Page 1
**Refer to page 2 if you want to know system configuration. * Refer to parts list on page 33. KENWOOD-Crop. certifies this equipment conforms to DHHS In compliance with Federal Regulations, following are repro- Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J.
RXD-655/755 EXTERNAL VIEW Cabinet(TOP) (A02-3014-08) ANTENNA FM Antenna (E70-0145-08) Pin jack(AM) AM LOOP (E40-8933-08) VIDEO Pin jack /AUX (E63-1219-08) SPEAKERS Lock terminal board (E70-0144-08) AC power cord bushing (J42-0338-08) AC power cord * (E30-) * Refer to parts list on page 33 .
RXD-655/755 DISASSEMBLY FOR REPAIR Caution on Disassembly Follow the below-mentioned notes when disassembling (A1)x2 Top Cabinet the unit and reassembling it, to keep it safe and ensure ø3x12mm excellent performance: 1. Take cassette tape and compact disc out of the unit.
Page 5
RXD-655/755 DISASSEMBLY FOR REPAIR (L2) x1 CLAMP LEVER Turntable CAM GEAR RIB Disc Tray (L1) x2 Figure 8-1 (F1)x1 (F1)x1 ø3x6mm ø3x10mm CD Player Unit Figure 8-4 (E2)x2 (E3)x1 (M1) x3 (E4)x1 Power Supply Main PWB (E2)x1 (M1) x3 (F2)x1...
Page 6
RXD-655/755 DISASSEMBLY FOR REPAIR (P2) x3 Mechanism Loading Motor (P1) x1 (P1) x1 TAPE2 Record/Playback Head (Q1) x5 Erase Head Figure 9-1 (A1)x2 Ø2x9mm Figure 10-1 REMOVING AND REINSTALLING TAPE1 THE MAIN PARTS Playback Head TAPE MECHANISM SECTION Perform steps 1 to 7 and 9 of the disassembly method to remove the tape mechanism.
Page 7
RXD-655/755 DISASSEMBLY FOR REPAIR How to remove the belt (TAPE 2) (See Fig. 10-4) 1. Remove the main belt (E1) x 1 pc., from the motor side. 2. Remove the FF/REW belt (E2) x 1 pc. Motor How to remove the motor (See Fig. 10-5) 1.
Page 8
FM IF SO301A FE301 CF301 CF303 ANTENNA FL701 FM IF TERMINAL Q301 FM IF DISPLAY QT21 FM FRONT END to CD X351 CF351 SECTION 456kHz FM IF T351 L351 AM IF L.P.F Q706- DRIVER IC700(1/2) Q907 AM LOOP ANT IC303 RX701 M901 FAN MOTOR...
Page 9
33.8688MHz CONSTANT RFVDD VOLTAGE CNP7 VVDD R-CH +3.3V AGND PICK UP UNIT ADAVDD LCHO L-CH MAIN DGND SECTION LVSS XVDD RVSS LVDD RCHO RVDD FIN1 CONT4 CNP8 FIN2 LC78645E SERVO/SIGNAL TIN1 CONTROL CONT3 TIN2 CONT2 5 DI DISPLAY SECTION CD RES CLAMP SW OC.
RXD-655/755 CIRCUIT DESCRIPTION 1. Port Description of Microprocessor Port No. Port Name Function POWER SUPPLY(+5V) -20dB ATT -20dB ATTENUATION NO USE/DSA STB T BIAS DECK BIAS CONTROL T T1/T2 DECK T1/T2 CHANGE OVER REC/PLAY DECK RECORDING/PLAYBACK CHANGE OVER RES OUT...
RXD-655/755 CIRCUIT DESCRIPTION Port No. Port Name Function DECK REVERSE RECORDING SWITCH INPUT MIC IN OPEN MP3 LED OPEN DESTOUT DISCRIMINATION PORT FOR DESTINATION STANDBY LED STANDBY LED CONTROL KARAOKE LATCH OPEN NO USE/MPEG POW CONNECTED TO GROUND RDS RST...
Page 12
RXD-655/755 CIRCUIT DESCRIPTION 2-2 RDS Demodulation LSI(TUNER Section, ICT21) Port No. Port Name Function VREF Reference voltage output. MPXIN Baseband (multiplexed) signal input. VDDA Analog power supply (+5V). VSSA Analog ground. FLOUT Subcarrier output (filter output). Subcarrier input (comparator input).
RXD-655/755 CIRCUIT DESCRIPTON 3-3 Contents of the Test Mode Enter the Test Mode 3-3-1 CD Test Mode OPEN/CLOSE operation is using manual << $ ! >>, << ⁄ › >> buttons make pick's slide possible. << PLAY >> key input <<...
Page 14
RXD-655/755 CIRCUIT DESCRIPTON 3-3-3 Initializing the CD changer Function: The SET will be set to "shipping - All the function, condition are initialized. - CLEAR ALL TUNER PRESET MEMORY . - CLOCK INITIAL - CLEAR CD MEMORY - Initialize the CD changer mecha and compact cassette mecha.
Page 15
RXD-655/755 CIRCUIT DESCRIPTON 3-3-4 CD Changer Aging Test Mode START " " KEY TRAY OPEN IF THE ERROR OCCURS, GO TO ERROR MODE DISC SKIP DISC SKIP DISC SKIP TRAY CLOSE DISC X PLAY DISC SKIP DISC Y PLAY DISC SKIP DISC Z PLAY 4.
RXD-655/755 ADJUSTMENT TUNER SECTION fL : Low-range frequency fH : High-range frequency • AM IF/RF Signal generator : 400HZ, 30%, AM modulated Test Stage Frequency Frequency Display Setting/Adjusting PartsInstrument Connection ✽ AM IF 450kHz 1620kHz T351 ✽ AM Band Coverage 522kHz (fL) : T306 1.1±0.1V...
RXD-655/755 EXPLODED VIEW (CD MECHANISM) AL SCREW : N09-5335-08 AM ø3x8 : N09-5332-08 AN ø2.6x6 : N32-2606-46 AQ ø2x3 : N30-2003-46 AR WASHER : N19-1435-05 AS ø2x5 : N86-2005-46 PWB-F PWB-B PWB-C Parts with exploded numbers larger than 700 are not supplied.
Page 27
Description Ref. No Parts No. ress Parts nation marks Parts nation marks ress ✽ E30-2915-08 AC POWER CORD QACCB0009AW00 RXD-655/755 ✽ E30-7227-08 AC POWER CORD QACCE0010AW00 EE2M ✽ E30-7227-08 AC POWER CORD QACCE0010AW00 M3M4 ✽ A02-3014-08 CABINET(TOP) GCAB-1195AWSA ✽ E30-7239-08 AC POWER CORD QACCL0005AW00 ✽...
Page 28
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 29
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 30
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 31
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 32
✽ New Parts ✽ New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.