Hoshizaki DM-200B Service Manual
Ice and water dispenser
Hide thumbs
Also See for DM-200B:
- Parts list (18 pages) ,
- Instruction manual (13 pages) ,
- Dimensions (2 pages)
Related Manuals for Hoshizaki DM-200B
Summary of Contents for Hoshizaki DM-200B
- Page 1 Hoshizaki America, Inc. “A Superior Degree of Reliability” www.hoshizaki.com Ice and Water Dispenser Model DM-200B SERVICE MANUAL Number: 73142 Issued: 8-24-2006...
- Page 2 HOSHIZAKI provides this manual primarily to assist qualified service technicians in the service and maintenance of this product. Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write or send an e-mail message to the HOSHIZAKI Technical Support Department. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
Please review this manual. It should be read carefully before this product is serviced or maintenance operations are performed. Only qualified service technicians should service and maintain this product. This manual should be made available to the technician prior to service or maintenance. -
Page 4: Specifications
I. Specifications A. DM-200B AC SUPPLY VOLTAGE AMPERAGE MINIMUM CIRCUIT AMPACITY MAXIMUM FUSE SIZE APPROXIMATE ELECTRIC CONSUMPTION 110 W APPROXIMATE STORAGE CAPACITY APPROXIMATE ICE DISPENSING SPEED EXTERIOR DIMENSIONS ( W x D x H ) INTERIOR DIMENSIONS ( W x D x H ) -
Page 5: General Information
II. General Information A. Construction 1. DM-200B Manual Fill Cover Agitator Capacitor Water Dispense Switch Ice Dispense Switch Side Panel Spout Front Panel Apron Panel Water Valve Drain Grill Gear Motor Assembly Solenoid Assembly... -
Page 6: Technical Information
III. Technical Information A. Wiring Diagram 1. DM-200B... -
Page 7: Service Diagnosis
IV. Service Diagnosis Problem Possible Cause [1] No ice dispensed. a) Power Supply b) Dispense Switch c) Gear Motor d) Solenoid e) Mechanism f) Ice Storage [2] No water dispensed. a) Power Supply Remedy 1. Off at breaker or cord 1. - Page 8 Problem Possible Cause b) Water Supply c) Dispense Switch [3] Abnormal noise. a) Gear Motor or Gear Head b) Mechanism c) Solenoid [4] Ice supply in storage a) Bin Drain bin often melts. Remedy 3. Bad contacts. 3. Check for continuity and replace.
-
Page 9: Removal And Replacement Of Components
V. Removal and Replacement of Components Ensure all components, fasteners and thumbscrews are securely in place after the equipment is serviced. A. Removal and Replacement of Gear Motor 1) Unplug the unit from the electrical outlet. 2) Remove the panels. 3) Disconnect the gear motor wiring harness. -
Page 10: Removal And Replacement Of Solenoid
B. Removal and Replacement of Solenoid 1) Unplug the unit from the electrical outlet. 2) Remove the panels. 3) Disconnect the connectors from the solenoid leads. 4) Remove the solenoid, and install a new solenoid. 5) Connect the connectors to the solenoid leads. 6) Replace the panels in their correct positions. -
Page 11: Cleaning And Maintenance Instructions
7) Dilute 5 fl. oz. (148 ml) of Hoshizaki "Scale Away" with 1 gallon (3.8 l) of warm water. 8) Scrub the cover, spout, apron panel, shutter assembly, agitator, and the inside of the bin using a nylon scouring pad, brushes and cleaning solution. - Page 12 Front Panel Snap Screw Shutter Assembly Spout Apron Panel Cover Thumbscrew Fig. 1 Agitator...
-
Page 13: Maintenance - Exterior Panels
B. Maintenance – Exterior Panels To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. C. Preparing the Dispenser for Long Storage When shutting off the dispenser for an extended time, drain out all water from the water line and remove the ice from the dispensing bin.