Advertisement
P L e A S e R e A d A N d S AV e T H e S e
I M P O RTA N T S A F e T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
electric shock or fire, or damage the heater.
should always be followed to reduce the risk of fire,
11. To prevent a possible fire, do not block air intakes or
electric shock, and injury to persons, including the
exhaust in any manner. Do not use on soft surfaces,
following:
like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside.
1. Read all instructions before using this heater.
Do not use it in areas where gasoline, paint, or
2. This heater is hot when in use. To avoid burns, do not
flammable liquids are used or stored.
let bare skin touch hot surfaces. If provided, use
13. Use this heater only as described in this manual. Any
handles when moving this heater. Keep combustible
other use not recommended by the manufacturer
materials, such as furniture, pillows, bedding, papers,
may cause fire, electric shock, or injury to persons.
clothes, and curtains at least 3 feet (0.9 m) from the
14. Always plug heaters directly into a wall outlet/
front of the heater and keep them away from the
receptacle. Never use with an extension cord or
sides and rear.
relocatable power tap (outlet/power strip).
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
15. When unplugging, be sure to pull by the plug and
the heater is left operating and unattended.
not the cord.
4. Always unplug heater when not in use.
16. If the heater will not operate, see specific instructions
on Auto Safety Shut-off.
5. Do not operate any heater with a damaged cord or
17. DO NOT attempt to repair or adjust any electrical or
plug or after the heater malfunctions, has been
mechanical functions on this unit. Doing so will void
dropped or damaged in any manner. Discard heater,
your warranty. The inside of the unit contains no user
or return to authorized service facility for
serviceable parts. All servicing should be performed
examination and/or repair.
by qualified personnel only.
6. Do not use outdoors.
18. Discontinue use if plug or outlet is hot. It is
7. This heater is not intended for use in bathrooms,
recommended that the outlet be replaced if plug or
laundry areas and similar indoor locations. Never
outlet is hot to touch.
locate heater where it may fall into a bathtub or
19. The heater must not be located immediately below a
other water container.
socket-outlet. Do not use this heater in the
8. Do not run cord under carpeting. Do not cover cord
immediate surroundings of a bath, a shower or a
with throw rugs, runners, or similar coverings. Do not
swimming pool.
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
9. To disconnect heater, turn controls to off, then
remove plug from outlet.
10. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
THIS APPLIANCe HAS A POLARIzed PLUG (one blade is
wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
dO NOT ATTeMPT TO MOdIFY THIS PLUG OR deFeAT THIS
SAFeTY FeATURe IN ANY WAY.
BH1520_12EM1.idml 2
deSCRIPTIONS
Figure 1
1
1. Left End Cap
2. Rear Housing
3. Right End Cap
4. Control Panel
5. Grill
TeCHNICAL SPeCIFICATIONS
• Wattage: 1500W/ (+ 5% – 10%)
• Working Voltage: 120V AC/60 HZ
PRe-OPeRATING INSTRUCTIONS
SAVe THeSe
1. Carefully remove your heater from the box.
2. Check package for additional parts if unit is
INSTRUCTIONS
not shipped already assembled.
3. Place the heater on a firm, level surface.
4. Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
TURNING THe UNIT ON/OFF ANd
SeTTING THe THeRMOSTAT
1. Plug unit into wall socket.
2. Press (mode) button:
• 1st = LO; runs continuously on Low.
• 2nd = HI; runs continuously on High.
F e AT U R e S - O P e R AT I O N S
(See FIG.1 & 2)
Figure 2
2
3
4
1. Display
2 Mode Indicator Lights
3. Mode Button/Adjustment
4. Thermostat Adjustment
5
• 3rd = Auto Low (AL); press (+) or (-)
to set desired temperature.
6
6. Base
• 4th = Auto HI (AH); press (+) or (-)
7. Base Mount
to set desired temperature.
8. Wall Mounting Bracket
3. Once you have selected the mode and temperature,
(not shown)
the display returns to the current room temperature
and gradually increases as the room warms.
4. If you selected an Auto mode and the heater does not
start, make sure the set temperature is higher than the
current room temperature.
5. To turn the unit off, keep pressing the mode button (3) until
all mode indicator lights (2) are not illuminated. (Figure 2)
SeTTING THe ON TIMeR
1. With the heater off, press and hold (+) and (-)
simultaneously until display flashes "0".
2. Press (+) or (-) to select the amount of time you
would like to pass before the heater turns on.
3. After setting the timer, the display shows a red dot
next to the current room temperature on the display
to indicate that the timer is activated.
4. After the programmed length of time has passed, the
heater automatically turns on Auto HI at 75°F for 2
hours.
SeTTING THe OFF TIMeR
1. Select the desired mode and/or temperature.
2. With the heater running, press and hold (+) and (-)
F e AT U R e S - O P e R AT I O N S
simultaneously until the display flashed.
particular wall.
3. Press (+) or (-) to select the amount of time
1. Remove Base (6) from the bottom of the Base Mount (7).
you would like the heater to run.
4. After setting the timer, the display shows a RED dot
2. Remove Base Mount from the bottom of the Grill (5)
1
next to current room temperature on the display to
indicate that the timer is activated.
3. Secure the Wall Mounting Bracket (8) to the wall.
2
5. The heater automatically shuts off after the
4. Hang the Heater Unit on the Mounting Bracket using
programmed length of time has passed.
3
FrostProtect
™
Press the (mode) button 5 consecutive times for FrostProtect
AUTO SAFeTY SHUT-OFF
4
setting (AF will show in the digital display). This mode will
This heater is equipped with a technologically-advanced,
activate your heater when the surrounding area reaches near
safety system that automatically shuts off power to the
freezing temperatures and will cycle ON and OFF in HI power
heater when a potential overheat temperature is reached.
to maintain a temperature between 40-48°F.
The heater can only resume operation when you reset it.
Reset the Heater
WALL MOUNTING ASSeMbLY
(See FIG. 3–6)
If the unit shuts down:
IMPORTANT: Before drilling into any wall ensure no
1. Unplug the heater and wait 30 minutes.
electrical cables are present in the area.
2. Plug in and turn on.
NOTe: Due to the multitude of potential mounting surfaces,
Tip-Over Shut-Off
mounting screws are not included with this product. Please
If the heater is knocked over, it will instantly shut off.
seek professional assistance or visit your local hardware
To reset, simply place the heater in an upright position
store to determine which type of screw is best for your
and turn ON the heater.
Figure 3
7
6
Figure 5
8
5. Grill
6. Base
7. Base Mount
Refer to Figure 3.
by removing the two securing screws. Refer to Figure 4.
Refer to Figure 5.
the hooks located on the back of the unit.
Figure 4
5
7
Figure 6
8. Wall Mounting Bracket
3/24/12 1:57 AM
Advertisement
