Table of Contents
Advertisement
Quick Links
Matrox Piranha Switch 8
8 Port 10BaseT Ethernet Switch
SAE8
Installation Guide 10496-MT-0102
Matrox
PIRANHA
1
2
The Matrox Piranha Switch 8 is an 8 port 10BaseT Ethernet switch. The Piranha
Switch is a full segment switch, yet is affordable enough to be used instead of a
repeater hub. Devices connected to the Piranha Switch can communicate with
each other at full wire speed, achieving aggregate throughput 800% faster than
devices connected to the ports of a repeater hub.
Each of the 8 ports on the Piranha Switch can be configured for half or full-duplex
operation, allowing you to double the connection speed for devices that are able
to operate in full-duplex mode. Each port can be connected to a server,
workstation, another switch, or to a repeater hub connected to multiple Ethernet
devices. The Piranha Switch is capable of supporting up to 8192 MAC addresses.
A
Before You Begin
Verify the contents of your package. It should contain the following items:
•
Matrox Piranha Switch 8
• Power adapter
• Power adapter cord
• Registration card
• This guide
If any of these items are missing, contact your Matrox Networks representative.
NOTE:
B
Configuring Ports for Half or Full-duplex
Operation
Many Ethernet devices, including newer Network Interface Cards (NICs) and
most switches, are capable of full-duplex operation. If possible, you should
configure a device and Piranha Switch port to which it connects for full-duplex
operation. Repeater hubs and older NICs are only capable of half-duplex
operation.
10 BaseT Ethernet Switch
MDI-X
RJ-45
PORTS
3
4
5
6
Status LEDs
7
8
Advertisement
Table of Contents
Summary of Contents for Matrox SAE8
-
Page 1: Before You Begin
The Matrox Piranha Switch 8 is an 8 port 10BaseT Ethernet switch. The Piranha Switch is a full segment switch, yet is affordable enough to be used instead of a repeater hub. Devices connected to the Piranha Switch can communicate with each other at full wire speed, achieving aggregate throughput 800% faster than devices connected to the ports of a repeater hub. - Page 2 In order to configure a port for full-duplex operation, perform the following steps: 1. Ensure that the Piranha Switch is not connected to its power adapter. If it is, unplug it. 2. Using a Phillips (star) screwdriver, carefully remove the 2 screws on the top of the case, and the two screws on the back of the case.
-
Page 3: Supported Media
8192 MAC addresses. Supported Media You can connect a device to a port of the Piranha Switch using Category 3 or Category 5 Unshielded Twisted-Pair (UTP) wiring. The wire must have an RJ-45 Ethernet plug in order to connect to a port of the Piranha Switch. -
Page 4: Troubleshooting
Workstation connection to the server (via Piranha Switch) slow and/or erratic. OLUTION One or more ports of the Piranha Switch are incorrectly configured for half or full-duplex operation. Refer to the instructions contained in section B to determine whether ports should be configured for half or full-duplex mode, to match the configuration of the devices to which they are connected. -
Page 5: Obtaining Technical Support
The device may require a cross-over or straight-through wire in order to connect to a port on the Piranha Switch. Refer to the instructions contained in section C to determine which kind of wire to use in order to connect a specific type of device. -
Page 6: Regulatory Compliance
• Physical dimensions: Height Depth Width Weight • Operating temperature: 0°C - 50°C ambient • Storage temperature: -25°C - 65°C • AC input power: 100-240 VAC, 50-60 Hz single phase universal input • Input current: 2.0 A MAX @ 5 VDC •... - Page 7 Reglement sur le brouillage radioélectrique édicté par Industrie Canada. Matrox is a registered trademark. Matrox Piranha, Matrox Networks and Matrox Shark are trademarks of Matrox Electronic Systems Ltd. All other trademarks are the property of their respective owners. Matrox reserves the right to change specifications without notice.