Advertisement
resting lightly against your skin, use motions
how To Use
towards edge of beard line to trim the beard line
to desired location in facial area and away from
beard in neck area.
Trimming Beards
To Thin and Taper the Beard
■
Before you begin, comb your hair in the direction that it
■ Trimmer guard attachment is off.
grows so that the hairs are at their maximum height and
■ Use a small comb to comb and hold the beard
facing in the same direction.
hairs in place while trimming.
■
Determine how much hair you want to cut and position the
■ Holding the trimmer horizontally with the cutting
hair length selector accordingly. Remember, until you are
unit facing away from you, move the trimmer
familiar with using the trimmer, it's always better to select
along the length of the comb.
a longer hair setting initially in order not to trim too much
Creating the "Stubble Look"
hair.
■ Trimmer guard attachment should be on and set
■
Turn the unit's power switch to ON, and begin trimming.
to position 1 (0 mm) or 2 (2.5 mm).
■
Beard, mustache, or sideburn hairs should be dry. Avoid
■ Hold trimmer horizontally with the cutting unit fac
using lotions before using your trimmer.
ing either up or down.
■
When finished trimming, turn the unit's power switch
■ Trim hairs using an upward or downward motion against or
to OFF.
with the direction of hair growth, whichever is preferred.
To Trim the Beard's hair Length
■ For an even closer "stubble look," remove the hair length
selector attachment and repeat the previous two
■ Trimmer guard attachment is on.
steps. However, caution must be taken not to
■ Turn the trimmer so the front of the cutting unit is facing
away from you.
remove too much hair, creating a "blotchy" look.
■ Start trimming under your chin and, following your jaw
To Trim Mustache and Sideburns
bone line, work toward your ear and upper
Without trimmer guard attachment
beard line using an upward motion. Allow the
■ Remove trimmer guard attachment.
hair length selector attachment to follow the
■ Place a finger on upper lip only to lift hair up, away from
contours of your face. You may trim either
skin.
against or with the direction of beard growth,
■ Trim hairs using an upward motion.
whichever is preferred.
■ After achieving desired length, use a downward motion to
To Define the Beard Line
blend mustache hairs.
■ Remove trimmer guard attachment.
NOTE: Use slow and light pressure. Too much pres-
■ Hold trimmer vertically with trimmer cutting blades facing
sure may trim off more hair than desired.
you.
■ Turn trimmer off.
■ Start with edge of beard line, and with the cutting blades
To trim sideburns
with a soft brush. Clean your trimmer regularly to ensure that
■ Comb sideburns following the direction of your hair growth.
the unit's operating life is not prematurely shortened.
■ Do not apply pressure or hard objects to the cutters.
■ Be certain trimmer guard attachment is ON.
■ Hold trimmer vertically with front of rimmer facing you.
■ Do not use liquid cleaners on the cutters or harsh or corro
■ Trim sideburns using a downward motion.
sive chemicals on the unit's main body.
Weekly
■ Turn trimmer OFF.
■ Trimmer should always be shut off.
Trimming the Nape of Your Neck
■ Remove trimmer guard attachment from
■ You will need a hand mirror for this operation if performing it
trimmer. Shake or blow out any accumulated
alone. The mirror is not necessary if trimming is performed by a
hairs.
second person.
Main trimmer
■ Remove the hair length selector attachment.
1. Flip the blades open by pushing upward on the cutter teeth.
■ Use your fingers to lift the hair at the base of your head up
The cutter assembly will swing up and the underside of the cut-
off the neck. Your index finger should be covering the roots
ter assembly will be accessible.
of the hairs you are lifting to prevent accidental removal by t
2. Blow out any loose hair that has accumulated.
rimmer.
Brush out any remaining hair from the cutter teeth
■ Using your other hand, hold the trimmer horizontally to the
and hair pocket with the brush provided. To access
base of your neck with the cutting unit facing up, and move
brush, remove trimmer guard attachment. Slide brush
the trimmer along the length of the neck until the
upward.
unit touches your finger covering the hair roots at
■ Do not rinse the cutter assembly under water or
the base of your head. Repeat this procedure for
use cleaning fluids, which could remove the
the entire area of the neck. Be sure to move the
lubrication
unit slowly when performing this operation and to
Troubleshooting
keep the hair roots at the base of your head out of the way
The trimmer does not work when turned on:
of the trimmer.
■ Be certain batteries have been properly installed. Trimmer
■ Use the hand mirror to inspect the results of the operation
will not operate unless batteries are correctly positioned.
and ensure all hairs along the nape of the neck have been
■ If battery power has been depleted, replace with 2 "AA"
trimmed.
alkaline batteries (see Battery section).
Trimmer cutters do not move:
Cleaning & Maintenance
■ The cutting unit may be dirty and clogged. Clean the unit as
directed in the Cleaning & Maintenance section.
NOTE: This appliance does not contain any user-serviceable
Cleaning and Maintaining Your Trimmer
parts.
Your trimmer is fitted with high-quality hardened steel blades
that are permanently lubricated. Cleaning should only be done
SPECTRUM BRANDS, INC. SHALL NOT BE RESPONSIBLE
Performance Guarantee
FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT. ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
Limited Two-Year Warranty
IM PLIED WARRANTIES OF FITNESS AND MERCHANTABILITY,
ARE LIMITED IN DURATION TO TWO YEARS FROM DATE OF
Spectrum Brands, Inc. is a global consumer products com-
ORIGINAL PURCHASE.
pany with a diverse portfolio of world-class brands, including
Remington -branded electric shavers. Spectrum Brands, Inc.
This warranty gives you specific legal rights and you may also
warrants this product against any defects that are due to
have other rights which vary from state to state or province to
faulty material or workmanship for a two-year period from the
province. Some states do not allow the exclusion or limitation
original date of consumer purchase. This warranty does not
of incidental, special or consequential damages.
include damage to the product resulting from accident or
Spectrum Brands, Inc. Money-back Offer
misuse.
If within 30 days after you have purchased your Remington ®
If the product should become defective within the warranty
branded product, you are not satisfied and would like a refund,
period, we will replace it free of charge. Return your product
return it with the sales slip indicating purchase price and
and sales receipt with your name, address and day time phone
date of purchase to the retailer from whom it was purchased.
number to: Remington Returns Center, 507 Stokely Dr., P.O.
Spectrum Brands, Inc. will reimburse all retailers who accept
Box 1, Deforest, WI 53532. For more information call 800-736-
the product within 30 days from the date of purchase. If you
4648 in the US or 800-268-0425 in Canada.
have any questions concerning the money-back guarantee,
please call 800-736-4648 in the US or 800-268-0425 in
KEEP ORIGINAL SALES RECEIPT AS PROOF OF PURCHASE
Canada.
FOR WARRANTY PURPOSES.
Questions or comments:
This warranty does not cover products damaged by the following:
Call 800-736-4648 in the US or 800-268-0425 in Canada.
■ Accident, misuse, abuse or alteration of the product
or visit www.RemingtonProducts.com
■ Servicing by unauthorized persons
Dist. by: Spectrum Brands, Inc.
■ Use with unauthorized accessories
Madison, WI 53711
■ Any other conditions beyond our control
Dist. by: Spectrum Brands Canada, Inc.
Mississauga, ON L5L 0A1
No responsibility, obligation, or liability is assumed for the instal-
lation or maintenance of this product.
® Registered Trademark of ROVCAL, INC.
©2010 ROVCAL, INC.
03/10 Job# CS38166
Designed in USA
Manufactured to Remington's specifications in the PRC.
T22-29259
Advertisement
