Specifications - Philips FW-C798/21/37 Service Manual

SPECIFICATIONS

GENERAL:
Mains voltage : 110-127V/220-240V Switchable for /21/21M
120V for /37
220V for /33
220-230V for /22/34
230-240V for /30
Mains frequency : 50/60Hz
Power consumption : < 1W at ECO Power Standby
: 25W at Standby (DEMO mode off)
: 175W at Active
Clock accuracy : < 4 seconds per day
Dimension centre unit : 265 x 310 x 390mm
TUNER:
FM
Tuning range
Grid
IF frequency
Aerial input
Sensitivity at 26dB S/N
Selectivity at 600kHz bandwidth
Image rejection
Distortion at RF=1mV, dev. 75kHz
-3dB Limiting point
Crosstalk at RF=1mV, dev. 40kHz
MW
Tuning range
Grid
IF frequency
Aerial input
Sensitivity at 26dB S/N
Selectivity at 18kHz bandwidth
IF rejection
Image rejection
Distortion at RF=50mV, m=80%
LW
Tuning range
Grid
IF frequency
Aerial input
Sensitivity at 26dB S/N
Selectivity at 18kHz bandwidth
IF rejection
Image rejection
Distortion at RF=50mV, m=80%
: 87.5-108MHz
65.81-74MHz for /34
1)
: 50kHz (& 30kHz for /34)
100kHz for /37
: 10.7MHz ± 25kHz
: 75Ω coaxial
300Ω click fit for /37
: < 7µV
: > 25dB
: > 25dB
: < 3%
: < 8µV
: > 18dB
: 531-1602kHz
530-1700kHz for /21/21M/37
: 9kHz
10kHz for /21/21M/37
: 450kHz ± 1kHz
: Frame aerial
: < 4.0mV/M
: > 18dB
: > 45dB
: > 28dB
: < 5%
: 153-279kHz /22
: 3kHz
: 450kHz ± 1kHz
: Frame aerial
: [< 6.0mV/M]
: [> 24dB]
: [> 45dB]
: [> 30dB]
: [< 5%]
1-3
AMPLIFIER:
Output power (6Ω, 1kHz, 10% THD)
L & R : 2 x 140W RMS
Output power (6Ω, 60Hz-12.5kHz, 10% THD)
L & R : 2 x 110W FTC
Frequency response within -3dB
Incredible Surround
WOOX
Digital Sound Control (DSC)
Virtual Ambience Control (VAC) : Hall, Concert, Cinema,
Input sensitivity
Output sensitivity
Line out (Left/Right) : 450mV ± 2dB at 22kΩ
Digital out : IEC 958, 44.1kHz
Booster out (Classic Mode) : 900mV at 22kΩ (Vol. Max.)
Headphone output at 32Ω : 700mV ± 1dB (Vol. Max.)
CASSETTE RECORDER:
Number of track
Tape speed
Wow and flutter
Fast-wind/Rewind time C60
Bias system
Rec/Pb frequency response within 8dB : 80Hz - 10kHz
Signal to Noise Ratio (Type I)
COMPACT DISC:
Measurement done at output conn. of the CDC module.
Frequency response
Output Voltage (in Vrms)
Signal to Noise Ratio (A-weighted) : > 80dBA
Distortion at 1kHz
Channel Unbalance
Channel Separation (1kHz)
De-emphasis : 0 or 15/50 mS (Switched by subcode
on the disc)
[....] Values indicated are for "ECO6 Cenelec Board" only.
Default setting is OFF, to switch on please refer page 3-4.
1)
/21
/37
: 50Hz-20kHz
: ON/OFF
: Level 1, 2, 3 & OFF
: Digital, Rock, Pop,
Newage, Classic, Electric
Disco, Arcade, Cyber
Aux in : 500mV ± 3dB at 1kHz
CDR in : 1V ± 3dB at 1kHz
: 2 x 2 stereo
: 4.76 cm/sec ± 2%
: < 0.4% DIN
: 130 sec
: 78kHz ± 10kHz
: > 48dBA
: < ±1.5dB for 20Hz-20kHz
: 500mV ± 2dB unloaded
: < 0.02%
: < ±1dB
: >60dB