Remote Control; Placing The Television In Standby Mode - Samsung CS-29Z40 Owner's Instructions Manual

Remote Control

(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
1 1 POWER 3 3 -/--
Used to switch the TV Used to select a channel
on and off. numbered ten or over.
Press this button, then
2 2 Numeric buttons
"--" symbol is
Used to select channels
displayed. Enter the
directly.
two-digit channel
number.
4 4 $ $ P
/ /
Used to increase or
Used to display the next
decrease the volume.
or previous stored
5 5 MENU channel.
% % EXIT
Used to display the on-
screen menu or return to
Used to exit from any
the previous menu.
display or return to
normal viewing.
6 6 ... ... / † † / œ œ / √ √
^ ^ MUTE
Used to control the
cursor in the menu.
Used to switch the
sound off temporarily. To
7 7 S.MENU
turn the sound back on,
Used to display the
press the MUTE,
sound menu.
button.
8 8 TURBO
& & ENTER
Used to select the turbo
While using the on-
sound option.
screen menus, press the
9 9 P.SIZE
ENTER button to
Used to change the
activate (or change) a
screen size.
particular item.
0 0 DUAL I-II
* * S.MODE
Used to select the
Used to select the
sound mode.
sound effect.
! ! SOURCE
( ( P.MODE
Used to display all of the
Used to select the
available video sources.
picture effect.
@ @ INFO
) ) TV
Used to view the
Used to return to the TV
channel information and
mode when it is in
setting status you
external input mode.
selected.
a a SLEEP
# # PRE-CH
Used to select a preset
Used to switch
time interval for
repeatedly between the
automatic turn off.
last two channels
displayed.
Installing Batteries
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not
operate normally, check that the "+"
and "-" ends of the batteries are inserted correctly or the
batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
English - 2
Switching the Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the " I " button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
, or
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to "Channel - Auto Store" or "Channel - Manual
Store" on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
"Setup - Plug & Play" on page 3.
4 To switch the television off, press the " I " button (On/Off)
on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the " I "
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.