ICs inside the unit. 3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. DEH-P5850MP/XN/ES...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-P5850MP/XN/ES...
CD:0.36dBs CL220SRCTS:ES CL220PGC:CN,GS PANEL UNIT For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 12k ohms 10k ohms *Capacitors Code Practical value 0.01uF 101/10 100uF/10V DEH-P5850MP/XN/ES...
Page 15
Therefore, when replacing, be sure to use parts of Symbol indicates a capacitor. identical designation. No differentiation is made between chip capacitors and discrete capacitors. > CD:9.65dBs FM,AM:-0.90dBs CD:10.01dBs IP-Bus:9.30dBs > 600 H > FUSE CEK1208 BACK UP FM,AM:21.1dBs CD:36.10dBs IP-Bus:36.30dBs DEH-P5850MP/XN/ES...
Page 16
104:GS 104:ES,CN UNIT TUNER FM/AM DEH-P5850MP/XN/ES...
3.4 CD MECHANISM MODULE(GUIDE PAGE) PICKUP UNIT(P10.5)(SERVICE) SWITCHES: CD CORE UNIT(S10.5COMP1) S901:HOME SWITCH..ON-OFF S903:DSCSNS SWITCH..ON-OFF S904:12EJ SWITCH.....ON-OFF S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. CD DRIVER M1 CXC6742 SPINDLE MOTOR M2 CXC4026 LOADING/CARRIAGE MOTOR DEH-P5850MP/XN/ES...
Page 23
FOCUS SERVO LINE are expressed as : TRACKING SERVO LINE ← ← CARRIAGE SERVO LINE 0.022 R022 SPINDLE SERVO LINE CD CORE UNIT(S10.5COMP1) + 3.3 V REGULATOR CD3VON(MCKRQ) SRAMLEVEL2 ADENA SRAMLEVEL1 SRAMLEVEL0 (S904) CD CONTROLLER (S905) CN651 DEH-P5850MP/XN/ES...
Page 28
200 mV/div 500 mV/div ! TE 500 mV/div 8 TIN 500 mV/div CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation (Wider) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: Normal Normal Normal DEH-P5850MP/XN/ES...
Page 29
500 mV/div 4 LOEJ 3 12SNS 8 TIN 5 V/div 5 V/div 500 mV/div CD-DA → CD-ROM mode change(Band key) 12 cm CD Eject operation 8 cm CD Eject operation Ref.: Ref.: Ref.: REFO Mode: Mode: Mode: Normal Normal Normal DEH-P5850MP/XN/ES...
Page 30
7 CIN 8 TIN 500 mV/div 1 V/div 8 TIN ! TE 500 mV/div 1 V/div 9 FIN 1 V/div CD-ROM → CD-DA mode change(Band key) Black dot(800 µm) during play Ref.: Ref.: REFO REFO Mode: Mode: Normal Normal DEH-P5850MP/XN/ES...
For further information for WIRED respective destinations, be sure REMOTE IP-BUS to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams Capacitor Connector SIDE A SIDE B P.C.Board Chip Part CN901 DSENS DEH-P5850MP/XN/ES...
Page 33
SIDE A REAR OUT ANTENNA JACK CN651 CN1950 FRONT DEH-P5850MP/XN/ES...
4.3 CD CORE UNIT(S10.5COMP1) SIDE A CD CORE UNIT(S10.5COMP1) PICKUP UNIT(P10.5)(SERVICE) CN651 REFO1 HOME CN901 LOADING /CARRIAGE MOTOR SPINDLE MOTOR IC203 IC301 DEH-P5850MP/XN/ES...
Page 39
SIDE B CD CORE UNIT(S10.5COMP1) 12EJ DSCSNS DEH-P5850MP/XN/ES...
Page 42
RS1/16S153J R 812 (B,119,29) RS1/16S102J R 351 (B,145,108) (ES) RS1/16S821J R 813 (A,73,17) RS1/16S1R0J R 352 (B,145,119) (ES) RS1/16S821J R 814 (B,108,24) RS1/16S222J R 815 (A,104,33) RS1/16S473J R 353 (B,140,122) RS1/16S821J R 354 (B,139,119) RS1/16S821J R 816 (B,112,25) RS1/16S473J DEH-P5850MP/XN/ES...
Page 43
C 204 (A,77,101) CEJQ4R7M35 C 651 (A,14,55) CEJQ101M16 C 205 (A,83,75) CEJQ4R7M35 C 652 (B,87,30) CKSRYB152K50 C 206 (A,83,101) CEJQ4R7M35 C 653 (B,85,30) CKSRYB152K50 C 207 (A,89,75) CEJQ4R7M35 C 654 (B,66,35) CCSRCH470J50 C 208 (A,90,102) CEJQ4R7M35 C 658 (B,83,22) CKSRYB104K16 DEH-P5850MP/XN/ES...
Page 44
R 1992 (B,108,24) RS1/16S101J S 1908 (A,14,15) Push Switch CSG1133 R 1993 (B,94,29) RS1/16S101J S 1909 (A,68,6) Push Switch CSG1135 R 1994 (B,94,32) RS1/16S101J S 1910 (A,18,9) Push Switch CSG1135 R 1995 (B,63,9) RS1/16S473J S 1911 (A,156,35) Push Switch CSG1135 DEH-P5850MP/XN/ES...
Page 45
R 1962 (B,73,26) RS1/16S392J S 1904 (A,28,37) Push Switch CSG1112 R 1963 (B,68,31) RS1/16S393J S 1905 (A,7,22) Push Switch CSG1186 R 1980 (B,78,8) RS1/16S473J S 1906 (A,14,30) Switch CSG1108 R 1991 (B,107,22) RS1/16S101J S 1907 (A,22,22) Push Switch CSG1186 DEH-P5850MP/XN/ES...
Page 46
R 729 (B,20,48) RS1/16SS223J R 730 (B,20,46) RS1/16SS473J Unit Number : CWX3176 Unit Name : CD Core R 740 (A,38,59) RS1/16SS222J R 746 (A,13,38) RS1/16SS104J Unit(S10.5COMP1) R 750 (A,40,66) RS1/16SS473J R 902 (A,20,36) RS1/16SS221J MISCELLANEOUS R 905 (A,21,36) RS1/16SS221J DEH-P5850MP/XN/ES...
Page 47
C 703 (B,28,42) CKSSYB103K16 C 706 (B,34,43) CKSSYB104K10 C 707 (A,36,57) CKSSYB104K10 C 714 (A,24,41) CKSSYB104K10 C 722 (B,29,45) CKSQYB475K6R3 C 903 (B,14,54) CKSSYB471K50 C 907 (B,14,62) CKSSYB103K16 Miscellaneous Parts List Pickup Unit(P10.5)(Service) CXX1942 Motor Unit(SPINDLE) CXC6742 Motor Unit(LOADING/CARRIAGE) CXC4026 DEH-P5850MP/XN/ES...
1k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-P5850MP/XN/ES...
Page 49
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. DEH-P5850MP/XN/ES...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-P5850MP/XN/ES...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. DEH-P5850MP/XN/ES...
KEYBOARD UNIT(SIDE B) Digital Multi-Meter <When the OEL Unit has been replaced> 1. Use VR1970 to adjust the resistance between TP1 and TP3 to 6.2 kΩ. 2. Use VR1971 to adjust the resistance between TP2 and TP3 to 6.2 kΩ. DEH-P5850MP/XN/ES...
Grille Assy. Fig.1 Grille Assy Removing the Tuner Amp Assy (Fig.2) Remove the screw. Remove the three screws. Straighten the tabs at three locations indicated. Remove the screw and then remove the Tuner Amp Assy. Tuner Amp Assy Fig.2 DEH-P5850MP/XN/ES...
Page 55
Upper Frame. 3. While lifting the Carriage Mechanism, remove it from the three Dampers. Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. Damper Damper Carriage Mechanism Lower Frame DEH-P5850MP/XN/ES...
Page 56
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw. Poly Washer Change Arm Pickup Lock Arm Inner Holder Feed Screw Planet Gear Pickup Rack Chassis Pickup DEH-P5850MP/XN/ES...
7.1.2 CONNECTOR FUNCTION DESCRIPTION 1 0 A DEH-P5850MP/XN/ES...
Page 58
Ground for 1.6 V digital circuits D1.GND Output of 33.8688 MHz(CLK for SDRAM) C33M DRAM cs (rcs) RA11 Output of DRAM address 11 Output of DRAM CKE (CKE) Output of DRAM ras Output of DRAM lower cas(LDQM) cas)(LDQM) cas!(UDQM) Output of DRAM upper cas(UDQM) DEH-P5850MP/XN/ES...
Page 59
Output of TE Output of LD Input of PD Ground for digital circuits D.GND * UPD63763CGJ IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. DEH-P5850MP/XN/ES...
Page 60
VD power supply control output VDCONT CD LSI serial data input CD LSI serial data output CD LSI serial clock output xwait CD LSI wait control signal input CD LSI address strobe output XASTB Address/data Bus 0 Not used DEH-P5850MP/XN/ES...
Page 61
VD power supply short sense input Not used DSCSNS * PE5505A Format meaning C MOS NJM2886DL3-33 Thermal Protection Bandgap Reference CONTROL GP1UX30RK - Block Diagram - Pin Layout Limiter B.P.F Demodulato Integrator Comparator vout GND VCC GND VCC vout DEH-P5850MP/XN/ES...
Page 62
D15-0 Not used ks@-^ key strobe 2-6 88-92 Not used A/D converter GND input AVSS Not used A/D converter reference voltage VREF A/D converter power supply input AVCC flbusy Not used Not used FWRST Restart signal for IC rewriting DEH-P5850MP/XN/ES...
Page 63
* PEG203A Format meaning C MOS Nch open drain * PD8156A HA12241FP -BUS +BUS BIAS DRIVER OUTPUT (current) RECEIVER OUTPUT R out DEH-P5850MP/XN/ES...
Page 65
Not used Not used 47-56 EVol mute EMUTE Not used 58,59 Power supply input Not used Not used 63-66 Output for dark current reduction circuit DALMON Not used tunpce@ TUNER : Chip enable output(EEPROM) TUNER : Chip enable output(PLL) TUNPCE1 DEH-P5850MP/XN/ES...
Page 66
Not used AVSS A/D converter GND input TUNER : Signal level input A/D converter reference voltage VREF A/D converter power supply input AVCC TUNER : Data input(PLL) TUNPDI TUNER : Data output(PLL) TUNPDO TUNER : Clock output(PLL) TUNPCK * PEG146A DEH-P5850MP/XN/ES...
Page 67
22 AUDIOGND audio ground Ground of audio block 23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output DEH-P5850MP/XN/ES...
In case of the above signal, the communication with Grille microcomputer may fail. Source keys If the time interval is not 300 msec, the oscillator operative may be defective. Source ON SYSPW←H Pin 1 Completes power-on operation. (After that, proceed to each source operation) DEH-P5850MP/XN/ES...
Page 71
1. Attach the holders to both sides of the front panel. Holder(CXX1645) Holder(CXX1644) 2. Replace the front panel to the unit. 3. Flip the holders into upright positions. 4. Fix the front panel to the unit using fixing screws. Fixing screw(XXX7020) Fixing screw(XXX7020) DEH-P5850MP/XN/ES...
Page 74
CD Mechanism Module Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 g p p DEH-P5850MP/XN/ES...