Subscribe to Our Youtube Channel
Related Manuals for JamHub Tracker MT16
Summary of Contents for JamHub Tracker MT16
- Page 1 © 2014 JamHub Corp. All Rights Reserved. P.O. Box 482 Whitinsville, MA | www.JamHub.com...
-
Page 2: Table Of Contents
Connecting Your Tracker MT16 to a JamHub Studio Using the Tracker MT16 Breakout Cable SAVE THE MUSIC Insert Your SD Card Formatting Your SD Card © 2014 JamHub Corp. All rights reserved. Product features, specifications, system requirements, and availability are subject to change without notice. Patents Pending. - Page 3 How to Set Up Your Wireless Network - WiFi What is BandLab™? How to Link to Your BandLab™ Account BandLab™ Cloud Ethernet 10/100 Megabits Per Second (Mbps) Status STORAGE To Reformat Your SD Card To Update Your Tracker MT16 To Restore Factory Defaults Troubleshooting Warranty...
-
Page 4: Welcome
INTRODUCTION This guide is intended to get you up and recording with your new JamHub Tracker MT16. To get the most out of your experience, please read the full manual thoroughly. If this copy is lost, a copy of the manual can always be downloaded at www.JamHub. -
Page 5: Fcc Warning
» Consult the dealer or an experienced radio/TV technician for help. Declaration of Conformity JamHub hereby declares that this Tracker MT16™ Multitrack Recorder is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. -
Page 6: What's In The Box
V DC adapter JamHub Connect Cable Port – to plug your Tracker MT16 directly into your JamHub studio © 2014 JamHub Corp. All rights reserved. Product features, specifications, system requirements, and availability are subject to change without notice. Patents Pending. -
Page 7: Lights
Note: Any single channel will set the clip light off letting you know that a channel is clipping (distorting the sound) before it gets to the Tracker MT16 inputs. Lower the level at the source until the clip light no longer flashes. Buttons 15. -
Page 8: Power
Plug your Tracker MT16 into the wall using the provided 5V DC Adapter. When your Tracker MT16 is powered on, the PWR light will turn blue and the LCD will display, Initializing, please wait… Your Tracker MT16 is a fully functioning UNIX computer, so it will take a moment to boot up. -
Page 9: Why A Half Insert
Why a Half Insert? Insert Jack signals have 3 components: a Send, a Return, and a Ground. If you fully insert a mono cable, the lack of a Return will cause the signal to ground out. By using the Half Insert technique, you will ensure that only the Send continues through the mixer and you will not shut off the channel strip. -
Page 10: Connecting Your Tracker Mt16 To A Jamhub Studio
Your Tracker MT16 comes with a JamHub Connect cable to connect to any JamHub studio. Simply plug the JamHub Connect cable into the JamHub Connect port on the back of your Tracker MT16, and plug the other side into any of the SoleMix™ remote ports on the back of your JamHub studio. -
Page 11: Using The Tracker Mt16 Breakout Cable
Formatting Your SD Card To format a new SD Card for your Tracker MT16, go to SETTINGS, then scroll through the menu to the Format SD option and press . Be aware that reformatting an SD Card will wipe any preexisting data off that card and you will lose any files previously stored on the SD Card. -
Page 12: Recording
16-channels can be saved as a COMBINED WAV which will appear as one saved file. Recording in COMBINED mode reduces the amount of time your Tracker MT16 will need to encode, streamlining your recording experience. To break COMBINED files out into their component WAV files, run the Breakout Utility on your computer (found on your SD card and available to download at JamHub.com) or upload your files to BandLab. -
Page 13: Sample Rate - 44.1Khz, 48Khz, 96Khz
1-6 may be activated during 96KHz recording when using an SD card. Recording using the JamHub mapping will also be disabled in this mode. To record all 16 channels of audio in 96KHz, make sure that your Tracker MT16 is running software revision #2.0 or higher. -
Page 14: Record On/Off
’ indicates the current setting While your Tracker MT16 is armed for recording, the CLIP light will be active, flashing red when incoming signal is too hot and needs to be turned down. Check your sound and levels with your recorder armed. -
Page 15: Recording
SD card to record on. Note: Your Tracker MT16 will monitor the space left on your SD card and take the precaution of properly ending your recording when levels drop below a certain threshold to allow for proper encoding. -
Page 16: Reviewing Your Recordings
REVIEWING YOUR RECORDINGS How to Listen to a Recording In your Tracker MT16’s top level menu, you will find PLAY. By entering the PLAY menu you will be able to scroll through any recordings you have made in SPLIT mode and listen to them using the headphone out on your Tracker MT16. -
Page 17: What Is Bandlab
Go to the Tracker MT-16’s Settings menu and find BandLab Cloud » in the Connection Status menu switch between online and offline modes. When your Tracker MT16 is online, you will be able to upload files wirelessly to BandLab. »... -
Page 18: Ethernet 10/100 Megabits Per Second (Mbps)
Tracker MT16™ — User Guide Ethernet 10/100 Megabits Per Second (Mbps) The Tracker MT16 has a built in high speed Ethernet port to connect to wired network(s) up to 100Mbps. The advantage of a wired network is higher upload and download receive and transfer rates to the Internet. -
Page 19: Storage
To Reformat Your SD Card In the event that you need to format, or reformat, an SD card in order to make it compatible with your Tracker MT16, you will find the options you need in the Settings menu. Settings → Format SD Card → Yes »... -
Page 20: Warranty
Buyer or unauthorized parties. Out-of-warranty repairs will be invoiced at the current JamHub hourly rate plus the cost of parts, shipping and handling. JamHub reserves the right to elect, at its discretion, to give Buyer a refund of Buyer’s purchase price instead of a repair or replacement.
Need help?
Do you have a question about the Tracker MT16 and is the answer not in the manual?
Questions and answers