Advertisement
TOTALINE
THE WIRELESS SENSOR CAN TRANSMIT THE TEMPERATURE IN ONE OF FOUR SELECTABLE TIME INTERVALS:
Every 5 Seconds.
response is needed. Such as: Remote Duct or Room Sensor applications
Every 2 Minutes. This setting is used for Indoor Remote Sensor applications where fast response is
needed. Such as; Remote Duct or Room Sensor applications.
Every 5 Minutes. This setting is also used for Indoor Remote Sensor applications under normal
circumstances. Battery life expectancy is approximately 3 years at this setting.
Every 10 Minutes. This setting is used for Outdoor Temperature reading for use with Residential
Thermostats. Battery life expectancy is at its longest with this setting.
Wireless Sensor Setup & Installation
1
Set the Switches on the Wireless Sensor
4 4
Unit
Unit
2 2
ID
ID
1 1
8 8
House
House
4 4
Code
Code
2 2
1 1
2 2
Tx
Tx
1 1
Interval
Interval
WIRELESS REMOTE SENSOR
Switch Location
2
Attach the Wireless Remote Sensor to the Wall.
Use the supplied screws to secure the Wireless Sensor to the wall.
Care must be taken when installing on to a J-Box to avoid drafts from behind the Sensor.
Troubleshooting & Diagnostics
Use only Lithium AA Batteries. Voltage should be 3.1 - 3.6vdc.
The Receiver's antenna must be fully extended for proper operation.
Make sure the Receiver & Sensor use the same House Code #.
The Receiver has 4 LEDs. The LEDs correspond to Unit ID #0 - 3. When the Receiver receives a valid
temperature from a Wireless Sensor, the corresponding LED will blink and stay on until the next valid
transmission. If a valid transmission is not received within 15 minutes, the LED will turn off.
The Receiver can receive and average up to 8 different Unit ID's on the same House Code, but the LEDs
will only indicate the 1st 4, (#0 - 3). The LEDs are included as a diagnostic tool to confirm reception.
Temperature Range of Wireless Sensor is 32 Fahrenheit to 125 Fahrenheit.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Replacement Components Division - Carrier Corporation - 02/04 - Patents Pending
WIRELESS REMOTE SENSOR
This setting is most useful for Indoor Remote Sensor applications where fast
All Switches in the OFF position = 0.
ADD all switches in the ON position
to arrive at the setting.
The House Code must match the
House Code setting on the Receiver.
A
4 4
Unit
Unit
2 2
Code
Code
1 1
8 8
House
House
4 4
Code
Code
2 2
1 1
2 2
Tx Rate
Tx Rate
1 1
Example A
Unit
ID = 1
House
Code = 3
(1+2 = 3)
Tx
Interval = 5 min.
(2)
P/N 88-140
MODEL
P474-0401-1RF/REC
.
Transmission Interval (Tx Interval)
0 = 5 Seconds
1 = 2 Minutes
2 = 5 Minutes
3 = 10 Minutes
B
Example B
4 4
Unit
Unit
2 2
Unit
Code
Code
1 1
ID = 3
8 8
House
House
(1 + 2 = 3)
4 4
Code
Code
2 2
1 1
House
2 2
Tx Rate
Tx Rate
Code = 1
1 1
Tx
Interval = 5 sec.
(0)
LED's
Jumper
Location
RF Sensor
F
FCC ID: MUHRSTX
FOR HOME OR OFFICE USE
Rev. 2
P474-0401-1RF/REC
C
c
Tested to Comply
with FCC Standards
Advertisement
