General - Sony SLV-LF1 Service Manual

Hide thumbs Also See for SLV-LF1:
Table of Contents

Advertisement

Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries
to the diagram inside the battery
compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote
commander to operate this
VCR and a Sony TV. Buttons
on the remote commander
marked with a dot (•) can be
used to operate your Sony TV.
If the TV does not have the g
symbol near the remote sensor,
this remote commander will
not operate the TV.
To operate
Set TV/VIDEO to
VIDEO and point at the remote sensor on the VCR
the VCR
TV and point at the remote sensor on the TV
a Sony TV
Notes
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• You may not be able to use some buttons to control non-Sony TVs due to the remote
commander's signal limitations.
• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code number may
automatically reset to 01 (Sony). If your TV is not a Sony, it is recommended to
manually set the appropriate code number every time you replace the batteries.
• If you set your TV's code number correctly while the TV is turned on, the TV turns
off automatically.
SECTION 1

GENERAL

Remote sensor
TV/VIDEO
continued
5
Getting Started
7
Getting Started
This section is a translated
version of Instruction Manual
SLV-LF1AS model.
Part number: 3-067-158-11
Step 2: Setting up the remote commander (continued)
Notes
• The TV/VIDEO button selects the TV's input source (either aerial in or line in). The
button does not control this VCR.
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the table below, set the appropriate manufacturer's code
number.
1
Set
TV/VIDEO
at the top of the remote commander to
2
Hold down ?/1, and enter your TV's code number(s) using the
programme number buttons. Then release ?/1.
Now you can use the ?/1, VOL +/–, PROG +/–, programme number
buttons, ? (ten's digit) and TV/VIDEO buttons to control your TV. You
can also use the buttons marked with a dot (•) to control a Sony TV. To
control the VCR, reset
TV/VIDEO
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
Manufacturer
Code number
1
Sony
01*
,02
Akai
68
Blaupunkt
10
Ferguson
52
Grundig
11*
1
Hitachi
24
ITT/Nokia
15,16,69*
JVC
33*
Loewe
45
Mivar
09, 70
NEC
66
Panasonic
17*
1
,49
6
Getting Started
Step 3
Connecting the VCR
Connect the aerial to your VCR and TV as shown below to watch TV
programmes and VCR pictures on your TV. In addition, if your TV has
audio/video (A/V) input jacks, we recommend you connect the VCR to
your TV using an audio/video cable to get a better picture and sound.
Connecting the aerial
AERIAL OUT
Mains lead
to mains
: Signal flow
1
Disconnect the aerial cable from your TV
and connect it to AERIAL IN on the rear
panel of the VCR.
2
Connect AERIAL OUT of the VCR and
the aerial input of your TV using the
supplied aerial cable.
3
Connect the mains lead to the mains.
If the 3-pin plug does not fit into the mains outlet, detach the plug
by loosening the screw, then use the 2-pin plug inside.
8
Getting Started
1-1
SLV-LF1
TV
.
to
.
VIDEO
Manufacturer
Code number
1
1
1
Philips
06*
,07*
,08*
Saba
12,13
Samsung
22,23
Sanyo
25
Sharp
29
Telefunken
36
3
Thomson
43*
2
Toshiba
38
AERIAL IN
AERIAL IN
Aerial cable (supplied)
AERIAL
IN
OUT
AERIAL
IN
OUT

Advertisement

Table of Contents
loading

Table of Contents