selection of optional wash
features will affect the programme times.
STEP 7
Wash & Auto Dry Programme
A picture guide provides a clear
explanation how to set a wash and auto
DO NOT overload the washer dryer.
NOTE: Hotpoint recommend, on completion of
your programme, that you switch off both the
electricity and water supply to the appliance.
Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.
INSTRUCTIONS FOR INSTALLATION & USE
easily accessible.
room.
drawer.
detergent products.
recommendations.
dry programme.
Keep these instructions in a safe place for quick reference.
WD72, WDM73
STEP 2
STEP 4
STEP 6
STEP 8
READ BEFORE
CONTACTING
SERVICE!
Installation Guide
Dispose of packaging material in a safe
place and remove any labels.
Please read through thoroughly to
ensure you understand each stage
before you begin.
Remember you may be charged for a service call if a
problem with your washer dryer is caused by
incorrect installation or misuse.
Wash Guide
A wash chart is provided to help you to
select your required programme.
Examples given for the maximum
washing load weight for different fabric
types.
Drying Guide
A guide to drying times is provided for
independent drying programmes, along
with a list of items not suitable for
tumble drying.
Examples given for the maximum drying
load weight for different fabric types.
NOTE: Always make sure the mains button is in the
OFF position before selecting an independent
drying programme.
Troubleshooting
Please refer to the Troubleshooting
section if you have any problems when
using your washer dryer.
There may be nothing wrong!
Advertisement
Table of Contents
Related Manuals for Hotpoint WD72
Summary of Contents for Hotpoint WD72
- Page 1 INSTRUCTIONS FOR INSTALLATION & USE Hotpoint recommends, for your own safety and to ensure you get the best possible results from your Washer Dryer, you read through this booklet and follow these steps thoroughly. STEP 1 Electrical Guide Choose a location for your washer dryer,...
-
Page 2: Hotpoint Guarantee
Republic of Ireland: 1850 502 200 Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover plans to give you total peace of mind. Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the period of cover. -
Page 3: Washing Weight Loads
STEP 4 IMPORTANT INFORMATION: The temperature of the incoming water supply and selection of any Optional Wash Feature will affect the programme times. ITCL Codes Fabric White Cotton & Linen without special finishes. Colourfast cotton, linen or viscose without special finishes 60 Non-colourfast cotton, linen &... -
Page 4: Variable Spin
STEP 5 Cancel Button To start the selection again, press and hold the cancel button for a few seconds, all settings displayed will disappear and the Infobubble™ will display ‘Select Programme’ . NOTE: If pressed when setting ‘Time Delay’ or when time delay is active, time delay is cancelled but the selected wash programme and optional wash features will remain, the Infobubble™... -
Page 5: Drying Weight Loads
STEP 6 Fabric Items Not Suitable Type for Tumble Drying: Garments with the ITCL Natural code - DO NOT TUMBLE DRY. Woollens. Synthetic Large bulky items eg. quilts, bedspreads, pillows etc... expand when dry, preventing air IMPORTANT INFORMATION: A 10 minute ‘Cool Tumble’ phase at the end of flow through the each drying cycle allows fabrics to gently cool down, minimising creasing. - Page 6 STEP 7 Switch on both the Sort laundry by label water and electricity into groups with the supply at the mains. same wash & dry requirements, load the appliance. See Drying Weight Load examples (STEP 6) Select optional wash programme (STEP 4), you will hear a beep and the Infobubble™...
-
Page 7: Washcare Tips
STEP 8 Washcare Tips: Before washing: Pre-treat stains. Close zips, tie belts, strings etc... and press studs to prevent tangling. Remove papers or tissues from pockets. Remove sharp objects and coins from pockets as they could cause damage to clothes or the appliance. -
Page 8: Error Codes
MY MACHINE IS LEAKING (E10/E11/E13) Are the fill hoses on correctly? If not tighten them. standpipe tions free Is your water pressure too high? selected? Turn the main supply tap down. Is the standpipe or household drain blocked. You may need to call in a plumber. -
Page 9: Appliance Overview
Wash Programme Buttons Dispenser Drawer Adjustable Feet RED line indicates the minimum height for the drainage hose. Hot Water inlet point and supplied Hose (Red or Grey end) Cold Water inlet point and supplied Hose (Blue end) Mains Cable Drainage Hose Retaining Flaps Cleaning the Exterior: Use a damp cloth or silicon polish to clean the exterior surfaces of the... -
Page 10: Electricity Supply
WARNING: Do not use plug unless fuse holder is in locked position. Changing the Mains Lead A special lead can be ordered from Hotpoint Service UK: 08709 066 066 or Republic of Ireland: 1850 302 200 If you have damaged the existing lead or require a longer one a charge will be made. -
Page 11: Installation
Standpipe height: minimum 500mm from the floor. CONNECT TO THE POWER SUPPLY... NOTE: Hotpoint recommend extension leads are not used. Move your machine into position, take care not to trap or kink the hoses. PLEASE USE THE NEW HOSES SUPPLIED, FITTED TO THE MACHINE. -
Page 12: The Dispenser Drawer
A cold fill adaptor is available from your local Connect fill hoses to Hotpoint authorised Service water supply taps: Centre or by calling the - Red or Grey Hose Genuine end to Hot Parts &...