Picture In Picture (Pip) - Hitachi 53UWX10BA Operating Manual

PICTURE-IN-PICTURE (PIP)
Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature
allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The
Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).
ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The highlighted channel display will
move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main picture. When
the lower channel display is highlighted, channel tuning is for the PIP sub-picture.
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV
program while viewing other programs from the ANT A source or any of the video inputs.
Models: 61UWX10BA, 53UWX10BA,
43UWX10B
ANT A
TO
CONVERTER
ANT B
AUDIO TO HI-FI
R L
Back of
VCR
V L R
OUTPUT
VCR
Hitachi Model or
Similar Model
Models: 61SWX10B, 61SWX12B
53SWX10B, 53SWX12B
OPTICAL COAXIAL
INPUT INPUT
ANT A
TO
REAR SPEAKER CONVERTER
L
ANT B
R
SUB
AUDIO TO HI-FI
WOOFER
R L
Back of
VCR
V L R
OUTPUT
VCR
Hitachi Model or
Similar Model
Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:2,
V:3, V:4, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A,
V:2, V:3, V:4, or V:5).
PIP button
Press the PIP button and a sub-picture will appear in one of the three different modes (SINGLE, SPLIT or SURF), depending on
the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.
SINGLE MODE PIP
Press the PIP button and a sub-picture appears in one of the three different modes (SINGLE, SPLIT or SURF), depending on the
last selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to
select between main and sub-picture tuning control (indicated by gray highlighted channel display.) Press the VID1, VID2, VID3,
VID4 or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3,
VIDEO:4 and VIDEO:5 and ANT:A source. (ANT B source cannot be viewed as a sub-picture.)
PIP
NOTES: 1. When using Y-P B P R input, only 480i signal can be viewed as a single mode PIP.
2. When ANT B is selected as the main channel, the SWAP feature is disabled.
3. Only sound from the main picture can be heard.
4. In SINGLE PIP mode, thumb stick CURSOR
S-VIDEO S-VIDEO S-VIDEO
VIDEO VIDEO Y/VIDEO Y/VIDEO VIDEO
(MONO) (MONO) P (MONO) P (MONO)
B B
L L L L L
P P
R R
R R R
R R
AUDIO AUDIO AUDIO AUDIO
AUDIO
MONITOR
INPUT 1 INPUT 2 INPUT 4 INPUT 5
OUT
STOP
CONNECT ONLY 8 OHM SPEAKERS
DO NOT SHORT CIRCUIT
THESE TERMINALS
(Such damage is NOT COVERED
by your television warranty)
S-VIDEO S-VIDEO S-VIDEO
VIDEO
VIDEO VIDEO Y/VIDEO Y/VIDEO
(MONO) (MONO) P (MONO) P (MONO)
B B
L L L L L
P P
R R
R R R R
R
AUDIO AUDIO AUDIO AUDIO AUDIO
MONITOR
INPUT 1 INPUT 2 INPUT 4 INPUT 5
OUT
Ant A 10
Use Thumb Stick
to move PIP inset.
Ant A 12
Main Picture
PIP
Sub Picture
, will move the sub picutre up/down.
27
SELECT
VOL CH
INFO
VID 3
PIP PIP CH FREEZE
,
PIP ACCESS
SWAP
PIP MODE
TV/VCR
PROG SLOW
REC
Ant A 10