Advertisement
Flash Beam™
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
Flash Beam™
•
Keep the outside of this device dry at all times. Do not spill water
or other liquids into or on to your unit. To prevent fire or shock
hazard, do not expose this product to rain or moisture.
•
Be sure to save the packing carton in the event you may have to
return the unit for service.
•
This unit is designed for interior use only. Do not use this unit out
doors. Use of product outdoors will void the warranty.
•
Be sure that the local power outlet match that of the required vol-
tage for your unit.
•
Do not attempt to operate this unit if the power cord has been
frayed or broken.
•
Always route your power cord out of the way of foot traffic.
•
Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in the rare case of an internal short.
•
Disconnect the unit's main power when left unused for long peri-
ods of time.
•
Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6" (15cm) between this device and a wall.
•
Never block the ventilation holes.
•
Do not attempt to operate this unit, if it becomes damaged in any
way.
•
Never operate this unit when it's cover is removed.
•
This unit is for adult use only. Keep out of the reach of children.
Flash Beam™
This fixture is fitted with halogen lamps which are highly suscep-
tible to damage if improperly handled. Never touch lamp with your
bare fingers as the oil from your hands will shorten lamp life. Also,
never move the fixture until the lamps have had ample time to cool.
Remember, lamps are not covered under warranty conditions.
American DJ Supply
- www.americandj.com - Flash Beam™ Instruction Manual Page 3
©
®
General Instructions
Precautions
Halogen Lamp Warning
Flash Beam™
Introduction: Thank you for purchasing the Flash Beam™ by
American DJ
. For your convenience the Flash Beam™ has been
®
lamped and is ready to be used, there is no assembly necessary.
This unit includes a hanging bracket and may be hung or set on a flat
surface. For best results, use a fog or haze machine to enhance the
beam output. Please read the following instructions before installing
or operating your new Flash Beam. ™
Operating Instructions: Plug the unit in to a matching power outlet
or into a power pack. Light output will be immediate when the unit is
powered on. The unit must receive a sound source to operate nor-
mally. If there is no sound source the beams of light will not bounce
up and down. You can adjust the sound senstivity by turning the knob
located on the rear of the unit.
Mounting: When used with included mounting bracket, this unit may
be mounted in any safe position or set on a flat stable surface.
Caution! Be sure not to obstruct cooling vents and keep this unit in a
well ventilated area. Never open the unit while in use. Avoid touching
the lamps, the lamp will get extremely hot under normal usage and
may cause serious injury.
Flash Beam™
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging your
unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.E. smoke, fog residue, dust, dew).
American DJ Supply
- www.americandj.com - Flash Beam™ Instruction Manual Page 4
©
®
Operation
Cleaning
Advertisement
