Related Manuals for Teledex E SERIES
Summary of Contents for Teledex E SERIES
- Page 1 E SERIES VoIP USER GUIDE For E100IP, E100IPLBY, E100IPTRM, E200IP, E200IPTRM, E103IP, E103IP RediDock, E203IP, E203IP RediDock...
-
Page 2: Important Safety Instructions
2. This device must accept any interference work is required. Opening or removing received, including interference that may covers may expose you to dangerous cause undesired operation. www.teledex.com E SERIES VoIP USER GUIDE... - Page 3 The termination on an interface may consist operate the equipment. E SERIES VoIP USER GUIDE www.teledex.com...
- Page 4 Any changes made by the user not approved by service may be required. But if advance notice is the manufacturer can void the user’s authority to not practical, the telephone company will notify operate the telephone. www.teledex.com E SERIES VoIP USER GUIDE...
-
Page 5: Technical Specifications
With handset: 2.0 lbs. repair or warranty information, please contact POWER ADAPTER Teledex at (800) 462-9446. If the equipment is causing harm to the telephone network, the 7.5VDC 300mA Adapter (for cordless HDKIT) telephone company may request that you disconnect 9 VDC 300mA (Pass through adapter for cordless the equipment until the problem is resolved. -
Page 6: Table Of Contents
3.8.1 Account Manage ....26 2. Handset Keys for E Series ....13 3.8.2 Syslog Configuration . -
Page 7: E100Ip And E100Iptrm Phone Map
(Press Menu, then 21. Redial key press the numbers to be dialed, and finally 22. Speaker—half duplex end by pressing the speed dial key.) 23. Wall mount bracket 10. Paper faceplate/Plastic overlay 24. Desk mount bracket E SERIES VoIP USER GUIDE www.teledex.com... -
Page 8: E103Ip And E103Ip Redidock Phone Map
18. RJ-45 WAN (POE) input for power and 34. Charging leads (base) network connection 35. Speaker—half duplex (base) 19. LED charging indicator 36. Wall mount bracket 20. RJ-45 LAN input for guest connectivity 37. Desk mount bracket www.teledex.com E SERIES VoIP USER GUIDE... -
Page 9: E200Ip And E200Iptrm Phone Map
26. Speaker—half duplex end by pressing the speed dial key.) 27. Wall mount bracket 11. Paper faceplate/Plastic overlay 28. Desk mount bracket 12. Enter key (submerged) E SERIES VoIP USER GUIDE www.teledex.com... -
Page 10: E203Ip And E203Ip Redidock Phone Map
35. Redial key (base) indicator (base) 36. Charging leads (base) 20. RJ-45 LAN input for guest connectivity 37. Speaker—half duplex (base) 21. Paper faceplate/Plastic overlay 38. Wall mount bracket 22. Phone case 39. Desk mount bracket www.teledex.com E SERIES VoIP USER GUIDE... -
Page 11: Functions
Detection) dialing) • Telnet: Remote login protocol • Speed-dial • DNS: Domain Name Server • Call-forward, Three-way conference call (in • TFTP: Trivial File Transfer Protocol select 2-line models) • Caller ID display • DND (Do Not Disturb), Black List, Limit List • Auto-answer • Program settings through a standard web browser • Remote management functionality via Telnet • Classification management for common user’s password and superuser’s password E SERIES VoIP USER GUIDE www.teledex.com... -
Page 12: Introduction
1. Introduction Voice Quality • VAD: Voice Activity Detection • CNG: Comfortable Noise Generator This is the User Guide for the E Series VoIP phone. • LEC: Line Echo Canceller This phone is a standard SIP (Session Initiation • Packet Loss Compensation Protocol) phone, and some configuration is • Adaptive Jitter Buffer necessary before it is ready for use. This manual... -
Page 13: Handset Keys For E Series
Redial the last number dialed. M1–M7 On-Hook 7 speed dial 2.1.5 SPEED DIAL KEYS numbers The E Series phone has 7 speed dial keys Dialing “1” programmable through the Web UI under Dialing “2” Advanced -> Memory Key. Dialing “3”... -
Page 14: Web Browser User Interface To Configure The Phone
– Enable Static The Current Status page shows the working state – Set E Series’ IP address in the IP Address field of the VoIP phone. The network part shows the – Set the Subnet mask in the Netmask field connection state of the WAN interface and the –... -
Page 15: Lan Configuration
The DHCP server If there is a DHCP server in your local network, configuration won’t take effect until you reboot the E Series phone will automatically obtain the the device. WAN port network information from your DHCP NAT: Enable Network Address Translation (NAT) server. - Page 16 Translation (NAT) is the process of modifying IP Domain Realm: SIP domain—enter the SIP address information in IP packet headers while domain if any. Otherwise, the E Series phone will in transit across a traffic routing device. Keep use the proxy server address as the SIP domain.
- Page 17 Auto TCP: Applicable Hospitality unchecked. environments. The default is unchecked/disabled. Auto TCP refers to TCP Auto-tuning. TCP tuning Signal Encode: Not applicable in Hospitality techniques adjust the network congestion environments. The default is unchecked. E SERIES VoIP USER GUIDE www.teledex.com...
-
Page 18: Advance
DNS: Default DNS (Domain Name Server) of the lease table. DNS Relay: Enables the Domain Name Server The purpose of a DMZ is to add an additional relay function. layer of security to an organization’s Local Area www.teledex.com E SERIES VoIP USER GUIDE... -
Page 19: Stun Configuration
Local SIP Port: The SIP port of this phone. Access List Supports Two Type Limits: The input_access limit or output_access limit. Each Load: Load the choices of the SIP line. type supports 10 items maximum. E SERIES VoIP USER GUIDE www.teledex.com... -
Page 20: Vlan Configuration Qos Configuration
3.5.6 VLAN CONFIGURATION/QOS E Series firewall filter is the base WAN port. So CONFIGURATION the source address or input destination address should be the WAN port IP address. The E Series phones implement Virtual LANs and Quality of Service (QoS) within this section FIREWALL CONFIGURATION of the menu. -
Page 21: Digital Map Configuration
A digital map is based on rules judging when the ALWAYS SET TO “Undifferentiated” in the drop down user stops dialing and when to send the string of numbers to the server. E Series phones support menu. the following digital map:... -
Page 22: Call Service
ELEMENTS IN A DIAL PLAN PATTERN: Hot Line: Configures the hotline number. If this option is set, E Series immediately dials this Matches any dialed digit, #, or * number when the handset is picked up, or the 0–9, *, #... -
Page 23: Memory Key Programming
P equals a 1-second pause, so PPP equals and Retrieve numbers (70 and 71) are a 3-second pause, then the digits 12345 are sent. arbitrary, and subject to the programmer of the PBX. They are used here as an example only. E SERIES VoIP USER GUIDE www.teledex.com... -
Page 24: Mmi Filter
Ring Volume: The volume of the alerting ring as heard by the called party. The MMI filter is used limit access to the E Series G729 Payload Length: G729 payload length. phone. When an MMI filter is enabled, only the G.729 is an audio data compression algorithm for... -
Page 25: Update Firmware
(.z) file or the configuration file. file xxx.3300IP.txt), then click on the “Update” Config Encrypt Key: The encryption key of the button. After the upgrade, the E Series phone will confirmation file. automatically restart. Protocol Type: The protocol type used for FTP Update: Upload or download the configuration upgrading. -
Page 26: System Manage
Set the Web access account or keypad password the User Interface (UI). Some functions may be for the E Series phone. inappropriate for hospitality environments, or not show up in a phone without a screen, but useful in commercial applications or display sets. -
Page 27: Mmi Configuration
3.8.5 MMI CONFIGURATION * * 4(I) 7(P) #. Set the greeting information on the LCD display Input the IP address of the E Series phone in the through the Man-Machine-Interface (MMI). browser, press the Enter key, and then you can visit the settings layout of the E Series phone. -
Page 28: Sip Configuration
CONFIGURE STATIC IP – Choose Static – Fill in the IP address of the E Series phone in Server Address: This is the IP address or FQDN the Static IP Address field – Fill in the subnet mask in Netmask (Fully Qualified Domain Name) of the IP/PBX SIP Registration server. -
Page 29: Reference-Quick Keys
It might come from the configuration file, option 66, option 125, or option 43. Re-Program New ConfigID— The Teledex family of SIP phones has implemented **77*password*ConfigID# (**RP*xxx*yyyy#) an innovative way to determine various states of Description: After entering **77*, the user must... -
Page 30: Reference-Sip Quick Start To Register
Lastly, cycle power (remove firmware version of the phone is circled in red. and replace WAN power cable) to restart the phone with factory default settings. Program Your Connection Under the VoIP -> SIP Configuration Screen www.teledex.com E SERIES VoIP USER GUIDE... -
Page 31: Reference-Ip Dect Handset/Base Autosync
AutoSync Handset Registration Handsets can be registered most simply by performing AutoSync, which is to place the handset into the cradle and the pairing will happen automatically. E SERIES VoIP USER GUIDE www.teledex.com... - Page 32 Toll Free: +1.800.462.9446 Tel: +1.719.638.8821 Email: info@teledex.com www.teledex.com © 2013 Cetis, Inc. Product specifications and descriptions in this document subject to change without notice. Cetis , Teledex , TeleMatrix , Scitec , ExpressNet , and ® ® ® ® Teledex iPhone are trademarks or registered trademarks of Cetis, Inc.
Need help?
Do you have a question about the E SERIES and is the answer not in the manual?
Questions and answers