Specifications; Display Resolutions - Insignia NS-32D511NA15 User Manual

Problem Solution
"No signal" error
• Press INPUT and make sure that you have selected the
message is
correct input for the device or service you are trying to
displayed
use.
• If you are using a cable or satellite box, use the remote
that came with that box to change channels.
After Auto Channel
• Reception can vary by channel depending on the
Search, there are
broadcast power level of a given station. Contact your
no channels
cable or satellite TV provider.
• Make sure that the antenna or cable/satellite TV is
connected securely to your TV.
• Try replacing the cable between the antenna/cable or
cable/satellite box and your TV.
One or more
• Make sure that the channels are not blocked. See "Setting
channels do not
parental control levels" in the online User Guide.
display
• Make sure that the channels are not hidden. The channel
may have been deleted from the channel list. You can
tune to the channel by pressing the number buttons or
you can add the channel back to the channel list. See
"Hiding channels" in the online User Guide.
• If you are using a cable or satellite box, use the remote
that came with that box to change channels.
• Make sure that you have the correct input selected to
view channels from the cable or satellite box.
• If you are using an antenna, the digital channel signal
may be low. To check the digital channel signal strength,
see "Checking the digital signal strength" in the online
User Guide.
Password is lost
• Enter 9999 to access parental controls, then set a new
password. See "Setting or changing the password" in the
online User Guide.
Some settings
• If a setting is grayed, the setting is not available in the
cannot be accessed
current video input mode. Press INPUT and make sure
that you have selected the correct input for the device you
are trying to use.
TV cabinet creaks
• When the TV is in use, the temperature rises naturally and
may cause the cabinet to expand or contract which can
cause a creaking noise. This is not a malfunction.
Control buttons do
• Make sure that the Button Lock option is set to Off. See
not work
"Locking control buttons" in the online User Guide.
• Unplug the power cord, wait a few seconds, then plug the
cord back in and turn on your TV.
TV keeps turning
• Make sure that the sleep timer is not turned on. See
off
"Setting the sleep timer" in the online User Guide.
Notes
• If the problem is not solved by using these
troubleshooting instructions, turn off your TV,
then turn it on again.
• Additional troubleshooting information is in
your online User Guide. Go to
www.insigniaproducts.com, then click
Support & Service. Enter your model number
in the box under Manual, Firmware, Drivers
& Product Information, then click

Specifications

Specifications are subject to change without notice.
Dimensions and weight
16.9 × 28.7 × 3.2 in. (42.9 × 72.9 × 8.14 cm)
Without stand
18.2 × 28.7 × 6.3 in. (46.2 × 72.9 × 16.0 cm)
With stand
.
10.2 lbs (4.63 kg)
10.6 lbs (4.8 kg)
www.insigniaproducts.com
Screen
Screen size measured
diagonally
Backlight type
Screen refresh rate
Display resolution
Panel resolution
Aspect ratio
Contrast ratio
(typical)–panel
Dynamic contrast ratio–
list value
TV Brightness (minimum)
cd/m2
Comb filter
Response time
Horizontal viewing angle
Vertical viewing angle

Display resolutions

HDMI suggested resolutions
Component video suggested
resolutions
Tuner
Analog
Digital
Inputs
HDMI
MHL-enabled and Roku Ready® (HDMI2/MHL jack)
Component video
Composite video
Shared audio (component
and composite)
PC/VGA
3.5mm DVI audio input
DVI (Shared with HDMI)
USB
Antenna/Cable
Outputs
Video
Analog audio/Headphone
Digital audio
WiFi
Ethernet
Audio
DTS Tuning Package
Speakers
NS-32D511NA15
31.5 in.
LED
60Hz
1080p
1920 (H) × 1080 (V)
16:9
3,000:1
500,000:1
160 nits
3d y/c digital
6.5 ms
160°
160°
1080p, 1080i, 720p, 480p, 480i
1080i, 720p, 480p, 480i
NTSC
ATSC, 8-VSB, Clear-QAM
1 (side)/1 (back)
E-EDID compliant/HDCP compliant
1 (back)
1 (back)
Shared with component Y
Yes
No
1 (back)
1
1 (back)
Supports JPEG and firmware upgrade
1 (side)
No
1 (side)
1 (optical) (side)
No
No
DTS Sound
Number: 2
Watts per channel: 5W
5