Advertisement
Quick Links
F u j i t s u C o m p u t e r S y s t e m s
Charge-Only Cradle
User's Guide
FPCCR05
I N S T R U C T I O N S
The charge-only cradle is designed for a desktop, counter
top, or wall-mounted installation where a quick connection
to a DC power source is needed. The Tablet PC can be
placed in the charge-only cradle and used while external DC
power is supplied to the cradle. The connector pins on the
cradle are "high-usage" type pins and are designed to with-
stand a large number of insertions and removals. The cradle
includes two adapters that fit over the Tablet PC's DC-in
port to make it more suitable for the high-usage environ-
ment.
The cradle can accommodate a Tablet PC with a standard
main battery or an optional high-capacity battery. A remov-
able spacer is included with the cradle to make the cradle
usable with either battery.
Advertisement
Related Manuals for Fujitsu FPCCR05
Summary of Contents for Fujitsu FPCCR05
- Page 1 F u j i t s u C o m p u t e r S y s t e m s Charge-Only Cradle User’s Guide FPCCR05 I N S T R U C T I O N S The charge-only cradle is designed for a desktop, counter top, or wall-mounted installation where a quick connection to a DC power source is needed.
- Page 2 Installing the System in the Cradle To install the Tablet PC in the charge-only cradle, you must first attach a DC adapter to the system’s DC port. Attaching the DC Adapter Hold your system so that the left side (when viewed in portrait mode) with the DC-in port is facing you (Figure 1).
- Page 3 Verifying Battery Size Determine whether your Tablet PC has a standard main battery or an optional high-capacity main battery installed. If your Tablet PC has a high-capacity main battery installed, remove the spacer (Figure 2) that is located inside the cradle on the right. Pull it upwards to remove it from the slot.
- Page 4 Installing the Tablet PC in the Charge-Only Cradle Place the cradle on the flat, stable location in which it will be used After verifying that the spacer is configured correctly and the DC adapter is attached to the DC-in port, hold the system in landscape mode, with the buttons arranged across the top (Figure 3).
- Page 5 DC-In Port Figure 4. DC-In Port on Cradle Removing the Tablet PC from the Charge-Only Cradle While holding the base of the cradle with one hand, gently pull the Tablet PC out of the cradle. Mounting the Cradle on a Wall The charge-only cradle is designed so that it can be easily mounted to a wall.
- Page 6 Cradle Section Separation Point Base Section Figure 5. Separating the Cradle 2. Once disengaged, store the base section in a safe place for future use. 3. The back of the cradle section has four holes for wall- mounting and six holes for reattaching the base section. Wall-mount Holes Base Attachment Holes (6 total) Figure 6.
- Page 7 Attach four screws (sheet metal, #14 panhead, zinc- plated recommended, or equivalent) to the wall as shown in Figure 7. The screw heads should extend from the wall approximately 0.25”. 12.25" (311.0 mm) 4.26" (108.0 mm) Figure 7. Wall-mount Screw Dimensions Align the wall-mount holes on the cradle (Figure 6) with the mounting screws so that the screw heads extend into the round portions of the wall-mount...
- Page 8 1-800-8Fujitsu (1-800-838-5487) or e-mail us at: 8fujitsu@us.fujitsu.com Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu, Ltd. All other trademarks mentioned herein are the property of their respective owners. We cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions or future changes.