Directed Electronics SmartStart 5000-series Owner's Manual page 36

Programming System Features
Note: When doing any programming with security features off, the horn function
(feature menu 1 item 13) must be programmed as Siren function to get an audible
confirmation from the unit.
The System Features Learn Routine dictates how the unit operates. It is possible to
access and change most of the feature settings using the control center button.
1. Open a door.
2. Turn the ignition on, then off.
3. Select a Menu. Press and hold the control center button. The number of siren
chirps indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu
2 and 3 chirps for menu 3.
4. When the desired menu chirps are heard, release the control center button.
5. Select a Feature. Press and release the control center button the number of
times corresponding to the feature you wish to change. Then press and hold
one more time to select the features.
6. Program the Feature. While holding the Control center button, you can
program the feature using the remote control.
For features with only two options; = option 1 while = option 2.
For features with more than two options; selects the options in ascending order.
Once a feature is programmed:
• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete
To access another feature in the same menu:
1. Press and release the control center button the number of times necessary to
advance from the feature you just programmed to the next one you want to
program.
Then press the control center button once more and hold it.
2.
To select another menu:
1. Press and hold the control center button.
2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi-
cating which menu has been accessed.
The learn routine exits if any of the following occurs:
• The open door is closed
• The ignition is turned On
• There is no activity for 30 seconds
• The control center button is pressed too many times
Security Features Disable/Enable
The system has the ability to function as a security/remote start system or keyless/re-
mote start system by enabling or disabling security. The default setting is Enabled.
To program the feature.
1. Open a door.
2. Turn the ignition on, then off.
3. Press and hold the control center button until the LED flashes 3 times and the
siren (if connected) chirps 3 times.
4. Release the control center button.
Note: If the control center button is released and then pressed again, the sys-
tem will enter the features programming menus.
5. Within 15 seconds, simultaneously press the and buttons of a pro-
grammed remote control.
6. The siren (if connected) will chirp and the parking lights will flash as listed
below
1 flash/chirp: Security features disabled
2 flashes/chirps: Security features enabled
Security Features Disabled will disable all security operations of the system, includ-
ing but not limited to those listed below:
• Multi Level Arming
• Sensor Warn-away
© 2010 Directed Electronics. All rights Reserved.
• Full Trigger Operation
• Armed While Driving
• Automatic Engine Disable
Note: Disabled features with programmable options can still be programmed manu-
ally or with the Bitwriter but will not operate until the Security Features have been
enabled.
The Security Features Disable/enable routine exits if the following occurs:
• The open door is closed
• The ignition is turned on
• There is no activity for 15 seconds
• The control center button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or un-
locked. If the learn routine has previously been locked, it must be unlocked
with Bitwriter® - this cannot be done manually with the control center but-
ton.
The Bitwriter® gives you access to a wider range of system options. These
features and the adjustments that may be programmed are described in the table
below.
Menu Feature Default Options
Item
1 Siren Duration 30 sec. 1-180 sec.
2 Aux 2 Timed Output 30 sec. 1-90 sec.
3 Aux 3 Timed Output 30 sec. 1-90 sec.
4 Aux 4 Timed Output 30 sec. 1-90 sec.
5 Engine Runtime 12 min. 1-60 min.
6 Diesel Start Delay 15 sec. 1-90 sec.
7 Timer Mode Runtime 12 min. 1-16 min.
8 Virtual Tach Fine Tune Not initialized 0-1000 in 50 millisecond increments
9 Transmitter Programming Unlocked Locked
10 Feature Programming Unlocked Locked
Note: The "Zap" feature on the Bitwriter does not reset the Virtual tach or security
features enabled/disabled settings
Feature Menus
Default settings are in bold type.
Menu 1 - Basic
Menu Two-chirp setting
One-chirp setting
Item
1 Active Arming Passive arming
2 Arm/disarm chirps on Arm/disarm chirps Off
3 Ignition lock On Ignition lock Off
4 Ignition unlock On Ignition unlock Off
5 Active locking only Passive locking
6 Panic with ignition On No panic with ignition On
7 0.8 second door lock pulses (1) 3.5 (2), 0.4 (3) seconds
8 Forced passive arming on Forced passive arming off
9 Automatic engine disable on Automatic engine disable off
10 Armed When Driving (AWD) On AWD Off
11 Code Hopping On Code Hopping off
12 Horn Output Pulsed Constant
13 Horn function Full Alarm Only (1) Siren function - chirp length
20ms (2), 30ms (3), 40ms (4), 50ms (5)
14 Comfort Closure ON (1) Comfort Closure OFF (2)
Comfort Closure 2 (3)
Menu 2 - Advanced
Menu Two-chirp setting
One-chirp setting
Item
30 second siren duration
1 60 second siren duration
2 Nuisance Prevention Circuitry On Nuisance Prevention Circuitry OFF
Progressive door trigger
3 Instant door trigger
4 Disarm from Valet, 1 pulse Disarm from Valet, 2-5 pulses
Door trigger error chirp ON
5 Door trigger error chirp OFF
6 Ignition controlled domelight On Ignition controlled domelight OFF
Unlock output 1 pulse
7 Unlock output 2 pulses
8 Lock output 1 pulse Lock output 2 pulses
Factory disarm with trunk release
9 Factory disarm with trunk release OFF
ON
10 FAD function with Unlock (1) Before Unlock (2), Remote Start only (3)
11 FAD 1 pulse 2 pulses
12 AUX 2 validity (1) Latched (2), Latch reset with ignition
(3), 30-secs timed (4), 60-secs (5),
90-secs (6)
13 AUX 2 Linking None (1) Arm (2), Disarm (3), Remote Start (4)
14 AUX 3 validity (1) Latched (2), Latch reset with ignition
(3), 30-sec. timed (4)60sec(5)90sec(6)
15 AUX 3 linking None (1) Arm (2), Disarm (3), Remote Start (4)
16 AUX 4 validity (1) Latched (2), Latch reset with ignition (3),
30-sec. timed (4) 60sec (5) 90 (6)
17 AUX 4 linking None (1) Arm (2).Disarm (3), Remote Start (4)
Menu 3 - Remote start
Menu Two-chirp setting
One-chirp setting
Item
1 Engine checking: Virtual Tach Voltage(2), OFF(3), Tachometer(4)
2 Remote start runtime: 12 min 24 min, 60 min
3 Constant
Parking light output: Flashing
4 Cranking time: 0.6 sec 0.8, 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, 4.0
second
5 Activation pulse 1 2
2nd Ignition/Acc output: Ignition Accessory
6
7 Acc state during wait-to-start Off On
8 2nd status output: Normal Rear defogger: latch 10 min.
rear defogger pulse
Anti grind: On
9 Off
10 Diesel timer: Wait-to-Start input Timed 15 , 30 ,45 seconds
Timer mode run time: 12 min
11 3, 6, 9, min
12 Timer mode: Timed starts Temp starts
13 Short run (turbo): 1 min
3,5, 10 min
Remote Programming
1. Open a door
2. Turn key to the ON position
3. Within 5 seconds, press and release the control center button one time.
4. Within 5 seconds, press and hold the control center button. The LED will flash
one time and the siren chirps to confirm entry into remote programing.
5. Press the button on the remote control.
6. The siren will chirp to confirm the remote has been programmed.
7. Release the control center button.
8. The siren will emit one long chirp confirming that remote programming has
been exited.
The programming routine exits if any of the following occurs:
The open door is closed
The ignition is turned off
There is no activity for 30 seconds
The control center button is pressed too many times
Basic Remote Functions
Button Function
ARM
DISARM
REMOTE START
AUX TRUNK RELEASE
Note: See Owner's guide for more details
Long Term Event History
The system stores the last two full triggers in memory. These are not erasable. Each
time the unit sees a full trigger, the older of the two triggers in memory is replaced by
the new trigger. To access long term event history:
1. With the ignition Off, press and hold the control center button.
2. Turn the ignition On.
3. Release the control center button.
Within 5 seconds, press and release the control center button. The LED flashes
4.
in groups indicating the last two zones that triggered the unit for 1 minute or
until the ignition is turned off. Refer to table of zones.
Note: The Warn Away triggers are not stored to memory and is not reported.
Table of Zones
A zone is represented by the number of LED flashes used by the system to identify a
particular type of input.
Trigger Type
Zone Input Description
Instant Trigger BLUE (H1/7)
1
Multiplexed Shock Sensor Input Mux BLUE sensor port wire.
2
Door Trigger GREEN (H1/8) and VIOLET (H1/6).
3
Multiplexed Shock Sensor Input Mux GREEN wire
4
Ignition Yellow ribbon harness wire
5
Hood Trigger GRAY on the 6-pin shutdown harness
6
QRNDSS5003 2010-10
2