EC Key EK2 Quick Manual

Turn your phone into a keypad ...
to unlock your car, house, garage door, office, alarm system,
or access control system using.
Walk up with any discoverable Bluetooth phone, you will be
asked for a PIN. Enter the correct PIN and the door will
open.
How do I Install ECKey?
1) You will need a lock or opener, regulated 12 to 24VDC power
supply, flat head screw driver, Philips screw driver, connection
wire and wire cutters.
2) Unscrew the back of ECKey EK2 to identify the connections in
the diagram below.
3) Wire the positive power supply to the Voltage (V+) terminal
and the negative power supply to Ground (G) terminal.
4) Turn the power on and the Status Light should flash four
times and then once every 5 seconds after that.
5) Unplug the power supply.
6) Wire the lock, door opener to ECKey and optionally an
external request to exit button and status light.
7) Plug in the power supply and ECKey is now fully installed.
Fail Secure Wiring
Button
Not Used
Wire/Application Fail Secure
Black (Ground) Ground
(-) Strike
Optional Button
Red (Voltage V+) 12VDC
Yellow (Relay)
(+) Optional Light
Yellow Red (Voltage)
Relay Common
Brown (+) Strike
Normally Open
Blue None
NormallyClosed
Brown Optional Button
Optional Button
Orange (-)Optional Light
Optional Light
Status Light
Administration Button
Normally
Open
Normally
Ground
Closed
Light
Voltage
Fail Safe Request to Exit
Ground Ground
(-) Strike Optional Button
Optional Button
12VDC 12VDC
Yellow (Relay) (+) Optional Light
(+) Optional Light
Red (Voltage) Request to Exit
lock input
None Request to Exit
lock input
(+) Strike None
Optional Button Optional Button
(-) Optional Light (-) Optional Light
EK2 Virtual Keypad
How do I unlock the door?
1) Make phone discoverable (visible) by consulting your phone
documentation (usually in Setting -> Connectivity->
Bluetooth-> Find Me or Setup). We recommend creating a
shortcut to managing Bluetooth on your phone. See your
phone documentation on how to do this.
2) Wait for the phone to be prompted for the PIN. The default
PIN is printed on the label in this user guide.
3) Once the PIN is successfully entered, the relay will trigger and
the Status Light will turn on for 3 seconds to unlock a door,
open a gate or disable an alarm.
Passage mode
In Passage mode ECKey will not monitor phones and the gate or
lock will remain unchanged. To enter Passage mode press and hold
the Administration Button for three seconds until the blue Status
Light comes on. The ECKey relay will remain frozen in its current
state and stop monitoring for phones.
To leave the relay on (for example to leave a strike unlocked)
unlock the door with the PIN on the phone and while the door is
unlocked press and hold the Administration Button for 3 seconds
until the blue Status Light turns off then on again.
To leave the relay off (for example no pulse on an request to exit
button) press and hold the Administration Button for 3 seconds until
the blue Status Light comes on.
To exit Passage mode press and release the Administration Button.
Register for Support
1) You will need an internet connection, ECKey Serial Number,
email address for registration.
2) Go to www.ECKey.com and register with the ECKey Serial
Number printed on your unit in this form EK2-XX-XXXXXXX.
3) Logon into the Support Site and select Knowledge Base->
EK2-Virtual Keypad.
Change the PIN and other settings
1) You will need to be registered for support and have a
Bluetooth device that supports file transfer all Bluetooth PCs
and most phones.
2) Logon into the Support Site and select Knowledge Base->
EK2-Virtual Keypad->Configuration.
3) Select the configuration settings and download the text file on
to your computer.
4) Put ECKey in to Administration Mode by pressing and releasing
the Administration Button three times and press and holding
for three seconds until the Status Light repeatedly flashes
three times.