Advertisement
CW-12 System™
options you can choose from.
F--: Fade Mode Choose desired programs from F01 - F09. The Fade
time of the program can be adjusted from 1% - 99% (0.5 ~50
Sec).
C--: Fixed Color Mode Choose from 20 desired fixed colors from C01
- C20.
001: DMX addressing
Fade Mode:
1. Press the MENU button until the display reads F01. Press the UP
or DOWN buttons until you find your desired fade program.
2. Press and hold the MENU button for at least 3 secs., you can now
adjust the fade speed my pressing the UP and DOWN buttons. The
Fade time of the program can be adjusted from 1 - 99 (0.5 - 50
Sec). 1 being the fastest fade time, and 99 being the slowest.
Press the MENU button to confirm your adjustment.
Fixed Color Mode:
1. Press the MENU button until the display reads C01. Press the UP
or DOWN buttons until you find your desired fixed color.
Universal DMX Control: This mode allows you to use a Elation®
DMX-512 controller to control the CW-12 System™. The CW-12
System™ has two DMX Channel modes, a 3 channel mode and 5
channel mode. Note: When you first use DMX mode, the DCW 4™
will be set to all default modes.
1. To control the CW-12s in DMX mode, follow the set-up procedures
under DCW 4 Control, as well as the set-up procedures included
with your DMX controller. Note: You must confirm you desired
settings before the unit can connect to a DMX signal. You
must confirm settings indivdually. Connect to a DMX signal by
turning your DMX controller "On", and disconnect by turning
the controller "Off"
2. Press the MENU button on the DCW 4 until the LCD screen shows
S--. Use the UP and DOWN buttons to choose your desired DMX
options and DMX channel modes.
S10 - Control all fixtures together (default)
S11 - Control fixture individually
S20 - Master Off (default)
S21 - Master (Master/Slave configuration)
American DJ
- www.americandj.com - CW-12 System™ Instruction Manual Page 9
®
Operation cont.
CW-12 System™
S30 - 3 Channel Mode (default)
S31 - 5 Channel Mode
S40 - Delay Off (default)
S41 - Delay On
Examples of set up procedures:
Example 1: Controlling all fixtures together, is a default setting, so
you do not have to set it. You must decide if you want 3 channel
mode or 5 channel mode, and if you want the delay "On" or "Off".
If you want 5 channel mode, press the UP button until S31 is dis-
played, now press the MENU button so that it goes to address mode.
Select your desired address, and finally connect to DMX. You now
have confirmed you setting. Now disconnect. If you want delay mode
on, press the UP button until the display reads S41. Press the MENU
button so that the addres is displayed, and connect to DMX. You are
now able to control all fixtures together in the 5 channel DMX mode,
with delay mode on.
Example 2: To control fixtures individually in a 3 channel mode. Press
the UP button until S11 is displayed, press the MENU button to go
to address mode, set address, and connect to DMX. Since 3 channel
mode is default you don't have set it.
Example 3: You are set to 5 channel mode and controlling fixtures
individually. Now you want to control all fixtures together in a 3 chan-
nel mode.
Press the UP button so S10 is displayed. Press the MENU button, set
your address, and connect to DMX. Now disconnect DMX, press the
UP button so that S-- is displayed. Press the UP button so that S30
is displayed. Press the MENU button to go to address mode, set the
same address as you did before, and connect to DMX. You should
now be able to control all the fixtures together, in a 3 channel mode.
Note: When you connect to DMX your are saving and confirm-
ing your setting change. You can only save one change at a time,
this is why you have to connect, disconnect, go to your next set-
ting and connect again.
NOTE: If you do not follow these procedures, DMX control will
not work.
3. See page11 for detailed description of the DMX traits. Use your
DMX controller to activate the programs and chases.
American DJ
- www.americandj.com - CW-12 System™ Instruction Manual Page 10
®
Operation cont.
Advertisement
