D-Link DIR-810L Quick Install Manual

Wireless AC750
Dual Band Cloud Router
DIR-810L
Package Contents
DIR-810L Wireless AC750 Dual Band Cloud Router
Power Adapter
Ethernet Cable
Wi-Fi Configuration Card
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Hardware Overview
2
1
8
3 4 6
5 7
A solid green light indicates a proper connection to the
1 Power LED power supply. The light will be solid orange during boot-up
and will blink green during the WPS process.
A solid light indicates a connection to the Internet port. If
the LED is orange, the connection is good but the router
2 Internet LED cannot connect to the Internet. If this LED is blinking
orange, this indicates that the "on demand" connection
type is set and the Internet connection is idle.
Connect Ethernet devices such as computers, switches,
3 LAN Ports (1-4)
and game consoles.
Connect your broadband modem to this port using an
4 Internet Port
Ethernet cable.
Press and hold the reset button with a paper clip for six
5 Reset Button
seconds to reset the router to the factory default settings.
6 Power Button Press to power the router on and off.
7 Power Port Connect the supplied power adapter.
Press to start the WPS process. The Power LED will start
8 WPS Button
to blink.
Minimum Requirements
Network Requirements:
• An Ethernet-based broadband modem
Web-based Configuration Requirements:
Computer with the following:
• Windows® or Mac OS® X operating system
• An installed Ethernet adapter or wireless adapter
Supported Browsers:
• Internet Explorer 7 or higher
• Safari 4 or higher
• Chrome
• Firefox
Make sure you have the latest version of Java installed. Visit www.java.com
to download the latest version.
mydlink Requirements:
• iPhone/iPad/iPod Touch (iOS 3.0 or higher)
• Android device (1.6 or higher)
• Web Browser Requirements:
• Internet Explorer 7 or higher
• Safari 5 or higher
• Chrome
• Firefox
Note: To learn more about mydlink, visit http://www.mydlink.com.
Before you Start
• Users with DSL providers - If you are using a PPPoE connection, you will need
your PPPoE user name and password. If you do not have this information, contact
your Internet provider. Do not proceed until you have this information.
• Users with Cable providers - Make sure you unplug the power to your modem.
In some cases, you may need to turn it off for up to 5 minutes.
• Advanced Users - If your ISP provided you with a modem/router combo, you will
need to set it to "bridge" mode so the DIR-810L router can work properly. Please
contact your ISP or refer to the user manual for your modem/router device.
Connect your Router
1
Unplug the power to your DSL or Cable modem.
Modem
Connect an Ethernet cable from the Internet port of the router to the
2
Ethernet port on your DSL or Cable modem.
Ethernet Cable
DIR-810L
Ethernet Port
4 3 LAN 2 1 INTERNET POWER 12V 1A
RESET
WPS
T
R
Modem
Internet Port (yellow)
Connect another Ethernet cable from the Ethernet port on your
3
computer to one of the LAN ports on the router.
DIR-810L Computer
Ethernet Cable
4 3 LAN 2 1 INTERNET POWER 12V 1A
RESET
WPS
4
Plug the power back into your DSL or cable modem. Please wait about
one minute before continuing.
Computer
4 3 LAN 2 1 INTERNET POWER 12V 1A
RESET WPS
Modem
DIR-810L
Plug the power adapter into your router and connect to an available
5
power outlet or surge protector. If the Power LED does not light up, press
the Power button on the back of the router.
DIR-810L
Computer
POWER
4 3 LAN 2 1 INTERNET 12V 1A
RESET WPS
Modem
After the router has powered up, verify that the Power (green) and Internet
6
(orange or green) LEDs are both lit then continue with the Configuration
section on the other side.