Optoma EP1080 Service Manual
  1. Manuals
  2. Brands
  3. Optoma Manuals
  4. Projector
  5. EP1080
  6. Service manual

Optoma EP1080 Service Manual

Projection system
Hide thumbs Also See for EP1080:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL

EP1080/DX1080/OP1990/VE810/DP7290/
Date
2008.09.10
2008.09.22
2009.03.13
Copyright March, 2009. All Rights Reserved P/N:36.8BH03G001
SI :
PV8530/P350/TX1080
Revise Version
V1.0
V2.0
V3.0
TSE:
Modify Chapter 1 and add Chapter 7
Add EP1080 extended models: DX1080, OP1990,
VE810, DP7290, PV8530, P350, TX1080 and amend
the method of getting into FW mode in Chapter 5
Check:
Description
Initial Issue
Approved:

Advertisement

Table of Contents
loading

Related Manuals for Optoma EP1080

Summary of Contents for Optoma EP1080

  • Page 1: Service Manual

    V1.0 Initial Issue 2008.09.22 V2.0 Modify Chapter 1 and add Chapter 7 Add EP1080 extended models: DX1080, OP1990, 2009.03.13 V3.0 VE810, DP7290, PV8530, P350, TX1080 and amend the method of getting into FW mode in Chapter 5 Copyright March, 2009. All Rights Reserved P/N:36.8BH03G001...
  • Page 2 Preface This manual is applied to EP1080 Series projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products.

  • Page 3: Table Of Contents

    Disassemble Engine Module 2-13 Disassemble Color Wheel Module 2-14 Disassemble DMD Chip 2-15 Disassemble LVPS Module 2-15 Disassemble Ballast Module 2-16 Disassemble Blower Module 2-17 Disassemble Safety Switch 2-18 Disassemble IR Sensor Board and AIR Duct 2-18 EP1080 Series Confidential...
  • Page 4 Service Mode OSD Reset Test Condition Test Inspection Procedure PC MODE Calibration Optical Performance Measure 4-10 Video Performance 4-12 Network Function Test 4-14 Others 4-16 Chapter 5 Firmware Upgrade Equipment Needed USB Driver Setup Procedure Firmware Upgrade Procedure EP1080 Series Confidential...
  • Page 5 EDID Key-In Procedure(VGA-2 & DVI-D Interface) Setup Procedure(VGA-1 & HDMI Port) EDID Key-In Procedure(VGA-1 & HDMI Interface) Chapter 7 Network FW Upgrade Equipment Needed Read Projector IP Network Setting PC Hardware Link Appendix A Exploded Image Appendix B Serial Number System Definition PCBA Code Definition XX EP1080 Series Confidential...

  • Page 6: Chapter 1 Introduction

    Color wheel 5 Segment, RYGWB (R80Y40G82W78B80) • System controller Dual DDP3021, DAD1000, PMD1000 for 1080p DMD • Lamp Philips 300Watt E21.9 UHP • Operating 0~2,500 ft 5°C~35°C 2,500~5,000 ft 5°C~30°C Altitude 5,000~10,000 ft 5°C~25°C • Storage 40,000 ft EP1080 Series Confidential...
  • Page 7 RCA(L/R) x 1 for S-video, Composite • Advanced air flow • One fan/ two blowers(in projector) with low system acoustic noise level Cooling System • Temperature control circuits with adaptive voltage control fan speed • Max touch temperature follows UL60950 regulation EP1080 Series Confidential...
  • Page 8 Audio-in (3.5mm) x 3 for VGA1, VGA2, DVI-D • Audio-out (3.5mm) x 1 • Audio-in RCA(L/R) x 1 for S-video, Composite • One D-sub 9-pin RS-232 port • USB x 1 (Type B) • RJ-45 x 1 • One 3-pin AC power inlet port EP1080 Series Confidential...

  • Page 9: Compatible Mode

    1-2 Compatible Mode Analog Compatibility Resolution V-Sync [Hz] 640x350 640x350 640x400 640x480 640x480 640x480 640x480 720x400 720x400 800x600 800x600 800x600 SVGA 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1280x720 WXGA* 1280x768 1280x768 1280x1024 SXGA 1280x1024 SXGA+ 1400x1050 UXGA 1600x1200 EP1080 Series Confidential...
  • Page 10 Digital Compatibility Resolution V-Sync [Hz] 640x480 640x480 640x480 640x480 800x600 SVGA 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1280x768 WXGA 1280x768 1280x720 1280x1024 1280x1024 SXGA+ 1400x1050 UXGA 1600x1200 Confidential EP1080 Series...

  • Page 11: Disassembly Process

    * Before you start: This process is protective level II. Operators should wear electrostatic chains. * Note: - If you need to replace the scaler board, you have to record the lamp usage hour. - As the process of EP1080 extended models disassembling is the same as EP1080, we take EP1080 for example here.

  • Page 12: Disassemble Lamp Cover Module

    Cover Module 1. Unscrew 2 screws (as red circle) on the Lamp Cover. 2. Disassemble Lamp Cover Module. 2-3 Disassemble Lamp Module 1. Unscrew 2 screws (as red circle) on the Lamp Module. 2. Take off Lamp Module. EP1080 Series Confidential...

  • Page 13: Disassemble Lens Shelter

    Cover (as red circle). 2. Unscrew 2 screws from the Rear Cover (as yellow circle). 3. Push forward to remove the Top Cover Module. 4. Unplug 1 FPC Cable from the Scaler Board Module (as blue circle). EP1080 Series Confidential...

  • Page 14: Disassemble Keypad Board Module

    1. Unplug 1 FPC cable (as red circle). 2. Take off EMI Gasket (as green square), EMI Type (as red square) and Keypad Type (as yellow square). 3. Unscrew 5 screws (as yellow circle). 4. Disassemble the Keypad Board Module. EP1080 Series Confidential...

  • Page 15: Disassemble Vent

    2-7 Disassemble Vent 1. Unscrew 1 screw on the Left Vent (as red circle). 2. Turn the projector to backside and unscrew 3 screws (as blue circle). 3. Uplug 1 connector (as yellow square) and remove the Left Vent. EP1080 Series Confidential...
  • Page 16 4. Unplug 4 clips (as red sqaure) and remove the Speaker. 5. Unscrew 2 screws on the Right Vent (as green circle). 6. Turn the projector backside and unscrew 3 screws (as orange circle). 7. Remove the Right Vent. EP1080 Series Confidential...

  • Page 17: Disassemble Rear Cover Module

    3 usual screws (as yellow circle). 2. Turn the projector backside and unscrew 3 screws (as green circle). 3. Unplug the connector (as orange sqaure) and remove the Rear Cover. 4. Unplug 4 clips (as red sqaure). EP1080 Series Confidential...

  • Page 18: Disassemble Formatter Board And Scaler Board Module

    1. Take off mylar (as red square). 2. Unplug 10 connectors (as yellow square). 3. Unscrew 7 screws (as green circle). 4. Remove the Formatter Board and Scaler Board Module. Note:The formatter board is connected on the DMD board (as yellow square). EP1080 Series Confidential...
  • Page 19 5. Unplug 3 connectors (as blue square) to seperate two boards. 6. Take off Lan Board from the Formatter Board. 7. Take off 3 Hex screws (as green circle) from the Scaler Board. EP1080 Series Confidential...

  • Page 20: Disassemble Air Ductor

    1. Tear off 1 tape kapton (as red square). 2. Unscrew 1 screw (as green circle), then disassemble Air Duct. 2-11 Disassemble System Fan Module 1. Unscrew 2 screws (as red circle) and disassemble Fan Module. EP1080 Series Confidential 2-10...
  • Page 21 2. Unscrew 4 screws (as yellow circle) and separate Bracket and Fan. 3. Unscrew 2 screws (as green circle), separate thermal switch and ground wire and others. EP1080 Series Confidential 2-11...

  • Page 22: Disassemble Left Shielding Module

    3 screws (as green circle) and separate Fan and Left Shielding , then tear off mylar (as blue square) from the Left Shielding. Note: - Take the Fan Module as the right gesture. the wrong gesture the right gesture EP1080 Series Confidential 2-12...

  • Page 23: Disassemble Engine Module

    1. Disassemble 1 mylar (as orange square) and EMI Gasket (as blue square). 2 .Unscrew 6 screws (as red circle) to disassemble Engine Module. 3. Turn the Focus Ring as the yellow as the yellow direction,then disassemble Focus Ring. disassemble Focus Ring. EP1080 Series Confidential 2-1...

  • Page 24: Disassemble Color Wheel Module

    1. Unscrew 2 screws (as red circle) to disassemble Color Wheel Module. 2. Unscrew 1 screw (as yellow circle) to disassemble Photo Sensor Board from Color Wheel Module. Note: - Avoid to touch the glass parts of color wheel. EP1080 Series Confidential 2-1...

  • Page 25: Disassemble Dmd Chip

    - To double check and see if the pin is out of shape. 2-16 Disassemble LVPS Module 1.Unscrew 6 screws (as red circle). 2. Disassemble LVPS Module holder, mylar, Disassemble LVPS Module holder, mylar, AC Inlet Bracket. EP1080 Series Confidential 2-15...

  • Page 26: Disassemble Ballast Module

    4. Unplug 1 connector (as yellow square) (as yellow square) and separate LVPS and the wire . and separate LVPS and the wire . 2-17 Disassemble Ballast Module 1. Unsrew 5 srews (as red circle),and disassemble Ballast Module. EP1080 Series Confidential 2-1...

  • Page 27: Disassemble Blower Module

    2. Unplug 3 connectors (as orange square) and all wires,then dissassemble Ballast Module. 2-18 Disassemble Blower Module 1. Unscrew 2 screws (as red circle). 2. Remove the Blower Module and separate Blower and Rubber. EP1080 Series Confidential 2-17...

  • Page 28: Disassemble Safety Switch

    1.Unscrew 3 screws (as red cirle). 2. Disassemble Safety Switch. 2-20 Disassemble IR Sensor Board and AIR Duct 1. Tear off 1 mylar (as yellow square) and EMI Gasket (as green square). 2. Take off IR Sensor Board. EP1080 Series Confidential 2-18...

  • Page 29: Disassemble Left And Right Elevator Module

    3. Unscrew 2 screws (as red circle). 4. Take off AIR Duct. 2-21 Disassemble Left and Right Elevator Module 1. Unscrew 3 screws on the Left Elevator Module (as red circle). EP1080 Series Confidential 2-1...
  • Page 30 3. When pressing the push button,the elevator foot will get loose and be easily to be pulled down to separate the Elevator Module. 4. The methed of disassembling the Right Elevator Module is the same as the Left Elevator Module. EP1080 Series Confidential 2-20...

  • Page 31: Rod Adjustment

    - It should not have any abnormal color at the rim of the image by estimating through the eyes. Note: - To avoid over adjusting the rod. - After the opreation, please use the glue to fix the screws. EP1080 Series Confidential 2-21...

  • Page 32: Re-Write Lamp Usage Hour

    Mode Hours increase/decrease 2 hours, the lamp Hour will increase/decrease 1 hour. 5. Chose "Exit". Note: left key = decrease Bright Mode Hours/ Standard Mode Hours, right key = increase Bright Mode Hours/ Standard Mode Hours. EP1080 Series Confidential 2-22...

  • Page 33: Chapter 3 Troubleshooting

    (Blue) (Blue) Flashing Flashing Power off (Cooling) Flashing (Blue) (Blue) Error (Lamp failed) (Red) Error (Thermal failed) (Red) Error Flashing (Over Temp.) (Red) Error Flashing (Fan failed) (Red) Error RS232 fail Flashing Light on Light off EP1080 Series Confidential...

  • Page 34: Main Procedure

    Temp LED Lights red or Flashing red Auto Shut Down - Check Thermal Switch - Check Fan c. Lamp LED Lights red - Check Lamp - Check Lamp Driver - Check Formatter Board - Check Photo Sensor EP1080 Series Confidential...
  • Page 35 - Check Color Wheel Mechanical Noise - Check Fan Module - Check if the Formatter Board and the DMD Board are assembled properly - Check Scaler Board Line Bar/Line Defect - Check DMD Board - Check DMD Chip EP1080 Series Confidential...
  • Page 36 - Clean DMD Chip and Engine Module (Out of spec.) - Check DMD Chip - Check Engine Module - Ensure that the signal cables and source work as well. - Check Scaler Board Garbage Image - Check Formatter Board - Check DMD Board EP1080 Series Confidential...
  • Page 37 Internet transmission speed over 100MB/second, Green LED will light.) Network Function Abnormal - Check Internet Source and Network Module if LED message is in abnormal status. - Check Formatter Board if LED message is in normal status. EP1080 Series Confidential...
  • Page 38 Universal Password will enable you start the projector up and reset the password. - The EP1080 series’s Universal Password is 2468. - Universal Password is the password of Administrator. It can be accepted by projector anytime no matter what the projector’s password is.
  • Page 39 - The message “Enter New Security Code” appears. Input a 4-digits code (letters and/or numbers) that you define. Forgetting Password (administrator Password) - To confirm, enter the password again. The “Security Code change successfully” appear on the screen. EP1080 Series Confidential...

  • Page 40: Function Test & Alignment Procedure

    1. After final QC step, we have to erase all saved change again and resotre the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting: (1) Please get into OSD menu. (2) To execute "Reset" function. EP1080 Series Confidential...

  • Page 41: Test Condition

    Set burn in cycle Press right key to adjust the cycle After setting up the time, choose Burn-In mode and hit enter Screen Defects (While replacing DMD Chip, DMD BD and Scaler BD) < Figure: Zone A &B Definition > EP1080 Confidential...

  • Page 42: Test Inspection Procedure

    (2) Select "Tracking" function and use right or left arrow key to adjust the value to minimize video flicker. - Adjust Resync or Frequency/Tracking/H. Position/V. Position to the inner screen. Master EP1080 Series Confidential...
  • Page 43 - Test Pattern: blue 60 Inspection item - Dark blemish check. (dirty) Criteria - The bright blemish is unacceptable when it appears on blue 60 pattern. Blue 60 - Ref. the Defect specification table Note: The defect criteria follows TI specification. EP1080 Series Confidential...
  • Page 44 Full screen crisp, and sharp over the entire surface of the display pattern. (Blur word on one of the corner after adjustment is acceptable. However, the word should at least be recognizable.) MEME Sony EP1080 Series Confidential...

  • Page 45: Calibration

    4-7 Calibration 1. Video calibration Procedure - Test equipment: video generator. - Once scalar board is changed, Video calibration should be done as well. (1) Test signal: 720P EP1080 Series Confidential...
  • Page 46 (1) Test signal analog: 800x600@60Hz (2) Test Pattern: gray 16 (800x600@60Hz) - Note (1) Calibration pattern should be in fill screen mode. Gray 16 (2) Please refer to 4-2 to get into Service Mode and OSD Reset. EP1080 Series Confidential...

  • Page 47: Defect Specification Table

    Unstable pixel (dots) Any pattern A+B=1 Adjacent dark pixel (dots) Any pattern A+B=0 A+B=2 Dark blemish (Dirty) Blue 60 pattern (diameter <1/2 inch) A+B=2 Bright blemish (Dirty) Gray 10 pattern (diameter <1/2 inch) Bright dot on frame Black pattern EP1080 Series Confidential...

  • Page 48: Optical Performance Measure

    - Use CL100 to measure brightness values of full white pattern P5 & full black pattern B5 ( see im- age: full white) - Follow Contrast formula to calculate contrast values. ☼ Contrast Formula Full black pattern P5/B5 Note: P5=center of white image EP1080 Series Confidential...

  • Page 49: Video Performance

    - Test equipment: DVD player - Test signal: S-Video Inspection item - Video performance test Inspection Distance - 1.8 M ~2.5 M Criteria - Check any abnormal color, line distortion or any noise on the screen. EP1080 Series Confidential 4-10...
  • Page 50 - Test equipment: DVD player - Test signal: CVBS Inspection item - Audio performance test Inspection Distance - 1.8 M ~2.5 M Criteria - Check the sound from speakers - Check “Volume” is normal - Check “Mute” is normal EP1080 Series Confidential 4-11...

  • Page 51: Network Function Test

    “RS232”, then press “Enter”, select “Network”, press “Enter”. - Use down button to remove the light mark to “Network” then press “Enter”, the picture will show on screen, then write down the IP address: 192.168.0.100. EP1080 Series Confidential 4-14...
  • Page 52 - Modify the IP address to 192.168.0.101, and modify Subnet mask to 255.255.255.0. Note: The HOST ID (192.168.0.XXX) of PC IP address must be different from the projector IP address written down in step 1. - Click “OK”. EP1080 Series Confidential 4-15...

  • Page 53: Others

    - All preset modes shall expand to full screen size using OSD Horizontal and Vertical Size controls Display Data Channel (DDC) - The purpose of the DDC test is to verify the DDC1/ DDC2B operation of the projector and to verify Plug & Play function. EP1080 Series Confidential 4-16...
  • Page 54 Focus Ring Focus ring is functioning smoothly. Logo missing logo, missing prints and blurry prints are unacceptable Screw All screws should be fixed and in right type. Elevator is well-functioned. Elevator Stuck key is unacceptable. Pedestal well-functioned EP1080 Series Confidential 4-17...

  • Page 55: Firmware Upgrade

    Chapter 5 Firmware Upgrade 5-1 Equipment Needed Software: (DDP 3021) - Appcode.inf - FlashUpgrader.exe - USB Driver Hardware: - Projector - Power Cord (P/N 42.50115G001) - USB Cable:42.00280G001 - PC EP1080 Series Confidential...

  • Page 56: Usb Driver Setup Procedure

    (4) Select "Include this location in the search", then click "Browse". (5) "Browse For Folder" will be appear on the screen. (6) Select "UsbDriver", then click "OK". Note: - Windows Find New hardware Wizard will show, just wait a moment. EP1080 Series Confidential...

  • Page 57: Firmware Upgrade Procedure

    3. Click "Choose" and select "appcode.inf" , then click "open". 4. Process - Select the USB port which is connected with the fixture, baud rate should be 115200. - Click "Flash". 5. Firmware upgrade process will take about 2 minutes. EP1080 Series Confidential...
  • Page 58 Power LED will light off, the Power LED will light on and appear red, then close FlashUpgrader program and unplug Power Cord to finish firmware upgrade. 7. Then get into the service mode 1 to check the firmware version. EP1080 Series Confidential...

  • Page 59: Edid Upgrade

    Note: - If a display device has digital input ports, like DVI or HDMI, but without EDID in its scaler board, the display device will show no image while the input source is digital signal. - The EDID upgrade procedure for EP1080 Series is the same. Here, we take EP1080 as an example.

  • Page 60: Equipment Needed

    6-2 Equipment Needed Software - EDID Program (Generic V0.51) - EDID File (Optoma-EP1080 EDID-B01.ini) Hardware - Projector - Generic Fixture :80.00001.001 for EDID Key-in (Fixture: JP3 must be closed) - Power cord - RS-232 Cable (pin to pin, F-M): 42.83618G001...

  • Page 61: Setup Procedure(Vga-2 & Dvi-D Port)

    - In the port selection bar, please choose the port that you use. Example: if you use "COM2," choose COM2 in the port selection. - Click on "Model". - Choose the the source file (*.ini) "OPTOMA_EP1080_EDID_B01.ini" and open it. EP1080 Series Confidential...
  • Page 62 5. Change the cable to Digital - When the message "Please change the cable to Digital" is shown on the screen, click "OK" button. 6. When the EDID program is completed, a message "OK" will appear on the screen. EP1080 Series Confidential...
  • Page 63 - In the Read item, select "Analog" and "Trans", then click the "Read" button. 8. Read EDID "Digital" information - If EDID’s information is correct,select "Digital" and "Trans" in the Read item, then click the "Read" button. - EDID informations will show the result. EP1080 Series Confidential...

  • Page 64: Setup Procedure(Vga-1 & Hdmi Port)

    - When the message "Please change the cable to Analog" is shown on the screen, click "OK" button. 3. Change the cable to Digital - When the message "Please change the cable to Digital" is shown on the screen, click "OK" button. EP1080 Series Confidential...
  • Page 65 - In the Read item,select "Analog" and "Trans",then click the "Read" button. 6. Read EDID "Digital" information - If EDID’s information is correct,select "Digital" and "Trans" in the Read item,then click the "Read" button. - EDID informations will show the result. EP1080 Series Confidential...

  • Page 66: Equipment Needed

    Software : - EP1080_Tfufls_A05.bin (*.bin) Hardware : - Projector - Power Cord - LAN Cable - PC Note: - The Network FW Upgrade Procedure for EP1080 Series is the same, here we take EP1080 as an example. EP1080 Sereis Confidential...

  • Page 67: Read Projector Ip

    "Enter" button, select "Network", press "Enter" button again. 2. Select "Network", press "Enter" button. 3. Remove the light mark to "DHCP", then press "Enter" button, select "ON", press "Enter" button, the IP address will be shown on screen. EP1080 Series Confidential...

  • Page 68: Network Setting

    Subnet mask to 255.255.255.0. Note: - The HOST ID (192.168.0.XXX) of PC IP address must be different from the projector IP address written down in step 3 of 7-2. 4. Click "OK". 5. Click "Close" to quit the setting screen. EP1080 Series Confidential...

  • Page 69: Pc Hardware Link

    7-4 PC Hardware Link 1. Connect PC with the Projector by LAN Cable. 2. Execute "Internet Explorer". 3. Key-in IP Address "http:// 192.168.0.100/tgi/ fu.tgi" to get into Firmware Update screen,and then click "Continue". EP1080 Series Confidential...
  • Page 70 - Click "Browse" button to select the FW file (*.bin) which you saved. - Click "Update" to start update. 5. Firmware Update procedure. 6. Click "Re Login". 7. Firmware upgrade procedure completes. - The Projector Network FW version will appear. EP1080 Series Confidential...
  • Page 71 Appendix A D.C. EP1080 EP1080 Series Confidential...
  • Page 72 AC NLET SHELDN EP1080 75.8BH10G001 LENS CAP MODULE EP1080 49.83C03G001 SUNON 50*10 AXAL FAN/GM1205PF 70.8BH30GR01 ASSY ELEVATOR FOOT MODULE(SERVCE) 70.87T05G001 ASSY ELEVATOR FOOT RGHT MODUL 49.82B01G001 MSC BLOWER GB1206PTV2-AY R TYPE ASSY LAMP DRVER WAVEFORM FOR EP1080 70.8BH29GR01 (SERVCE) EP1080 Series Confidential...
  • Page 73 Assy LVPS Module EP1080 item Description Parts Supply 75.83C13G001 BUY ASSY NTER LOCK SWTCH ACR 75.85H15G001 ASSY LVPS MATRTEK 300W(HD81) EP1080 Series Confidential...
  • Page 74 Assy PCBA Scaler/B+Formatter/B Module EP1080 item Description Parts Supply 80.8BH01G002 PCBA SCALER BOARD FOR EP1080 80.8BH06G002 PCBA FORMATTER BOARD FOR EP1080 70.8BH25GR01 ASSY PCBA LAN MODULE EP1080(SERVCE) 70.8BH23G001 ASSY PCBA LAN MODULE EP1080 EP1080 Series Confidential...
  • Page 75 Assy LAMP COVER Module item Description Parts Supply 70.87T16GR01 ASSY LAMP COVER MODULE HD81-LV(RMA) 41.82G12G002 EMI GASKET W10*L20*H2.5mm 51.83C06G021 LAMP COVER BLACK HD81-LV 61.83C20G001 AL SHIELDING 0.1t FOR LAMP COVER EP1080 Series Confidential...
  • Page 76 Assy LAMP DRIVER Module item Description Parts Supply ASSY LAMP DRVER WAVEFORM FOR EP1080 70.8BH29GR01 (SERVCE) 75.8AY02G001 ASSY LAMPDRVER PHLPS 300W EP1080 Series Confidential...
  • Page 77 Assy LEFT COVER EP1080 item Description Parts Supply 75.8BH08G001 BUY ASSY LEFT COVER EP1080 49.83C01G201 SPEAKER 2W4OHM L100mm REAR COVER EP1080 Series Confidential...
  • Page 78 Assy Optical Engine Module EP1080 EP1080 Series Confidential V...
  • Page 79 DMD HEATSNK EP1080 61.85H14G001 DMD MASK HD81 61.85H34G001 DMD-PCB PRESSCOVER HD81 61.82B36G001 SCREW M3*10 HSPC ‘’ 61.8BH06G001 HEATSNK SPRNG EP1080 70.8BH18G001 BUY ASSY OPTCAL MODULE EP1080 80.87C02G011 PCBA DMD BD1 ENTEK FOR HD80 41.81U02G001 EMI TAPE W40*L40mm EP1080 Series Confidential...
  • Page 80 Assy Engine Base EP1080 EP1080 Series Confidential...
  • Page 81 Description Parts Supply 70.8BH26GR01 ASSY OPTCAL ENGNE MODULE EP1080(SERVCE) MODULE EP1080(SERVCE) 85.1A123G060 SCREW PAN MECH M3*6 N 23.83C10G001 Kinko UV_IR AR FOR EP910 25.7*25.7*2.75mm 51.82B46G001 ENGINE MASK MYLAR FRPP 0.43t 5100MP ‘’ 52.82B02G001 OFF LGHT SOLATOR RUBBER 5100MP ARTGHT PORON FOR ENGNE-BLOWER FAN 52.82B17G001...
  • Page 82 Assy Top Cover Module EP1080 EP1080 Series Confidential...
  • Page 83 41.83C20G001 EM TAPE W78MM*L128MM 41.83C21G001 EM GASKET W13*H5*L50MM FFC KEYPAD TO FORMATTER BD 16P P=0.5 42.00304G001 122mm HD80 52.85H04G002 TOP COVER SPONGE 60mm HD81 52.83C04G001 LGHTCUT SPONGE FOR FR-R EP910 75.87T03G011 BUY ASSY TOP COVER EP1080 EP1080 Series Confidential X...
  • Page 84 Assy Keypad Module EP1080 item Description Parts Supply 51.83C18G031 KEY PAD BUTTON (BLACK) EP1080 51.83C19G001 LED TRANSPARENT BAR EP910 61.83C09G001 KEYPAD BRACKET SECC 1.0t EP910 80.87Z03G001 PCBA KEYPAD BOARD FOR HD80 85.1A123G060 SCREW PAN MECH M3*6 N 85.1D122G050 SCREW PAN MECH M2*5 Ni (W/WASHER φ5.0)
  • Page 85 Assy Fan Module EP1080 item Description Parts Supply 61.83C04G002 BRACKET FAN9225 HOLDER AL EP91 52.83C01G001 RUBBER FAN9225 FLAT EP910 49.83C04G001 SUNON 9225 AXAL FAN/KDE1209PT 61.89552G001 FAN9225 PLATE AL 4100MP 43.83C17G001 THERMAL SWTCH/YS11A105B-026 85.1A123G060 SCREW PAN MECH M3*6 N 52.82B15G001 FAN 9225 RUBBER TOP 5100MP 61.89547G001...
  • Page 86 D.P. EP1080 item Description Parts Supply DC.8BH01G001 D.C. EP1080 75.8BH10G001 LENS CAP MODULE EP1080 35.89603G001 LABEL SPEC EP759 57.00001G001 PACK SO2 DRER 20g 56.83C03G002 PACKNG EPE PAPER #535*450*0.8 EP910 35.83C03G001 LAMP WARNNG LABEL EP910 56.83C04G001 CUSHON RGHT EPE EP910 56.83C05G011 CUSHON LEFT EPE HD80 55.83C04G021...
  • Page 87 A.K. EP1080 2-10 EP1080 Series Confidential XV...
  • Page 88 Description Parts Supply 55.83C02G001 ACCESSORY BOX EP910 QUCK START CARD MULTLNGUAL OPTOMA 36.8BH02G001 EP1080 36.00020G001 QUCK TROUBLESHOOTNG GUDE MULTLNGUAL 35.82001G111 AK LABEL 3”*3” BLANK 45.8BH01G001 NFRARED REMOTE CONTROL EP1080 42.00281G101 CABLE USB-A TO USB-B 1.8M BLACK EXTENDED WARRANTY REGSTRATON FORM, 36.00018G001...

  • Page 89: Serial Number System Definition

    C = Manufacture factory (TW or CPC) 0001 = Serial code EX: Q8BH831AAAAAC0001 This label represents the serial number for EP1080. It is produced for USA at CPC on thirty-one week of 2008. Its serial code is 0001. EP1080 Series...

  • Page 90: Pcba Code Definition

    II. PCBA Code Definition PCBA Code for Projector XXXXXXXXXX EEEE Vendor Code Revision Date Code EP1080 Series Confidential...

This manual is also suitable for:

Dx1080Op1990Ve810Pv8530P350Tx1080 ... Show all

Table of Contents