Hoshizaki DM-200B Instruction Manual
Ice and water dispenser
Hide thumbs
Also See for DM-200B:
- Parts list (18 pages) ,
- Service manual (13 pages) ,
- Dimensions (2 pages)
Related Manuals for Hoshizaki DM-200B
Summary of Contents for Hoshizaki DM-200B
- Page 1 Hoshizaki Hoshizaki America, Inc. Ice and Water Dispenser Model DM-200B INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com Issued: 8-8-2006...
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write or send an e-mail message to the HOSHIZAKI Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
• Keep this manual with this product for later reference. I. Specifications... 4 A. Nameplate Rating ... 4 1. DM-200B ... 4 B. Dimensions/Connections ... 5 1. DM-200B ... 5 II. Installation and Operating Instructions ... 6 A. -
Page 4: Specifications
I. Specifications A. Nameplate Rating 1. DM-200B HOSHIZAKI ICE DISPENSER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AMPERES See the nameplate for electrical specifications. This nameplate is located on the upper right hand side of the rear panel. Since this nameplate is located on the rear panel of the dispenser, it cannot be read when the back of the dispenser is against a wall or against another piece of kitchen equipment. -
Page 5: Dimensions/Connections
B. Dimensions/Connections 1. DM-200B Unit: mm [inches]... -
Page 6: Installation And Operating Instructions
II. Installation and Operating Instructions A. Checks Before Installation 1. Remove the shipping carton and all tape and packing material to prevent possible damage to the unit. 2. Ensure all components, fasteners and thumbscrews are securely in place. • Remove the package containing the accessories. •... -
Page 7: Setup
C. Setup It is extremely important that the dispenser be leveled in both the left-to-right and front-to-rear directions. If it is not level, a reduced rate of ice flow may result. 1) Unpack the dispenser, and remove the shipping carton and all tape and packing material before operating the unit. -
Page 8: Water Supply And Drain Connections
E. Water Supply and Drain Connections See Fig. 1 • Water supply inlet is 1/2" female pipe thread (FPT). • A water supply line shut-off valve and drain valve should be installed. A minimum of 1/4" OD copper tubing is recommended for the water supply line. •... -
Page 9: Final Checklist
12) Has the warranty card been filled out and forwarded to the factory for warranty registration? G. Startup 1) Remove the top and use a clean, sanitary container for filling the ice dispenser with ice. Reinstall the top. 2) Open the water supply line shut-off valve. -
Page 10: Cleaning And Maintenance Instructions
6) Remove the snap pin securing the shutter assembly. Slide the shutter shaft to the left, pull out the right side and slide out. 7) Dilute 5 fl. oz. (148 ml) of recommended cleaner Hoshizaki "Scale Away" or "LIME-A- WAY," (Economics Laboratory, Inc.) with 1 gallon (3.8 l) of warm water. - Page 11 Front Panel Snap Screw Shutter Assembly Spout Apron Panel Thumbscrew Cover Fig. 2 Agitator...
-
Page 12: Maintenance - Exterior Panels
B. Maintenance – Exterior Panels To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. C. Preparing the Dispenser for Long Storage When shutting off the dispenser for an extended time, drain out all water from the water line and remove the ice from the dispensing bin. - Page 13 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A5DA10A...