Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Diamond Digital Diamond Digital DV201B
Summary of Contents for Diamond Digital Diamond Digital DV201B
- Page 1 Diamond Digital DV201B Colour TFT LCD Monitor 20.1” (51 cm) LCD Panel Size...
- Page 2 Copyright 2004, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic,...
-
Page 3: Table Of Contents
Table of Contents Important Safety Instructions ..........1 Features................2 3 Unpacking the Monitor .............3 4 Hardware Installation ............5 5 Windows driver installation ..........7 6 Setting the Display Resolution ........8 Choosing the Best Resolution...........8 Supported Graphics Modes and Refresh Rate Selection..9 7 Adjusting the Monitor.............12 User Controls ..............12 Adjusting the Monitor's Display ........13 OSD Function Menu ............13... -
Page 4: Reference Information
Diamond Digital is a registered trademark of Mitsubishi Electric Australia Pty. Ltd. Microsoft and Windows are registered trademarks of Microsoft Corporation. -
Page 5: Important Safety Instructions
Important Safety Instructions Please read the following safety instructions before installing or cleaning your Diamond Digital monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. -
Page 6: Features
(typical) ♦ High Contrast Ratio – 600:1 (typical) ♦ True Colour Display With 16.7M (8 bit) colour, the Diamond Digital DV201B monitor offers you better image quality. ♦ High Quality Ratiometric Expansion With any resolution within the monitor’s specified range, your Diamond Digital DV201B monitor can expand the image to full screen. -
Page 7: Unpacking The Monitor
Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately LCD monitor User’s Manual VGA Cable DVI-D Cable... -
Page 8: Power Cord
Power Cord AC Adapter Audio Cable Locate the model name and the serial number label on the back of your monitor, and write the details of the monitor and your place of purchase in the space on page (ii) of this manual for future reference. -
Page 9: Hardware Installation
Hardware Installation Connecting the Monitor Base Remove the base from the packing box and place it on the desk. Next, remove the LCD display and carefully seat it on the base. (See fig.1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. - Page 10 Connecting the Display to your Computer Using the VGA cable Power off your computer. Connect one end of the VGA signal cable to the LCD Monitor’s VGA port. (See Fig 1-3) Connect the other end of the signal cable to the VGA port on your PC.
- Page 11 Instructions for VESA Mounting To detach the LCD Monitor from its stand, unscrew the two screws for the monitor stand and pull it downwards to remove, then unscrew the four screws for the monitor stand bracket and pull this down to remove. Figure 1-6 Interface for Arm Applications Before installing the mounting device, please refer to...
-
Page 12: Windows Driver Installation
Windows driver Installation The DV201B is fully Windows Plug and Play compatible so no specific Windows drivers are required for installation. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add New Hardware wizard. Just follow the prompts to load the native Plug and Play drivers. -
Page 13: Setting The Display Resolution
Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as the maximum resolution that may be displayed on the LCD. In the case of the DV201B the LCD resolution is 1600 x 1200 pixels. This is also known as the “native”... -
Page 14: Supported Graphics Modes And Refresh Rate Selection
If you are using an Apple Macintosh, change the resolution by doing the following: MacOS 8.x/9.x Click the Apple icon at the top, left corner of the screen, select Control Panel and then select Monitors. Select a resolution of 1600 x 1200 pixels with between 60Hz and 75Hz refresh rate. - Page 15 able to support these modes. For the native resolution of 1600 x 1200 pixels, for example, refresh rates of 60, 70 and 75 Hertz are supported. With Windows 95, 98, ME, 2000 or XP you can change the refresh rate of the graphics signal as follows: 1.
-
Page 16: Standard Timing Table
Table 1 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. Resolution Horzontal Vertical Dot Clock Remark Frequency Frequency Frequency (kHz) (Hz) (MHz) 640x350 31.469 70.087 25.175 640x400 24.83... -
Page 17: Adjusting The Monitor
Adjusting the Monitor User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 Stereo Speakers PC Audio Stereo output. Speaker Volume Use to adjust the speaker volume (clockwise to increase, Control anti-clockwise to decrease). Power Switch Turns the display on and off. -
Page 18: Adjusting The Monitor's Display
External The monitor speakers will be disabled when using an Headphone Jack external headphone or external speakers. Adjusting the Monitor's Display OSD Function Menu To access the OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. -
Page 19: Picture Optimisation
Adjusts the sampling frequency for the Analogue (VGA) to Digital signal Clock conversion (Not available when using DVI). This function lets you select a colour temperature. Using the Adjustment Colour Control buttons to select the required colour temperature. Please see the diagram below for function and description. -
Page 20: Manual Picture Adjustment
The monitor will remember the settings obtained by the auto calibration settings and use them whenever you turn the monitor on. Note that you may need to readjust the monitor if it is connected to a different computer or if the computer’s graphics adaptor is replaced. - Page 21 Please Note: You must use one of the factory modes when manually adjusting the picture. If you are having difficulties generating a supported mode, ask your computer dealer or the distributor or manufacturer of your graphics card for assistance. The procedures described in this chapter should be performed for every resolution and type of graphics signal that you wish to use.
-
Page 22: Frequently Asked Questions
Check that the cable is securely connected to the computer. Check the VGA signal cable for damage. If any pins are bent or broken off, ♦ contact your dealer or an authorised Mitsubishi Electric service agent (see Chapter 10 for details). - Page 23 No image is displayed, what can I do? Check that the light (LED) next to the monitor’s power button is lit and is ♦ green in colour. If the LED is green, press one of the Function Select buttons on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Setting the Display Resolution and reset the graphics card to one of the monitor’s supported graphics signals.
-
Page 24: Specifications
Specifications Diamond Digital DV201B Model: Display Characteristics Display Type 20.1“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 51 cm / 20.1” Native (Maximum) Resolution 1600 x 1200 pixels Colours 16.7 million (8bpp) Contrast Ratio 600:1 (typical) Brightness 250 cd/m²... - Page 25 Input Signal Line Frequency 24 – 80kHz multi-frequency Image Frequency (Refresh Rate) 49 - 75Hz Video Signal RGB analogue (Positive polarity) 0.7 Vpp/75 Ohm Synchronization TTL separate, composite TTL Signal Connection 15-pin mini D-sub and 24 pin DVI-D connectors Physical Characteristics Power Management VESA DPMS, Energy Star Maximum Power Consumption...
-
Page 26: Service Contacts
If problems remain after checking this manual, please contact your place of purchase or contact: Australian Service Contacts Visit the Customer Support section of Mitsubishi Electric Australia’s web site at www.mitsubishielectric.com.au for details of your nearest Mitsubishi Electric Authorized Service Center or... -
Page 27: New Zealand
Victoria and Tasmania 4 / 303 Burwood Hwy East Burwood, VIC, 3151 Telephone: (03) 9262-9899 Fax: (03) 9262-9850 Western Australia 5 / 329 Collier Road Bassendean, WA, 6054 Telephone: (08) 9377-3411 Fax: (08) 9377-3499 New Zealand Contact: BDT New Zealand Ltd. 1 Parliament St.