Page 1
1080P 1080P 47LE8500 47LE8500 47LE8500 47LE8500 Direct View LCD LED Backlights Training LCD-DV Troubleshooting 47" Class Full HD 1080P LCD TV (47" diagonally) Published July 23, 2010 Updated December 06 , 2010...
Page 2
Board Operation Troubleshooting of : • Switch Mode Power Supply • Inverter Boards Main and Secondary (LED Backlight Drivers) • Main Board • Extension Boards • Ft Control Board • Soft Touch Keys • Speakers July 2010 LCD TV 47LE8500...
Page 3
Overview of Topics to be Discussed Overview of Topics to be Discussed 47LE8500 LCD Direct View Display Section 1 This Section will cover Contact Information and remind the Technician of Important Safety Precautions for the Customers Safety as well as the Technician and the Equipment.
When servicing this product, under no circumstances should the original design be modified or altered without permission from LG Electronics. Unauthorized modifications will not only void the warranty, but may lead to property damage or user injury.
Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help. July 2010 LCD TV 47LE8500...
PDP Panel Alignment Handbook, the Learning Academy site the Learning Academy site Plasma Control Board ROM Update (Jig required) Published July 2010 by LG Technical Support and Training LG Electronics Alabama Inc LG Electronics Alabama, Inc. 201 James Record Road, Huntsville, AL, 35813.
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage and part number accuracy. 2. Check the model label. Verify model names and board model matches. 3. Check details of defective condition and history. Example: Oscillator failure dead set, etc… July 2010 LCD TV 47LE8500...
The final step is to correct the problem. Be careful of ESD and make sure to check the DC Supplies for proper levels. Make all necessary adjustments and lastly always perform a Safety AC Leakage Test before returning the product back to the Customer. July 2010 LCD TV 47LE8500...
Page 9
47LE8500 PRODUCT INFORMATION SECTION 47LE8500 PRODUCT INFORMATION SECTION This section of the manual will discuss the specifications of the 47LE8500 LCD Direct View Display July 2010 LCD TV 47LE8500...
Page 10
2. Wired Remote cable between the TV and Dongle for Control Functions. Media Box Wired Remote to control the Media Box TV A/V Inputs Wireless Receiver/Transmitter “Dongle” Attaches via Velcro to the back of the set HDMI July 2010 LCD TV 47LE8500...
Page 11
Wireless LAN (DLNA Adaptor) Wireless LAN (DLNA Adaptor) Wireless LAN (Sold Separately) Using the LG Wireless LAN for Broadband/ DLNA Adaptor, which is sold separately, allows the TV to connect to a wireless LAN network. The DLNA adaptor attaches to...
• 4 HDMI™ V.1.3 w/Deep Color • Seamless Design • SIMPLINK™ Connectivity • Picture Wizard II • Dolby® Digital 5.1 Decoder (Easy Picture Calibration) • Infinite Sound • Smart Energy Saving • ENERGY STAR® Qualified July 2010 LCD TV 47LE8500...
Page 13
47LE8500 Logo Familiarization Page 1 of 4 47LE8500 Logo Familiarization Page 1 of 4 New definition television. LG’s INFINIA TVs are redefining home entertainment. Even beyond their jaw-dropping design, they offer access to virtually unlimited entertainment through broadband connectivity and freedom with wireless HD capability.
Page 14
Enjoy twice the picture quality of standard HDTV with almost double the pixel resolution. See sharper details like never before. Just imagine a Blu-ray disc or video game seen on your new LG Full HD 1080p TV. HDMI (1.3 Deep Color) Digital multi-connectivity HDMI (1.3 Deep color) provides a wider bandwidth (340MHz,...
Page 15
47LE8500 Logo Familiarization Page 3 of 4 47LE8500 Logo Familiarization Page 3 of 4 AV Mode "One click" Cinema, Cinema, Sport, Game mode. TAKE IT TO THE EDGE is a true multimedia TV with an AV Mode which allows you to choose from 4 different modes of Cinema, Sports and Game by a single click of a remote control.
Page 16
TruMotion 240Hz See sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LG’s TruMotion 240Hz technology. Now your TV can keep up with the fastest moving scenes. July 2010 LCD TV...
Page 17
47LE8500 Remote Control 47LE8500 Remote Control BOTTOM PORTION p/n AKB72914003 TOP PORTION July 2010 LCD TV 47LE8500...
105-201M or p/n MKJ39170828 2) Press “In-Start” 3) A Password screen appears. 4) Enter the Password. Note: A Password is required to enter the Service Menu. Enter; 0000 Note: If 0000 does not work use 0413. MKJ39170828 105-201M July 2010 LCD TV 47LE8500...
Page 19
Rear In/Out Jacks Rear In/Out Jacks USB 2 USB 2 USB 1 USB 1 Component or Composite Video/Audio 3 Head Wireless Media Box Phones Remote Jack MAIN BOARD Rear and Side Input/Output locations HDMI 4 July 2010 LCD TV 47LE8500...
Simple Manual Bring up the Customer’s Menu then Press the Red button on Remote Scroll down to item 9 Network Connections With Software Update Highlighted, Press Select on Remote Continue on next page July 2010 LCD TV 47LE8500...
Page 21
SW version and serial No. is displayed. Note: Confirm the “Suffix” of the model number. If the Main board is replaced, the Model and Serial number must be reinserted into memory. See Model Number D/L. July 2010 LCD TV 47LE8500...
Page 22
Do not remove AC power or the USB Flash Drive. restarted. Do not turn off Power, during the upgrade 8) When download is completed, you will see process. “COMPLETE”. Software Files are now available from 9) Your TV will be restarted automatically. LGTechassist.com July 2010 LCD TV 47LE8500...
Manual “Forced” Download Menu. Any file can be downloaded when selected and may cause the Main board to become inoperative Example of files found if the incorrect file On the Jump Drive was selected. July 2010 LCD TV 47LE8500...
Use the cursor right or left to select the area to change. Use the cursor up or down to change. Cursor right until there is no text cursor blinking. Scroll down to highlight “Serial Number” and change. July 2010 LCD TV 47LE8500...
Service Menu: Downloading EDID Data Pg 1 of 2 Service Menu: Downloading EDID Data Pg 1 of 2 1) Press “ADJ” key. 2) Select menu, Either “PCM EDID D/L” or AC3 EDID D/L July 2010 LCD TV 47LE8500...
Page 26
Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G. This means that when PCM is OK, PCM audio is priority and when AC3 is OK, AC3 audio is priority. July 2010 LCD TV 47LE8500...
Page 27
47LE8500 Product Dimensions 47LE8500 Product Dimensions Wattage 1.3/8" There must be at least 4 inches of Clearance on all sides Local Dimming 90W 34.93mm Full White 130W 44.3/16" Stand By 0.1W 1122.68mm 8.7/16" 19.5/16" 214mm 490mm 7.7/8" 200mm Model No.
Disassembly: This section of the manual will discuss Disassembly, Layout (Circuit Board Identification) of the 47LE8500 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
Putting in an improper screw when reassembling may Cause damage. The AC Cord Stand Base is Glass Does Not unplug Handle with Care The Stand has to be removed before removing the back. July 2010 LCD TV 47LE8500...
Inverter Secondary Inverter Main Power Supply (SMPS) Main Board LVDS Cables Warning: The Frame has Panel Connection Points very sharp edges IR/LED Soft Touch LG Logo Invisible Invisible Speaker Right Speaker Left Board Keyboard Board July 2010 LCD TV 47LE8500...
Page 31
47LE8500 Connector Identification Diagram 47LE8500 Connector Identification Diagram If the Panel is replaced, reset the UTTTime. Service Menu, System 1 Item 12 TFT PANEL p/n: EAJ60874401 (Model AUSWLH) p/n: AFB72949901 (AUSWLUR / AUSWLNR) CN11 CN22 CN33 V25~V32 V73~V80 V105~V112 p/n: AFB72950101...
P201, P205, P204 and AC SK101 fits very In SK101. snug into it’s connector. Remove the 6 screws indicated by the arrows. Press in on the two tabs AC In to release lock SK101 July 2010 LCD TV 47LE8500...
Main board holding the Metal plate in place. NOTE: Always check on top and behind the Large P8800 P8200 ICs. And look for a piece of Chocolate (Heat Transfer Material). Be sure to transfer to new Board if present. July 2010 LCD TV 47LE8500...
Page 34
Use caution, do not allow screws to fall. CN11 NOTE: If Servicing the Board, leave the screws installed to provide stability and grounding. On CN2, CN3, CN4 and CN5 Flip the locking tab upward, pull the ribbons out. July 2010 LCD TV 47LE8500...
Page 35
Use caution, do not allow screws to fall. CN103 CN105 NOTE: If Servicing the Board, leave the screws installed to provide stability and grounding. On CN104 and CN105 Flip the locking tab upward, pull the ribbons out. July 2010 LCD TV 47LE8500...
Page 36
Removing Front IR Board p/n EBR64966401 Disconnect CON1, CON2 and CON3 connectors. Press upward on the two tabs at the top. Tilt the board downward and lift straight up. CON3 IR board / Intelligent Sensor CON1 July 2010 LCD TV 47LE8500...
TROUBLESHOOTING SECTION TROUBLESHOOTING SECTION Troubleshooting: This section of the manual will discuss troubleshooting. Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems. July 2010 LCD TV 47LE8500...
24V is routed out P201 pins 2, 3 and 4. P204 Connector: (To Inverter Main Board) 24V is routed out P204 pins 1 through 5. P205 Connector: (To Inverter Secondary Board) 24V is routed out P205 pins 1 through 5. July 2010 LCD TV 47LE8500...
Page 39
Power Supply (SMPS) Board Layout Power Supply (SMPS) Board Layout p/n EAY60908801 F101 3.15A/250V STBY 2.9V Run 393.3V From Hot Gnd F501 3.15A/250V STBY 159.6V Run 392.6V From Hot Gnd F100 6.3A/250V AC Protect Hot Ground Shock Hazard July 2010 LCD TV 47LE8500...
Page 40
47LE8500 Power Supply Start Up Sequence 47LE8500 Power Supply Start Up Sequence CN101 CN104 POWER SUPPLY (SMPS) AC In P205 Inverter Primary side fuse: Stand-By 159.6V Secondary Run 392.6V (Hot Gnd) CN104 CN103 CN25~CN33 24V B+ for the Inverters No AC Det in...
Page 41
47LE8500 Television Turn On Commands Circuit Drawing 47LE8500 Television Turn On Commands Circuit Drawing R8003 22KΩ +12V Q8004 R8010 10KΩ L8000 To IC9103 DC to R8001 Panel_Vcc (12V) Q8003 Q8001 DC Conv T-CON R8011 1.8K 11.79V 11.8V 1.8V 0.68V R8103...
Page 42
Check that the 24V and 12V power supplies are turned on, • P201 (12V pins 17, 19 and 21) • P201 (24V pins 2, 3 and 4) • P204 and P205 (24V pins 1 through 5) to the Inverters (2) Remove AC power July 2010 LCD TV 47LE8500...
Page 43
Check the connections to the Inverters. If the 24V and the Inverter On command is arriving at the Inverters in, then see Inverter Section for further testing. Note: Either Inverter can run separately. REMOVE AC POWER: July 2010 LCD TV 47LE8500...
OSD Backlight setting and then Intelligent Sensor 11.9V 1.39V (room light condition) Output from the Video Processor Open IC900. Range 0.37V to 3.3V. Open ERROR Open Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 45
(1) PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V. I-C is the Inverter On Control Signal Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 46
Pins 1 and 2 for STBY and RUN. F100 Bottom Right of SMPS F100 (Diode Check) Main Power Switch Closed F100 Red or Black Lead on Fuse (Open) Other Lead on Hot Ground 6.3A/250V AC IN SK101 July 2010 LCD TV 47LE8500...
Page 47
STBY 159.6V Run 392.6V From Hot Gnd STBY 2.9V Run 393.3V If reading the voltage on F101 right after power off, it takes a very long time to bleed down to the reading given here. July 2010 LCD TV 47LE8500...
Each Extension board has 9 connections to the Backlight LEDs. There are 4 LEDs per/block, 216 Blocks, 8 Blocks per/cartridge, 3 Cartridges per/bar, 9 bars (rows), 32 LEDs per/cartridge, 96 LEDs per/bar. With a total of 864 LEDs. July 2010 LCD TV 47LE8500...
Page 49
IOP Structure Integrated Optic Plate IOP Structure Integrated Optic Plate The Image below shows the actual Backlight Bars used in the 47LE8500. The Cartridges are assembled from the bottom to the top, like shingles on a roof. Cartridge Cartridges Removed...
Page 50
IOP Structure Information 4 LEDs per/block (216 Blocks) 8 Blocks per/cartridge, 9 bars with 3 cartridges per/bar, 32 LEDs per/cartridge, 96 LEDs per/bar. 864 LEDs total. Cartridge BLU (Backlight Unit) Cartridge There are 3 Cartridges per/bar. July 2010 LCD TV 47LE8500...
Page 51
47LE8500 (IOP) Cartridge Breakdown 47LE8500 (IOP) Cartridge Breakdown Each Connector has 10 pins. 2 are B+ 13V and 8 block controls. Connector Slots Back Metal Plate The Individual LEDs Front Metal Plate can be checked using the Diode Mode forward bias test. The LED Bar 32 LEDs 4 LEDs per/block 8 blocks LED will light.
Page 56
47LE8500 Inverter (Main) B+ Routing 47LE8500 Inverter (Main) B+ Routing To CN 1 Extension Left To CN 2 Extension Left CN3 B+ for LED Blocks. CN2 B+ for LED Blocks. Pins 1~2, 11~12, 21~22, Pins 9~10, 11~12, 31~32, 41~42. 21~22, 31~32 24.6V...
Page 57
47LE8500 Inverter (Secondary) B+ Routing 47LE8500 Inverter (Secondary) B+ Routing U103 3.3V DO NOT MEASURE L207 Q108 Q109 3.4V 24.6V To CN 23 F101 Extension Right 12A/65V DC to DC INVERTER (SECONDARY) CN104 B+ to LED Blocks pins Driver 24.6V...
Page 58
Q4, Q7 or Q105 Pin 3 30V p/p 296KHz 13.5V p/p 296KHz 30V p/p 296KHz Each of the Pin numbers for the Components listed Q5, Q8 or Q106 Pin 3 is Ground above are the same. July 2010 LCD TV 47LE8500...
Page 59
I2C data back to the Main board’s Microprocessor. Minimum P-DIM Voltage 0.37V 0% Cust Backlight Setting Backlights Dim Brightness and Contrast adjustments do not affect P-DIM Analog Dimming is not used. It is a fixed voltage. Also called BR1, VBR-A, BCM-VBR-A, ADM July 2010 47LE8500 LCD-DV...
Page 60
0.58V (Black Lead on Fuse) 12A/65V Top Left of the Board Inverter (Secondary) Just to the right of CN101 Connector F101 (Diode Mode Check) 1.385V (Red Lead on Fuse) 0.58V (Black Lead on Fuse) F101 12A/65V July 2010 LCD TV 47LE8500...
Page 61
Inverter Crystals Y1, Y501 (Main) and Y501 on (Secondary) Inform ation Inverter Crystals Y1, Y501 (Main) and Y501 on (Secondary) Inform ation Crystal Y301 Y501 Use Top Leg Inverter (Main) 8Mhz Inverter (Secondary) Y501 Use Bottom Leg July 2010 LCD TV 47LE8500...
Page 62
CN2 13V Line Pins CN3 13V Line Pins CN4 13V Line Pins CN5 13V Line Pins 1~2, 11~12, 9~10, 11~12, 1~2, 11~12, 21~22, 11~12, 21~22, 31~32, 9~10, 19~20, 29~30, 21~22,31~32, 41~42 21~22, 31~32 31~32, 41~42 41~42 39~40, 49~50 July 2010 LCD TV 47LE8500...
Page 63
Turn off the set and unplug the connector to the Inverters coming from the Main board. If the brightness returns to normal, the Main board is defective. If not, investigate all inverter voltages, if OK, use the grounding of each V block procedure to test the panel’s backlight LEDs. July 2010 LCD TV 47LE8500...
Page 64
CN4 pin 08 0.7V~3.9V white and black CN4 pin 07 0.7V~3.9V screens CN4 pin 06 0.7V~3.9V CN4 pin 05 0.7V~3.9V CN4 pin 04 0.7V~3.9V CN4 pin 03 0.7V~3.9V CN4 pin 02 12.55V CN4 pin 01 12.55V July 2010 LCD TV 47LE8500...
Page 65
Processor IC900. Range 0.37V to 3.3V. CN101 "Inverter Secondary" Connector To P205 "SMPS" Diode Label STBY Check 24.6V 0.42V 6~10 P-DIM 0.37V~3.3V Open 2.92V Open Inverter On Control Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 66
Open M2_SCLK 0.23V Open M1_MOSI *0.04V~3.26V Open M1_SCLK 0.23V Open Open Open S_CS_N 2.6V 1.65V S_MOSI *0.18V~0.28V 1.61V *Black to White S_SCLK 2.99V 1.62V *Black to White Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 67
Inverter Main and Secondary Local Dimming Control Signals Wavefo Inverter Main and Secondary Local Dimming Control Signals Wavefo For clearer details see the Interconnect Diagram July 2010 LCD TV 47LE8500...
See next page for VIDEO component PROCESSOR identification IC900, T-CON IC9001 and Tru-Motion IC9301 runs Hot. P9000 This is normal. P8100 Component These connectors are Mini plug type Wireless Remote P8800 To Speakers P8200 To Front IR July 2010 LCD TV 47LE8500...
Page 74
X9001 X9000 IC9001 T-CON Crystal Dimming Crystal 1.58V 2.54V p/p 1.56V 3.19V p/p Runs when set is On 4.86V p/p 1.6V 1.6V 3.27V p/p 25Mhz 12Mhz Runs when set is On X9001 X9000 MAIN Board July 2010 LCD TV 47LE8500...
Page 75
Either leg 2.26V p/p 1.52 1.3V 789mV p/p Either leg 10Mhz 54Mhz Runs all Runs when set is On The time MAIN Board 1.85V p/p 2.82V p/p X8100 X8101 X1001 1.5V 1.75V Runs all The time July 2010 LCD TV 47LE8500...
Page 76
Main Board DC to DC Converter (Voltages for Panel) Checks Location: Top Center of Board +7.81V L9100 HVDD IC9102 Panel 12V L9104 +16V B+ for IC9102 IC9103 L9102 D9101 Panel 12V +27V IC9103 L9101 +3.3V D9102 July 2010 LCD TV 47LE8500...
Page 77
Main Board Additional Panel Voltage Checks Location: Top Left of Board P7501 P7500 IC9101 Back Side of Board From IC9101 Pin 21 -4.8V (VDD-ODD) From IC9101 Pin 19 -4.7V (VST) From IC9101 Pin 20 -4.8V (VDD-EVEN) July 2010 LCD TV 47LE8500...
Page 78
Open Open ERROR PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Diode Mode values taken with all Connectors Removed Range 0.37V to 3.3V. July 2010 LCD TV 47LE8500...
Page 79
1.09V CLK5 1.5V OPT_N 1.06V 2.06V CLK4 1.5V H_CONV 1.07V 3.3V 1.64V CLK3 1.5V VST_IN 1.06V 3.3V 1.64V CLK2 1.5V 0.62V 1.06V CLK1 1.5V 0.3V 1.06V HVDD 7.81V Open Z_OUT 7.7V Open HVDD 7.81V Open July 2010 LCD TV 47LE8500...
Page 80
Open RV3- 1.27V 0.9V GMA6 11.88V Open VCOM_IN 6.86V Open RV4+ 1.12V 1.09V GMA4 12.79V Open RV4- 1.22V 0.9V GMA3 13.5V Open 15.57V Open RV5+ 1.13V 1.09V GMA1 14.91V Open 15.57V Open RV5- 1.22V 0.9V July 2010 LCD TV 47LE8500...
Page 81
1.24V LED_LOGO Open 1.57V 1.54V Open +3.3V_Normal 3.3V 0.59V LED_R/BUZZ Open Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p) IR pulses (1.6V p/p) Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 82
0.23V 1.1V M1_MOSI *0.04V~3.26V 1.08V M1_SCLK 0.23V 1.08V M3_MOSI 1.1V M3_SCLK 1.1V S_CS_N 2.6V 1.08V S_MOSI *0.18V~0.28V 1.08V *Black to White S_SCLK 2.99V 1.08V *Black to White Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 83
Pin 25 P8800 CONNECTOR "Main" to "Speakers" LABEL Diode Check IC8801 SPK-R(-) 12.3V Open SPK-R(+) 12.3V Open Audio B+ SPK-L(-) 12.3V Open Pins 49-52 SPK-L(+) 12.3V Open P8800 Diode Mode values taken with all Connectors Removed July 2010 LCD TV 47LE8500...
Page 84
Remove cover, (see Wireless Media Box training manual for details). *24V Switched from Q8701 Drain Back side of the board. Q8701 turned on by Q8700 front side of the board. Q8700 turned on by Microprocessor pin 38. July 2010 LCD TV 47LE8500...
IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also connects with the Soft Touch Key Board and the Center LG Logo board. The Center LG Logo lights after power on and the picture appears. Then dims down in about 2 seconds. At power off, it does the reverse.
Page 86
Front IR Board (Connections Identified) Front IR Board (Connections Identified) p/n EBR64966401 To Soft Touch CON3 CON2 Key Board To Center Logo Board CON1 P100 To Main Board IR board and Intelligent Sensor board July 2010 LCD TV 47LE8500...
Page 87
3.45V 3.36V Open LED_LOGO Open 3.45V 3.36V Open 1.57V 1.54V Open CON3 "Front IR" to “LG Logo Board" +3.3V_Normal 3.3V Open STBY Diode Check LED_R/BUZZ Open 3.45V Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p) 1.36V 0.6V...
Page 88
INVISIBLE SPEAKER SECTION INVISIBLE SPEAKER SECTION Speaker p/n EAB60961501 The 47LE8500 contains the Invisible Speaker system. The Full Range Speakers point downward, so there is no front viewable speaker grill or air ports. Installed Top View Side View Front View...
This Power Point shows a graphical representation of the 11 X 17 This Power Point shows a graphical representation of the 11 X 17 foldout page so clarity is limited. foldout page so clarity is limited. July 2010 LCD TV 47LE8500...
Page 90
47LE8500 INTERCONNECT DIAGRAM Note: If a particular block is exhibiting a dimmer level Each connector (27 total) to the LED Blocks (216) Drive Signals INVERTER (SECONDARY) V73~V80 P204 "SMPS" To CN1 "INVERTER Main" P205 "SMPS" To CN201 "INVERTER Secondary" V25~V32...
Page 91
42LE8500 Inverter Main and Secondary Local Dimming Control Signals Waveforms 42LE8500 Inverter Main and Secondary Local Dimming Control Signals Waveforms CN11 INVERTER (MAIN) FROM P7900 MAIN BOARD Inverter Main CN11 pin 01 Inverter Main CN11 pin 02 Inverter Main CN11 pin 02 Inverter Main CN11 pin 03 Inverter Main CN11 pin 03 Black or White Screen...
Page 92
47LE8500 MAIN (FRONT SIDE) SIMICONDUCTORS IC700 (+1.26V_TU) IC8002 (D1.8V) IC8005 (+3.3V_NORMAL) IC8902 (+1.26V_MEMC) IC9102 DC to DC Q8003 PANEL_VCC Q8800 AMP_MUTE Regulator Regulator Regulator Regulator HVDD T-CON Pin 25 IC8801 Control 2nd Driver [1] 0V (Gnd) [1] 5V [1] 0V (Gnd)
Page 93
47LE8500 47LE8500 Conclusion Conclusion Direct View LCD Direct View LCD Page Page This concludes the 47LE8500 training session.