Panasonic NV-MD10000GC Service Manual page 52

Service Manual
Diagrams and Replacement
Parts List
Digital Video Camera
NV-MD10000GC
NV-MD10000GK
Vol. 1
Table of contents
S1. About Indication of The Schematic Diagrams .......................... S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Monitor P.C.B . ...................................................................... S-2
S2.2. EVF P.C.B. ........................................................................... S-2
S2.3. Mic Jack P.C.B. .................................................................... S-2
S2.4. Front P.C.B. .......................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. EVR INT 1 Schematic Diagram ............................................. S-8
S4.3. EVR INT 2 Schematic Diagram ............................................. S-8
S4.4. Battery INT Schematic Diagram ............................................ S-9
S4.5. AV Jack Schematic Diagram ............................................... S-10
S4.6. Side R Schematic Diagram ................................................. S-11
S4.7. Side R Operation Schematic Diagram ................................ S-12
S4.8. Monitor Schematic Diagram ................................................ S-13
S4.9. EVF INT Schematic Diagram .............................................. S-14
VM0509039CE
S1. About Indication of The Schematic Diagrams
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
Name of Signal
S4.10. EVF B/L Schematic Diagram ............................................ S-14
S4.11. Handle Zoom Schematic Diagram ................................... S-15
S4.12. Mic Jack Schematic Diagram ............................................ S-15
S4.13. Zoom Schematic Diagram................................................. S-16
S4.14. Front Schematic Diagram ................................................. S-16
S4.15. S/S Power Schematic Diagram ......................................... S-17
S4.16. LCD Det Schematic Diagram ............................................ S-17
S4.17. Eject Schematic Diagram .................................................. S-17
S4.18. CCD Flex Schematic Diagram .......................................... S-18
S4.19. Holl Sensor Flex Schematic Diagram ............................... S-22
S5. Print Circuit Board .................................................................. S-23
S5.1. EVR INT 1 P.C.B . ............................................................... S-23
S5.2. EVR INT2 P.C.B. ................................................................ S-23
S5.3 Battery INT P.C.B. ............................................................... S-24
S5.4. AV Jack P.C.B . ................................................................... S-25
S5.5 Side R P.C.B. ...................................................................... S-26
S5.6 Side R Operation P.C.B. ...................................................... S-27
S5.7. Monitor P.C.B. ..................................................................... S-28
S5.8. EVF INT P.C.B. .................................................................. S-29
S5.9. EVF P.C.B . ......................................................................... S-29
S5.10. Handle Zoom P.C.B. ......................................................... S-30
Circuit name being connected.
This signal is connected
FEP
OFTR
to the EFP schematic diagram
S5.11. Mic Jack P.C.B. ................................................................. S-30
S5.12. Zoom P.C.B. ..................................................................... S-31
S5.13. Front P.C.B. ...................................................................... S-31
S5.14. S/S Power P.C.B. .............................................................. S-32
S5.15. LCD Det P.C.B. ................................................................. S-32
S5.16. Eject P.C.B. ...................................................................... S-33
S5.17. CCD Flex .......................................................................... S-34
S5.17.1. CCD Flex (Component Side) ......................................... S-34
S5.17.2. CCD Flex (Foil Side) ...................................................... S-35
S5.18. Holl Sensor Flex ................................................................ S-36
S6. Replacement Parts List ......................................................... S-37
S7. Exploded Views ...................................................................... S-44
S7.1. Frame and Casing Section(1) ............................................. S-44
S7.2. Frame and Casing Section(2) ............................................. S-45
S7.3. Camera Lens Section......................................................... S-46
S7.4. LCD Section ........................................................................ S-47
S7.5. Video Mechanism Section ................................................... S-48
S7.6. Packing Parts and Accessories Section .............................. S-49
S-1
HAVE THE SPECIAL CHARACTERISTICS