Advertisement
VEC270SB_Manual_062105.qxd
6/23/05
Typical Inflation Times
Inflation pressure (psi)
Vehicle and trailer tires
155/80R 13"
185/70R 14"
235/75R 16"
235/70R 17"
Bicycle tires
27" X 1" (racing)
Sports Equipment
Football
Basketball
Volleyball
WARNING
Always follow manufacturer's recommendations for pressure on item
to be inflated.
CARE AND MAINTENANCE
Replacement Parts
Contact Vector's Technical Support Department toll free at (866) 584-5504 or visit our
website (www.vectormfg.com) for replacement parts (including replacement adapters
and cords) and any additional information that you may need.
WARNING
To reduce the risk of shocks or burns and avoid damage to the unit,
make sure all power switches are in the OFF position, all adapters are
unplugged and the unit has been allowed to cool down before
performing any maintenance/parts replacement.
Bulb Replacement
The quartz halogen bulb assembly is available through Vector (see contact
information above). A comparable (12 volt H3 25 watt) bulb may be substituted.
These can also be purchased from popular automotive parts suppliers nationwide.
You will need a Phillips screwdriver to replace the bulb.
HAIRPIN RETAINING
WIRES
1. Remove the rubber bezel from the lens cover.
2. Unscrew (counterclockwise) and remove the two Phillips screws located on either
side of the lens.
3. Carefully separate the lens guard, lens glass and rubber gasket from the reflector.
5:24 PM
Page 6
Approx. Filling time
26
2.5 min.
30
4.5 min.
30
6.5 min.
42
16 min.
70
2.3 min.
13
24 sec.
10
20 sec.
5
6 sec.
Open
Closed
SCREW
6
4. Gently lift the reflector and bulb assembly from the housing; note that the wires
are still attached to assembly.
5. Unsnap the retaining wire from the reflector's flange by pinching the two ends
together and lifting.
6. Loosen the Phillips-head retaining screw (no need to completely remove) to free
the bulb assembly from the reflector.
7. Slightly turn and lift out the bulb assembly from the back of the reflector.
8. Disconnect the bulb assembly's white wire from the red power wire by separating
the male spade terminal from the female terminal.
9. Insert the replacement bulb assembly into the reflector flange.
10. Reverse the proceeding procedure to reassemble the Spotlight.
11. Press the Spotlight's Power Pushbutton ON to test proper operation of spotlight.
Battery Replacement/Disposal
It is recommended that the unit be returned to Vector Customer Service for battery
replacement.
Contains a maintenance-free, sealed, non-spillable, lead acid battery,
which must be disposed of properly. Recycling is required, contact your
local authority for information. Failure to comply with local, state and
federal regulations can result in fines, or imprisonment. For more
information on recycling this battery, call toll-free (877) 288-7722.
Fuse Replacement
The VEC270SB contains a 15 amp blade fuse located in the Inflator Hose/
Accessory Storage Compartment. You will need small needle nose pliers to replace
the fuse.
1. Open the Inflator Hose/Accessory Storage Compartment cover.
2. Grasp the blade fuse with the needle-nose pliers and pull straight out.
3. Replace the fuse with the same size and type.
SPECIFICATIONS
Battery Type(s):
Sealed, high density, AGM, lead-acid, rechargeable,
maintenance-free, 6 volt DC, 4.5 Amp-hour
Spotlight:
H3 25 watt bulb
Accessory Outlet:
Protected by a 15 Amp Fuse
DC Charger/Adapter:
12 volt DC/DC
AC Charger/Adapter:
120 volt AC (500mA 12 volt DC Output)
7
Advertisement
