IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL INSTRUCTIONS Warning — Risk of injury: Children, the elderly, DANGER — RISK OF ELECTRICAL SHOCK: When and the infirm should not use the spa unless they are installing and operating this electrical equipment, basic supervised at all times.
INSTALLATION Inspection and Shipping Claim Check for shipping damage upon receipt of the spa. Jacuzzi Whirlpool Bath is not responsible for damage to the spa sustained during shipment. If damage is evident before unpacking, refer to instructions regarding shipping claims on the outside of the carton and immediately file a claim with the carrier.
Bonding lugs are available at help maintain comfort and minimize moisture damage your local electrical supply store. (Bond bar location is to the building. Jacuzzi Whirlpool Bath is not respon- shown below.) sible for damages resulting from excess moisture or water spillage.
6. Clean the interior of the spa of any remaining con- All Jacuzzi Whirlpool Bath spas are factory tested for struction debris. Remove stubborn stains, paint, or proper operation and water tight connections prior to tar with turpentine, isopropyl alcohol or paint thinner.
Besides being a beautiful addition to your indoor decor or outdoor landscaping, your Jacuzzi Whirlpool Bath spa will provide you with the ultimate in spa pleasure. Familiarize yourself with the operation of the electronic control panel, as described on pages 6-8 of this manual.
OPERATION Control Panel The control panel is easy to use with fingertip control of all the spa's functions. Control of temperature, jets, blower, filtration and spa light is readily accessible at your fingertips. PROGRAM LIQUID CRYSTAL WARM TIME LIGHT DISPLAY FILTER 1 STANDARD HEAT...
OPERATION Control Panel Operation Initial Start-Up The spa will automatically begin to operate when elec- Press . Time of day will be shown. Then press trical power is applied. There is no ON/OFF switch for the spa system. The control system is designed so that by simply con- .
OPERATION Temperature Lock Press . The display will read The temperature lock is provided to prevent unautho- rized temperature adjustment of your spa. While setting your spa water temperature, and after you have pressed Then . The display will read , follow the instructions below to lock the set temperature.
OPERATION Normal Operation/Whirlpool Air Blower System The spa features a built-in air blower and air jets in the seats of the spa to add to your enjoyment. You can enjoy the spa with or without activating the The blower sends air to air injectors located in the whirlpool.
OPERATION Six-Jet Wave Seat A separate knob located on the inside of the spa rim controls this function. Rotate to increase the cycle rate and rotate in the opposite direction to decrease the rate. CONTROL KNOB FOR WAVE SEAT JETS...
You can ensure better water chemistry by testing your spa water every day and adjusting the chemical balance frequently. Obtain a water quality test kit, designed especially for spas, from your Jacuzzi Whirlpool Bath dealer. The test kit must be of the type which allows you to test for the disinfectant (chlorine) level, pH, and total alkalinity. Ensure that the chemicals used in your spa are especially for spa use, and not for swimming pools, as water quality maintenance of spas and of swimming pools is very different.
MAINTENANCE Water Chemistry (Continued) Disinfecting Balancing pH When filling the spa for the first time, follow the For good hygiene and equipment longevity, main- purge/sanitizing instructions in the Equipment Set-Up tain the pH of your spa water according to the instruc- procedure of the Installation Instructions.
CAUTION: Ensure replacement of the suction cover (available from your Jacuzzi Whirlpool Bath dealer or immediately after cleaning. It is a safety device and most pool supply stores). Follow the manufacturer’s must be in place over the suction fitting to minimize instructions for use.
MAINTENANCE Cycle Valve Strainer If there is a decreased water flow from the six-jet wave seat, the cycle valve strainer should be cleaned. REMOVE THIS PANEL The spa must be drained before accessing the strainer. TO ACCESS STRAINER To access the strainer, remove all the screws securing the skirt panel indicated.
An optional spa cover for your spa is available from stalled when service has been completed. your Jacuzzi Whirlpool Bath dealer. Use of this cover will help to reduce energy costs by minimizing heat loss and Spa Light evaporation.
E. GFCI tripped. E. Reset GFCI. F. Faulty pump or motor. F. * *NOTE: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath dealer.
Page 19
10. Low water flow from six-jet A. Cycle valve strainer clogged. page 14). wave seat *NOTE: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath dealer.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Need help?
Do you have a question about the Platinum Series and is the answer not in the manual?
Questions and answers