Table of Contents
Advertisement
RyoB l. g[],F"il.".fl
r"t F $l i]19,,
Ir A N uA L
SPECIFICATIONS
Wheel diameter
14"
I nput
120 Vol t s AC, 15 A mps , 3 HP
Wheel speed
33 00 RPM (nomi nal)
Wheel
Reinforced wheels
14" x 1/ 8" x 1"
Vise angle
0 - 45 degrees
Max. cutting dimensions
P i p e
Angle steel
Metal siding
Net weight
5" (outside diameter)
6-1 12" W x 3-5/1 6" H
B -1l1 6" W x 2-511 6" H
45. 3 rb
THANK YOU FOR BUYING A RYOBI CUT-OFF MACHINE
Your new cut-off machine has been engineered and manufactured
to Ryobi's high standard for dependabil-
ity, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free
performance.
Caution: Carefully read through this entire owner's manual before using your new cut-off
machine. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. lf you
use your cut-off machine properly and only for what it is intended, you will enjoy years of
safe, reliable service.
Please fill out and return the Warranty Service Registration Card so we can be of future service to you.
Thank you again for buying RyobiTools.
'Save
4980356
Advertisement
Table of Contents
Related Manuals for Ryobi C-356 TYPE III
Summary of Contents for Ryobi C-356 TYPE III
- Page 1 B -1l1 6" W x 2-511 6" H Net weight 45. 3 rb THANK YOU FOR BUYING A RYOBI CUT-OFF MACHINE Your new cut-off machine has been engineered and manufactured to Ryobi's high standard for dependabil- ity, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
-
Page 2: Sy M Bolm Ean In G
Servicing requires extreme care and knowledge and should be performed only by a qualified seruice technician. For service we suggest you return the tool to your nearest Ryobi Factory Service Center or Authorized Seruice Organization for repair. When servicing, use only identical Ryobi replacement parts. -
Page 3: Rules For Safe Operation
RULES FOR SAFE OPERATION READ ALL INSTRUCTIONS KNOW YOUR POWER TOOL Safe operation of this power tool requires that you read and understand this owner's manual and all labels affixed to the tool. Learn its applications and limitations as well as the potential hazards peculiar to a cut-off machine. - Page 4 Ryobi Authorized Service Center. 27. ALWAYS TURN SWITCH OFF before disconnecting it to avoid accidentalstarting. 28. ALL REPAIRS, WHETHER ELECTRICAL OR MECHANICAL, should be made at a Ryobi Authorized Service Center. Use only Ryobi replacement parts. 29' SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 5: Extension Cords
CUT-OFF MACHINE SAFETY 1. MAKE SURE THE CUT-OFF WHEEL lS SECURELY MOUNTED as described in the operating instructions before connecting the toolto a power supply, Do not tighten wheel excessively, since this can cause cracks. Z. CHECK WHEEL FOR FISSURES AND CRACKS, and test for normal operation prior to use. g. -
Page 6: Electrical Connection
ELECTRICAL CONNECTION Your Ryobi cut-off machine is powered by a precision built Ryobi electric motor. lt should be connected only toapowersourcethatsatisfiesthepowerinputlistedonthetool'snameplates. lfthenameplateismarked 1ZOV, AC, or 60H2, the tool must be operated only with alternating currerit (normal household current). Never operate the tool on direct (DC) or current that is lower or higher than the specified voltage. - Page 7 U NPAC KING Caref u lly remove all parts f rom the shipping carton. WARNING: Never operate the tool in Do not discard the packing materials until you the locked-down position. The transport have identified all the parls using the Loose Parts chain is used only for transporting or storing the tool.
- Page 8 ASSEMBLY Your Ryobi cut-off machine comes fulfy assembled. Abrasive Wheel WARNING: Do not connect machine to p owe r s ou rce u n ti l a s s e m b ly is cornplete. Failureto comply could resuft in acci den ta f st a rti n g a n d p o s s ib le Outer serious injury.
-
Page 9: Wheel Installation
WHEEL INSTALLATION from the power source. 1. Be sure the tool is disconnected 2. Inspect the replacement wheel for defects such as cracks. chipping, and correct speed rating. lf defects are found or the speed rating is not greater than 3300 rpm, discard the wheel and select another. 3. -
Page 10: Cutting Angle Adjustm Ent
ADJUSTIVI ENTS ADJ USTAB LE STATIONARY VISE The adjustable stationary vise is located at the rear of your cut-off machine. This vise can be rotated to attain cutting angles from 0 to 45 and moved rearward to allow greater cutting widths. Adjustable WARN ING: A l wa ys u n p lu g th e m a c h in e Stationary... - Page 11 QUIC K L OC K-RE LE ASE VI SE Your cut-off machine is equipped with a quick lock- release vise system as standard equipment. With this featu re you are able to open and close the vise quickly without repetitive turning of the vise crank handle. US IN G T H E QU ICK LOCK.
-
Page 12: Power Supply
OPERATING POWER SUPPLY Before operating your,cut-off machine, check your power supply and make sure it meets the requirements listed on the nameplate. A substantial voltage drop will cause a loss of power and machine overheating. Co mm on cause s o f p o we r l o s s a n d m a c h in e overheating are insufficient extension cord size and multiple tools operating from the same power source. -
Page 13: Maintenance
, r epl a c e them . It is recommended that at least once a year you take the tool to a Ryobi Factory Service Center or Ryobi Authorized Service Center for a thorough cleaning and F i gur e 13 !ubr!cat!on. -
Page 14: Part Description
Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center or Ryobi Factory Service Center. Be sure to provide all pertinent facts when you call or visit.
Need help?
Do you have a question about the C-356 TYPE III and is the answer not in the manual?
Questions and answers