Sanyo DS19310 Service Manual page 4

Table 1. ON-SCREEN SERVICE MENU
When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be checked
and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked with an * should
be changed from Initial Reference Data. (See page 3 for Initial Bus Data Setup.)
INITIAL REFERENCE
No. TITLE
DATA
001 HP
002 IAS
003 RAD
004 PT
005 ADA
006 CD
007 VS
008 RB
009 GB
010 BB
011 RD
012 BD
013 TDS
014 AF
015 BS
016 VL
017 FL
018 NIS
019 ABL
020 WP
021 GD
022 VC
023 VD
024 AG
025 SB
026 SCO
027 STI
028 SSH
029 OPT
030 OP2
031 HR
032 INP
033 STE
034 FIL
035 LSP
036 HSP
037 SPV
038 PCO
039 PTI
040 SBO
041 DRV
–
042 –
–
043 T00
↓ ↓
115 T48
INITIAL SETUP
DATA
15 14*
0 0
25 25
64 64
31 31
0 0
32 32
0 0
0 0
0 0
60 60
60 60
0 1*
0 1*
0 0
4 4
15 15
1 1
1 1
1 1
7 7
0 0
32 32
3 0*
32 32
10 7*
14 18*
8 8
0 0
0 0
24 28*
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
0 0
 
 
0 0
0 0
0 0
0 0
↓ ↓
0 0
RANGE OF DATA
0~31 Horizontal Phase (Horizontal Centering)
0, 1 IF AGC Switch
0~63 RF AGC Delay
0~127 PLL Tuning
0~63 APC Detect Adjust
0, 1 C-Diff
0~63 Vertical Size
0~255 Red Bias
0~255 Green Bias
0~255 Blue Bias
0~127 Red Drive
0~127 Blue Drive
0, 1 Trap & D (B.P.F.) Switch
0, 1 Auto Flesh
0, 1 Black Stretch
0~7 Video Level
0~31 FM Level
0, 1 N/I Switch (Black Noise Inverter)
0,1 ABL Defeat
0,1 White Peak Limiter
0~15 Green Drive Reduction
0~7 Vert. Comp
0~63 Vert. DC
0~3 AFC Gain
0~63 Sub-Brightness
0~31 Sub-Color
0~31 Sub-Tint
0~15 Sub-Sharpness
0~255 Option 1
0~255 Option 2
0~63 H-Position (OSD H-Position)
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
0~255 Sub Bright Offset
0~127 Red drive Adjustment
0~127 Blue Drive Adjustment
0~255 Red Bias Adjustment
0~255 Green Bias Adjustment
0~255 Blue Bias Adjustment
0~255 N/A
↓ ↓
0~255 N/A
— 4 —
FUNCTION
0: TV (Normal) 1: AV (IF Gain Minimum)
0: OFF 1: ON
0: OFF 1: ON
1: OFF 0: ON
1: OFF 0: ON
0: OFF 1: ON
1: OFF 0: ON
00: Auto 01: High Gain 10: Low Gain 11: Non-Gate
(See Note 1 page 5.)
(See Note 2 page 5.)
(See Note 3 page 5.)
(See Note 3 page 5.)
(See Note 4 page 5.)
(See Note 4 page 5.)
(See Note 4 page 5.)