Optoma HD82 Serivce Manual
  1. Manuals
  2. Brands
  3. Optoma Manuals
  4. Projector
  5. Theme Scene HD82
  6. Serivce manual

Optoma HD82 Serivce Manual

Hide thumbs Also See for HD82:
Table of Contents

Advertisement

Quick Links

See also: User Manual

SERVICE MANUAL

Date
2008.12.29
2009.01.06
2010.02.22
Copyright February, 2010. All Rights Reserved P/N:36.8AF05G001
Qiue
SI :
TSE:
HD82/HD8200
Revise Version
V1.0
V2.0
V3.0
(Change "press power → left → left → up" to "press
power off → left → left → up"
Modify CH4 "Defect specification table"
Check:
Description
Initial Issue
Modify CH2,CH4
Approved:

Advertisement

Table of Contents
loading

Related Manuals for Optoma HD82

Summary of Contents for Optoma HD82

  • Page 1: Service Manual

    SERVICE MANUAL HD82/HD8200 Date Revise Version Description 2008.12.29 V1.0 Initial Issue Modify CH2,CH4 2009.01.06 V2.0 (Change “press power → left → left → up” to “press power off → left → left → up“ 2010.02.22 V3.0 Modify CH4 “Defect specification table“...
  • Page 2 Preface This manual is applied to HD82/HD8200 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products.

  • Page 3: Table Of Contents

    Disassemble Lamp Driver Module 2-13 Disassemble DMD Blower 2-14 Disassemble Optical Engine Blower 2-15 Disassemble Engine Module 2-16 Disassemble Color Wheel Module 2-16 Disassemble Lamp Blower Duct Module 2-18 Disassemble DA Cover 2-18 Disassemble DA Motor Module 2-19 HD82/HD8200 Confidential...
  • Page 4 2-28 Re-write Lamp Usage Hour 2-29 Chapter 3 Troubleshooting LED Lighting Message Main Procedure Chapter 4 Function Test & Alignment Procedure Test Equipment Needed Service Mode OSD Reset Test Condition Test Inspection Procedure PC MODE Video Performance Calibration HD82/HD8200 Confidential...
  • Page 5 EDID Introduction Equipment Needed Setup Procedure(VGA & DVI-D Port) EDID Key-In Procedure(VGA & DVI-D Interface) Setup Procedure (HDMI 1 Port & HDMI 2 Port ) EDID Key-In Procedure(HDMI 2 Interface) Appendix A Exploded Image Appendix B Serial Number System Definition PCBA Code Definition 23 HD82/HD8200 Confidential...

  • Page 6: Chapter 1 Introduction

    ● Philips ��0W with �IDI ● Operating�� 5°C��35°C (Satisfied engineering specification & Temperature functions) ● Storage�� ��10°C���� �0°C 1� DMD Chip ● Single 0.�5�� DC3 1080P DMD with DDP30�1 x � Single 0.�5�� DC3 1080P DMD with DDP30�1 x � HD82/HD8200 Confidential...

  • Page 7: Compatible Mode

    800×�00 5� � 800×�00 � � �0 800×�00 � � SXGA 7� 800×�00 � � 800×�00 � � 10�4×7�8 � � �0 10�4×7�8 � � 10�4×7�8 � � 10�4×7�8 � 1�80×7�8 � � �0 WXGA 1280×800 � �0 Confidential HD82/HD8200...
  • Page 8 � 1�80×10�4 �0 � 1�80×10�4 � SXGA� 1400×1050 �0 � UXGA 1�00×1�00 �0 � iMAC 10�4×7�8 �0 � Note: "V" expressed support this type of signal and "X" expressed that does not support this type of signal. Confidential HD82/HD8200 1��3...

  • Page 9: Disassembly Process

    4. Hex Sleeves 5 mm 5. Tweezers 6. HD82 unit * Before you start: This process is protective level II. Operators should wear electrostatic chains. * Note: If you need to replace the main board, you have to record the lamp usage hour.

  • Page 10: Disassemble Lamp Cover Module

    2. Push the lamp cover switch to the open state (as the red oval-shaped circle). 3. Disassemble lamp cover module. 2-3 Disassemble Lamp Module 1. Unscrew 2 screws (as red circle) on the lamp module. 2. Take off lamp module from the projector. HD82/HD8200 Confidential...

  • Page 11: Disassemble Bottom Cover Module

    2. Unscrew 6 screws from the bottom cover (as red circle). 3. Disassemble the bottom cover module. 2-5 Disassemble Formatter Board Module 1. Unscrew 5 screws (as red circle) and 2 Hex screws (as yellow square) from the formatter board. HD82/HD8200 Confidential...
  • Page 12 2. Disassemble formatter board as arrow shows. 3. Unplug 2 connectors (as yellow square). 4. Disassemble formatter board. HD82/HD8200 Confidential...

  • Page 13: Disassemble Main Board And I/O Board Module

    2-6 Disassemble Main Board and I/O Board Module 1. Unscrew 3 screws (as red circle). 2. Unplug 1 connector (as yellow square). 3. Unscrew 6 Hex screws (as red circle). 4. Disassemble the main board module. HD82/HD8200 Confidential...

  • Page 14: Disassemble Lens Ring Module

    6. Disassemble the I/O board from main board module. 2-7 Disassemble Lens Ring Module 1. Clockwise rotate the lens ring about 15 degrees (from left image to right image as the red oval-shaped circle), take off the lens ring. HD82/HD8200 Confidential...

  • Page 15: Disassemble Top Cover Module

    3. Pushing back (as red arrow) , disassemble top cover module. 2-9 Disassemble Top Shielding 1. Unscrew 7 screws (as red circle). 2. And then unscrew 3 screws (as green circle). 3. Disassemble top shielding. HD82/HD8200 Confidential...

  • Page 16: Disassemble Right Cover Module

    Cover Module 1. Unplug 2 connectors (as red square). 2. Tear 1 mylar off (as yellow oval-shaped circle). 3. Unscrew 1 screw (as red circle). 4. Unscrew 2 screws (as red circle). 5. Unscrew 2 screws (as red circle). HD82/HD8200 Confidential...
  • Page 17 8. Unscrew 2 screws (as green circle), disassemble lamp latch. . Use the tweezers to separate 2 tenons (as red circle). 10. Disassemble front IR lens module. 11. Unscrew 1 screw (as red circle). 12. Disassemble IR lens right and IR transmitter board. HD82/HD8200 Confidential...

  • Page 18: Disassemble Daught Board Module

    Photo sensor board (for DA motor, 3 pin, black) DA motor (4 pin) Color wheel System fan (3 pin, green) Lamp driver wire (5 pin, black) 0 DMD blower on LVPS (3 pin)  Formatter board (30 pin, black) 2 Thermal sensor board HD82/HD8200 Confidential 2-0...

  • Page 19: Disassemble System Fan Module

    2-12 Disassemble System Fan Module 1. Unscrew 5 screws (as red circle). 2. Turn back the system fan module and unscrew 2 screws (as red circle). 3. Disassemble system fan module. HD82/HD8200 Confidential 2-...
  • Page 20 Note: Take the Fan Module as the right gesture, Avoid pressing the middle of the Fan or Blower with great strength. Make sure Fan or Blower handle method as right image. the wrong gesture the right gesture HD82/HD8200 Confidential 2-2...

  • Page 21: Disassemble Lamp Driver Module

    2-13 Disassemble Lamp Driver Module 1 .Unscrew 3 screws (as red circle) to disassemble lamp driver module. 2. Unplug 1 connector (as red square). 3. Disassemble lamp driver module. HD82/HD8200 Confidential 2-...

  • Page 22: Disassemble Dmd Blower

    2 screws (as red circle). 5. Disassemble lamp driver module. 2-14 Disassemble DMD Blower 1. Unscrew 2 screws (as red circle). 2. Disassemble DMD blower and rubber. Note: Avoid pressing the middle of the Blower or Fan with great strength. HD82/HD8200 Confidential 2-...

  • Page 23: Disassemble Optical Engine Blower

    Engine Blower 1. Unscrew 4 screws (as red circle). 2. Disassemble optical engine blower. Unscrew 2 screws (as red circle). 4. Disassemble optical engine blower. Note: Avoid pressing the middle of the Blower or Fan with great strength. HD82/HD8200 Confidential 2-15...

  • Page 24: Disassemble Engine Module

    1. Unscrew 5 screws (as red circle). 2. And then unscrew 2 screws (as red circle). 3. Disassemble engine module. 2-17 Disassemble Color Wheel Module 1. Unscrew 3 screws (as red circle). 2. Disassemble color wheel cover. HD82/HD8200 Confidential 2-...
  • Page 25 3. Unscrew 2 screws (as red circle). 4. Disassemble color wheel module. 5. Unscrew 1 screw (as red circle). 6. Disassemble color wheel and photo sensor board. HD82/HD8200 Confidential 2-17...

  • Page 26: Disassemble Lamp Blower Duct Module

    2-18 Disassemble Lamp Blower Duct Module 1. Unscrew 1 screw (as red circle). 2. Disassemble lamp blower duct module. 2-19 Disassemble DA Cover 1. Unscrew 3 screws (as red circle). 2. Disassemble DA cover. HD82/HD8200 Confidential 2-8...

  • Page 27: Disassemble Da Motor Module

    2-20 Disassemble DA Motor Module 1. Unscrew 2 screws (as red circle). 2. Disassemble DA motor module. 3. Unscrew 1 screw (as red circle). 4. Disassemble DA motor and photo sensor board. HD82/HD8200 Confidential 2-...

  • Page 28: Disassemble Rod Module

    2-21 Disassemble Rod Module 1. Unscrew 3 screws (as red circle). 2. Disassemble rod module. 2-22 Disassemble Heat Sink Module 1. Unscrew 4 screws (as red circle). 2. Disassemble heat sink module. HD82/HD8200 Confidential 2-20...

  • Page 29: Disassemble Dmd Module

    1. Unscrew 4 Hex screws (as red circle). 2. Disassemble DMD module. 3. Unscrew 1 screw (as red circle), disassemble DMD board and shielding. 2-24 Disassemble Focus Ring 1. Unscrew 3 screws (as red circle). 2. Disassemble focus ring. HD82/HD8200 Confidential 2-2...

  • Page 30: Disassemble Zoom Ring Module

    2-25 Disassemble Zoom Ring 1. Unscrew 2 screws (as red over-shaped circle). 2. Disassemble zoom ring. 2-26 Disassemble Lamp Blower Module 1. Unscrew 2 screws (as red circle). 2. Disassemble lamp blower and rubber. HD82/HD8200 Confidential 2-22...

  • Page 31: Disassemble Air Duct Module

    2-27 Disassemble Air Duct Module 1. Unscrew 3 screws (as red circle). 2. Disassemble air duct module. 2-28 Disassemble Left Cover Module 1. Unscrew 5 screws (as red circle). 2. Remove LVPS module. 3. Unscrew 3 screws (as red circle). HD82/HD8200 Confidential 2-2...
  • Page 32 4. Then unscrew 2 screws (as red circle). 5. Disassemble left cover module. 6. Unscrew 3 screws (as red circle), unplug 1 connector (as yellow square). 7. Disassemble LED module. HD82/HD8200 Confidential 2-2...

  • Page 33: Disassemble Lvps Module

    8. Use the tweezers to separate 2 tenons (as red circle). . Disassemble IR lens left and IR sensor board. 2-29 Disassemble LVPS Module 1. Remove LVPS module. 2. Tear 2 mylars off (as yellow square). 3. Unscrew 2 screws (as red circle). HD82/HD8200 Confidential 2-25...

  • Page 34: Disassemble Thermal Sensor Board

    4. Unplug 5 connectors (as yellow square). 5. Disassemble LVPS module. 2-30 Disassemble Thermal Sensor Board 1. Tear 1 mylar off (as yellow square). 2. Unscrew 1 screw (as red circle). 3. Disassemble thermal sensor board. HD82/HD8200 Confidential 2-2...

  • Page 35: Disassemble Bottom Cover Shielding Module

    2-31 Disassemble Bottom Cover Shielding Module 1. Unscrew 20 screws (as red circle). 2. Disassemble bottom cover shielding. 2-32 Disassemble Ceiling Base Module 1. Unscrew 6 screws (as red circle). 2. Disassemble IO base and ceiling base module. HD82/HD8200 Confidential 2-27...

  • Page 36: Rod Adjustment

    - It should not have any abnormal color at the rim of the image by estimating through the eyes. Note: - To avoid over adjusting the rod. - After the operation,please use the glue to fix the screws. HD82/HD8200 Confidential 2-28...

  • Page 37: Re-Write Lamp Usage Hour

    Hour 1. First, input a signal to the projector. 2. Get into service mode - Press power off→left→left→up on remote controller to get into service mode. 3. Use “up” and “down” key to move cursor to “Exit”. HD82/HD8200 Confidential 2-2...
  • Page 38 - Use “left” and “right” key of the ''image- shift'' to re-write “Lamp Hours”. Note: press ''left'' key of the 'image-shift'', the lamp hour will increase 20 hours; press ''right'' key of the ''image-shift'', the lamp hour will decrease 20 hours. 5. Chose”Exit” Left Right HD82/HD8200 Confidential 2-0...

  • Page 39: Led Lighting Message

    Power on with OSD (Press power button) Power on without OSD Thermal switch error (Red) Fan lock error Flashing OSD shows “Fan Fail” (Red) Lamp error (Lamp, LVPS,or color wheel fail) (Orange) Power off (Cooling) light off light on HD82/HD8200 Confidential...

  • Page 40: Main Procedure

    - Check Daughter Board Auto Shut Down - Check Formatter Board - Check Color Wheel - Check Photo Sensor Board b. Power LED light on blue, temp LED flash red - Check Fan - Check Photo Sensor Board HD82/HD8200 Confidential...
  • Page 41 - Check Fan Module Machanical Noise - Check DA Motor - Check if the Formatter Board and the DMD Board are assembled properly - Check Main Board Line Bar/Line Defect - Check DMD Board - Check DMD Chip HD82/HD8200 Confidential...
  • Page 42 (Out of spec.) - Check DMD Chip - Check Engine Module - Ensure that the signal cables and source work as well - Check Main Board - Check Daughter Board Garbage Image - Check Formatter Board - Check DMD Board HD82/HD8200 Confidential...
  • Page 43 - Check IR receiver - Check Main Board - Check Daughter Board - Do “Reset(All data)” of the OSD Menu - Check Main Board Function Abnormal - Check Formatter Board - Check DMD Board - Check Daughter Board HD82/HD8200 Confidential...

  • Page 44: Function Test & Alignment Procedure

    1. After final QC step, we have to erase all saved change again and restore the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting: (1) Please get into OSD menu. (2) To execute "Reset" function. HD82/HD8200 Confidential...

  • Page 45: Test Condition

    Press right key to adjust the time (50) Lamp Off (Min) Press right key to adjust the time (10) Set burn in cycle Press right key to adjust the cycle After setting up the time, choose ''Get into Burn-In Mode'' and hit enter HD82/HD8200 Confidential...

  • Page 46: Defect Specification Table

    B≤2 Unstable pixel (dots) Any pattern A+B=0 Adjacent pixel (dots) Any pattern A+B=0 Bright blemish (Dirty) Gray 10 pattern B≤4 (diameter<1 inch) Dark Blemish(Dirty) Blue 60 pattern B≤4 (diameter<1 inch) Bright pixel on frame Gray 10 pattern ≤1 HD82/HD8200 Confidential...

  • Page 47: Test Inspection Procedure

    (2) Select "Tracking" function and use right or left arrow key to adjust the value to minimize video flicker. - Adjust Resync or Frequency/Tracking/H. Position/V. Master Position to the inner screen. HD82/HD8200 Confidential...
  • Page 48 - Test Pattern: gray 10 pattern Inspection item - Bright pixel check. - Adjacent pixel. - Adjacent pixel. Criteria - Bright pixel is unacceptable. - Adjacent pixel is unacceptable. - Adjacent pixel is unacceptable. - Ref. Defect specification table. Gray 10 HD82/HD8200 Confidential...
  • Page 49 - Test equipment: video generator. - Test signal: analog 1920 x 1080@60Hz analog 1920 x 1080@60Hz - Test Pattern: full screen Inspection item - Focus check Criteria - From screen 1.98 M via visual to check the focus, HD82/HD8200 Confidential...
  • Page 50 4 color levels.) - Gray level should not have abnormal color or heavy lines. - The PC mode functionally sure be workable in- clude support format with frequency and auto detected functional will be workable SMPTE RP-133 HD82/HD8200 Confidential...

  • Page 51: Video Performance

    3. HDTV/ Component Procedure - Test equipment: DVD player - Test signal: Ycbcr/YPbPr Inspection item - HDTV performance test Inspection Distance - 1.5M ~2.0M Criteria - Check any abnormal color, line distortion or any noise on the screen. HD82/HD8200 Confidential...

  • Page 52: Calibration

    4-8 Calibration 1. Video calibration Procedure - Test equipment: video generator. - Once formatter board is changed, Video calibra- tion should be done as well. (1) Test signal: 720p (2) Test Pattern: SMPTE BAR SMPTE BAR HD82/HD8200 Confidential...
  • Page 53 Criteria - Color levels should be sufficient and normal. (the unidentified color levels on both left and right sides should not be over 2 color levels.) - Gray level should not have abnormal color or heavy lines. HD82/HD8200 Confidential 4-0...

  • Page 54: Da Calibration

    - Select “Spoke Test” 2. Brightness Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9. - Follow the brightness formula to calculate brightness values. ☼ Brightness Formula Avg. (P1~P9)*1.1m Criteria ● 470 ANSI lumen HD82/HD8200 Confidential 4-...
  • Page 55 Full black pattern - Use CL100 to measure brightness values of P1~P9 (see image: full white). - Follow the Uniformity formula to calculate average values. ☼ Uniformity Formula JBMA Uniformity = Avg. (P1, P3, P7, P9)/P5X100% Criteria ● 70% HD82/HD8200 Confidential 4-2...

  • Page 56: Others

    It should be locked in the correct place. Plastic Parts All plastic parts can not be broken and damaged. Safety or warning All safety and warning labels should be visible, label including all contents. All interface connectors should be complete and Connector workable. HD82/HD8200 Confidential 4-13...

  • Page 57: Firmware Upgrade

    Software : (DDP 3021) HD82_FW_xxx.bin HD82_8051_xxx.hex eZISP_3.1 zip Note: ''xxx'' represent software version Hardware : - HD82 - Power Cord (P/N 42.50115G001) - RS-232 9 Pin Cable (Pin to Pin, M-M) (P/N 42.00271G001 ) - 8051 Fixture - VGA cable: 42.87305G001 - PC...

  • Page 58: Setup Procedure

    5-2 Setup Procedure 1. Plug the power cord, connect the projector and PC with RS-232 cable Note: The system fan and the light will not operate. 5-3 Firmware Upgrade Procedure 1. Double click the folder ''HD82_FW_xxx.bin''. 2. Execute "FlashUpgrader.exe". HD82/HD8200 Confidential...
  • Page 59 Note: Don’t use other baud rate than ''115200'', or else the program may not work. (5) Finally select ''flash''. 4. ''Waiting for target reset..'' appears on the screen. 5. Press the power button, then Firmware upgrade process begins. HD82/HD8200 Confidential...
  • Page 60 6. Firmware upgrade process will take about 5 minutes. 7. When Firmware upgrade process is finished, the projector will turn on automatically, then close FlashUpgrader program to finish firmware upgrade. 8. Then get into the service mode to check the firmware version. HD82/HD8200 Confidential...

  • Page 61: Port95Nt.exe Installation

    5-4 Port95nt.exe Installation Note: We installing ''Port95nt.exe'' is to upgrade 8051 firmware 1. Choose “Port95nt Setup” Program. 2. Click “Next” button 3. Read “Software License Agreement”. - Click "Yes" button. 4. Click “Next” button. 5. Click “Next” button HD82/HD8200 Confidential...
  • Page 62 6. Choose the type of setup. - Click “Next” button 7. Read “Software License Agreement”. - Click "Yes" button. 8. Click “Next” button. 9. Click “Finish” button. HD82/HD8200 Confidential...

  • Page 63: 8051 Firmware Upgrade Procedure

    3. Connect USB Port of 8051 fixture with USB Port of PC, two LED will light on and appear green. Note: When PC detects the USB driver, the USB driver icon will show out (as the green square). 4. Double click ''eZISP_3.1'' program. HD82/HD8200 Confidential...
  • Page 64 5. Then select '' Security ”. 6. Key in the security number as 7c, b0, 83 7. Click ''OK'', then will show ''Security Input 'Success' ”, Click ''eZISP'' to leave this stage. HD82/HD8200 Confidential...
  • Page 65 8. Select “Product” and choose “MTV312M64'' 9. Click “Load MCU” and select software ''HD82_8051_xxx.hex'' and double click it, then the '' Program status'' item will show ''Load MCU.HEX File...Success'' and the ''File Information'' will show out. HD82/HD8200 Confidential...
  • Page 66 USB driver directly. 2. If the fixture version is V31, you need to press the “switch” once on the fixture as the red circle. 3. The fixture version is on the IC as right picture. HD82/HD8200 Confidential 5-0...

  • Page 67: Edid Upgrade

    Note: If a display device has digital input ports, like DVI or HDMI, but without EDID in its main board and formatter board, the display device will show no image while the input source is digital signal. HD82/HD8200 Confidential...

  • Page 68: Equipment Needed

    - Generic Fixture :80.00001.001 for EDID Key-in (Fixture: JP3 must be closed) - Power cord (P/N 42.50115G001) - RS-232 Cable (pin to pin, F-M): 42.83618G001 - Monitor - PC - DVI cable: 42.83N06G001 - VGA cable: 42.87305G001 - Power adapter for fixture: 47.57702G001 - DVI-HDMI adapter: 42.82B13G001 HD82/HD8200 Confidential...

  • Page 69: Setup Procedure(Vga & Dvi-D Port)

    (VGA & DVI-D Interface) 1. Click on "EDID" to execute EDID program EDID program 2. Choose model - Select the ‘’COM’’ Port which you are using. - Click on "Model". - Choose the source file "HD82_EDID_xx.ini" and double click it. HD82/HD8200 Confidential...
  • Page 70 5. Change the cable to Digital - When the message “Please change the cable to Digital” is appeared on the screen, click "OK" button. 6. When the EDID program is completed, a message "OK" will appear on the screen. HD82/HD8200 Confidential...
  • Page 71 "Read" button. - EDID information will show out. 8. Read EDID "Digital" information - If EDID information is correct, select "Digital" in the Read item, then click the "Read" button. - EDID information will show out. HD82/HD8200 Confidential...

  • Page 72: Setup Procedure (Hdmi 1 Port & Hdmi 2 Port )

    - Power on fixture - Plug Power Cord to projector. 6-6 EDID Key-In Procedure (HDMI 2 Interface) 1. Choose model - Select the ‘’COM’’ Port which you are using. - Click on "Model." - Choose the source file "HD82_EDID_xx.ini''. HD82/HD8200 Confidential...
  • Page 73 4. Read EDID "Digital" information - When the EDID program is completed, a message "OK" will appear on the screen If EDID information is correct, select "Digital" in the Read item, then click the "Read" button. EDID information will show out. HD82/HD8200 Confidential...
  • Page 74 Appendix A D.C.HD82 HD82/HD8200 Confidential...
  • Page 75 ASSY. LAMP DRIVER HD82 49.83M03G001 GB1205PKV1-8AYB2079.R.GN 70.8AF23G00 ASSY. OPTICAL BLOWER HD82 70.8AF22G00 ASSY. SESTEM FAN HD82 6.8AF4G00 CONNT BOARD BRACKET SECC 0.6T HD82 80.8AF08G00 PCBA DAUGHTER BD FOR HD82 75.8AF02G00 BUY ASSY INTERLOCK SWITCH HD82 51.89S18G002 INTERLOCK SWITCH HOLDER PC ADHESIVE M209X 75.8AF04G00...
  • Page 76 Assy Lamp Adjustable Module HD82 HD82/HD8200 Confidential...
  • Page 77 6.0006G00 LOCK SCREW PAN MECH M3*8.5-3.5 Ni 5.8AF0G00 LAMP CHANGER PLATE VP22 6.8AF2G00 LAMP BLOWER INSIDE DUCT VP22 42.0043GG00 W.A. 2P#22 MALE 6KV 200C 140mm FOR LAMP VP22 87.FL431G005 WASHER FLAT 8*3.2*0.5 NI 52.83F2G00 LAMP RUBBER HD72 6.8AF09G00 LAMP ADJUSTABLE HOLDER E20.6 VP22 HD82/HD8200 Confidential...
  • Page 78 Assy Left Cover Module For HD82 Item Description Parts Supply 5.8AF8G00 SIDE COVER-L HD82 80.8AF05G00 PCBA IR SENSOR BD FOR HD82 5.8AF26G00 IR LENS L HD82 5.8AF24G00 LED LENS HD82 5.8AF34G00 POWER KEY AND IR LENS-HD82 80.8AF09G00 PCBA LED BD FOR HD82 85.WA123G060...
  • Page 79 Assy Right Cover Module For HD82 Item Description Parts Supply 70.8AF27GR01 ASSY SIDE COVER-RIGHT HD82(SERVICE) 5.8AF7G00 SIDE COVER R HD82 5.8AF30G00 LAMP LATCH HD82 80.85E05G001 PCBA FRONT IR SENSOR BD DV11 5.8AF27G00 IR LENS R HD82 5.8AF28G00 IR LENS S HD82 85.3A522G040...
  • Page 80 Assy Engine Color Wheel Module For HD82 Item Description Parts Supply 70.8AF26GR01 ASSY COLOR WHEEL MODULE (SERVICE) 6.8AF22G00 CW HOLDER YO 4x VP22 23.8AF9G0 CW Φ58 R64G62B54R64G62B54 YO 52.8365G00 COLOR WHEEL DISC RUBBER, EzPro755 COLOR WHEEL SHOULDER SCREW NICKEL 6.83628G002 M2*4.8 FILLIST...
  • Page 81 Assy Engine Module For HD82 HD82/HD8200 Confidential...
  • Page 82 RUBBER BLOWER 595925 6.89626G00 HEATSINK SCREW EP759 6.89630G00 HEATSINK SPRING EP759/PD726 5.8AF07G00 LENS SHIFT RING VP22 80.8AF02G00 PCBA DMD BD ENTEK FOR HD82 6.8AF07G00 DMD HEATSINK VP22 70.8AF3G00 ASSY RELAY MODULE VP22 48.8AF0G00 DMD TYPE-A 1080P 0.65” 2xLVDS 85.A526G30 SCREW PAN HEAD M2.6*13 NYLOK NICKEL 70.8AF04G00...
  • Page 83 70.8AF31GR01 ASSY ENGINE DA MODULE VP22 FOR HD82(SERVICE) 6.8AF58G00 DA SHOULDER SCREW-HD82 52.8365G00 COLOR WHEEL DISC RUBBER, EzPro755 6.8AF23G00 DA HOLDER VP22 75.8AF28G00 OERLIKON DYNAMIC APERTURE MODULE FOR HD82 85.A526G060 SCREW PAN MECH M2.6*6 Ni NYLOK 80.82G06G00 PCBA PHOTO SENSOR BOARD EP719 HD82/HD8200 Confidential...
  • Page 84 Assy Bottom Case HD82 HD82/HD8200 Confidential...
  • Page 85 Item Description Parts Supply 75.8AF25G00 BUY ASSY BOTTOM BASE MODULE HD82 75.8AF26G003 BUY ASSY IO BASE MODULE HD82 75.8AF24G00 BUY ASSY. BOTTOM CASE MODULE HD82 6.8AF40G00 AC SUPPORT BRACKET SECC 0.6T HD82 6.87F09G00 AC BRACKET SPTE 0.5t EP783 43.8AF0G00 ASSY WIRE AC 490mm HD82 35.8AF0G00...
  • Page 86 Assy LVPS For HD82 HD82/HD8200 Confidential...
  • Page 87 52.87Y03G001 ROD BLOWER RUBBER SLICONE P7270I 6.8AF35G00 LVPS BRACKET SECC 0.6T HD82 5.8AF32G00 LVPS MYLAR HD82 41.89K04G001 EMI GASKET W8*H6*L150 75.8AF0G00 ASSY MATRITEK LVPS FOR HD82 (AC CONNECTOR) 52.85H9G002 THERMAL PAD SARCON GR-d 73.7x24x3.0mm 85.F23G080 SCREW PAN MECH W/SF M3*8 NI GREEN HD82/HD8200...
  • Page 88 Assy Lamp Driver Module For HD82 HD82/HD8200 Confidential...
  • Page 89 Item Description Parts Supply 5.00229G00 SPACER SUPPORT PSW-4S 6.8AF36G00 LAMP DRIVER BRACKET SECC 0.6T HD82 5.8AF33G00 LAMP DRIVER MYLAR HD82 52.83Y11G001 LEDPJ FF1 THERMAL PAD 15*25*3.5t FUJIPOLY SARGON RG-d LEDPJ FF1 70.8AF29GR01 ASSY LAMP DRIVER MODULE FOR HD82(SERVICE) 75.87W01G002 ASSY PHILIPS LAMP DRIVER TopPremium VIDI...
  • Page 90 75.8AF27G00 BUY ASSY FAN BRACKET MODULE HD82 6.8AF45G00 LAMP CNNT BASE AL6063 HD82 85.F23G080 SCREW PAN MECH W/SF M3*8 NI GREEN 42.0043EG003 WIRE 2P 300mm LAMP DRIVER TO LAMP HD82 85.3A522G040 SCREW CAP MECH M2*4-D8 NI 52.83C0G00 RUBBER FAN9225 FLAT EP910 49.82B03G001 KDE1209PTB1 AXIAL FAN R TYPE;”SUNO”...
  • Page 91 Description Parts Supply 52.8850G002 BLOWER DUCT PORON BF-1000 NITTO 5011N 2200MP 6.87340G00 STAND OFF M3*4L D8.0 2100MP 49.87Y02G001 SUNON GB1205PKV1-8AY 50X50X20 OPTICAL EN- GINE BLOWER 52.87306G00 RUBBER BLOWER FAN FRAME 2100MP 6.8AF42G00 BLOWER FAN BRACKET SECC 0.6T HD82 HD82/HD8200 Confidential...
  • Page 92 6.8AF0G00 ENGINE BASE VP22 6.8AF06G00 LENS SHIFT FIRST TRAY VP22 6.8AF05G00 LENS SHIFT SECOND TRAY VP22 6.8AF24G00 LENS SHIFT SPRING VP22 6.8AF54G00 LENSHIFT SPRING PLATE SUS304 0.2t HD82 6.8AF30G00 SHOULDER SCREW M3.0*7 VP22 5.8AF2G00 PLASTIC WASHER NWT-38 PINGOOD 5.8AF4G00 ANTI DUST SPONGE VP22...
  • Page 93 D.P. HD82 HD82 Confidential...
  • Page 94 36.0008G00 EXTENDED WARRANTY REGISTRATION FORM,USA FOR LPP SERIES 36.00020G00 QUICK TROUBLESHOOTING GUIDE MULTILINGUAL 36.8AF04G00 QUICK START CARD MULTILINGUAL OPTOMA HD82 36.0002G002 WARRANTY CARD 3 YEARS, USA FOR OPTOMA LPP SERIES 36.8AF0G00 USER’S GUIDE MULTILINGUAL (CD) OPTOMA HD82 36.8AF03G00 USER’S MANUAL FOR EMEA/USA OPTOMA HD82 42.505G00...

  • Page 95: Serial Number System Definition

    C = Manufacture factory (TW or CPC) 0001 = Serial code EX: Q8AF848AAAAAC0001 This label represents the serial number for HD82. It is produced for USA at CPC on forty- eight week of 2008. Its serial code is 0001. HD82...

  • Page 96: Pcba Code Definition

    PCBA Code Definition PCBA Code for Projector XXXXXXXXXX EEEE Vendor Code Revision Date Code HD82 Confidential...

This manual is also suitable for:

Hd8200

Table of Contents