Gemini series User Manual Packing List The complete Gemini 15 / 17 / 19 / 19” wide-screen package consists of: One 1U 19” rack mount console Two rails with front and rear bracket Two blockers. One 1.8 m KVM cable. (HDDB-15 / VGA + PS/2 x 2) ...
14. Never open the equipment. For safety reason, qualified service personnel should only open the equipment. 15. If one of the following situations arises, get the equipment checked by service personnel. The Power Cord or plug is damaged. ...
Page 4
Gemini series User Manual The equipment has dropped and damaged. If the equipment has obvious signs or breakage. ...
8 / 16 / 32 ports console to serve your customer well. 3. Keep low inventory: From the 3 models of consoles and 17 models of KVM switches, you can create total 54 models in Gemini Series. It is the best solution for inventory control.
With the patented extension bracket, the console body can extend 13cm. Even there is big server handle or patch panel above the console, our Gemini console can have over 90 degrees viewing angle. ( compared with 4~5 cm from our...
To access the main menu. This button also acts as Menu the “Enter” button. Table 2-1. Panel Controls Figure 2-1. Gemini 15 / 17 OSD Control Bar Figure 2-2. Gemini 19 OSD Control Bar 2.1 Auto Tune Press the “auto tune” button. The panel will adjust the display size...
Gemini series User Manual 2.2 Input Source 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the“menu”button to enter,and you will see: VGA / DVI 4.
Gemini series User Manual 2.4 Contrast 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 1. Press the “menu” button to enter. 2. Use the “Down” and “Up” button to adjust the contrast of the display.
Gemini series User Manual 3. Press the “menu” button to enter. And you will see: Icon Description 9300°K To set CIE coordinates at 9300°K color 7500°K To set CIE coordinates at 7500°K color 6500°K To set CIE coordinates at 6500°K color...
Gemini series User Manual 4. Use the “Down” and “Up” button to scroll. 5. Press the “menu” button to enter. 2.7 Language 1. Press the “menu” button. 2. Use the “Down” and “Up” button to scroll. Auto tune. Input Source...
Gemini series User Manual Exit 3. Press the “menu” button to enter, and you will see: Yes/ No 4. Select “Yes” button then ‘Menu” button to recall the factory setting. Select “No “ to return to the previous page. 2.9 Exit Press the “exit”...
2. Before installation, make sure all peripherals and computer have been turned off. 3. The cabinet depth range must be in 570 ~ 870 mm for 15” and 17” console (650 ~ 950 mm for 19” console). Contact your dealer for deeper cabinet application.
Gemini series User Manual 5. Key x 2 3.1.3 Install Console Step 1. Adjust rail with rear bracket to fit your cabinet 2. Install front and rear bracket on cabinet. 3. Repeat step 1~2 for the other side. 4. Push console into rails and push it to the end.
Gemini series User Manual 5. Install a screw to combine blocker and console. (Both sides) blocker 6. Install three screws (length = 6 mm) in rear of the console (Both sides) to finish the installation. 3.2 Install Modular KVM Switch Step 3.2.1 Hardware Kits Contents...
Gemini series User Manual 3.2.2 Install Modular KVM Switch Step 1. Install two screws (length = 6 mm) to combine bracket and KVM switch. (Both sides) 2. Push KVM switch into the rails from rear of cabinet. plastic rail of KVM switch rear view of rail 3.
Gemini series User Manual Installing the Video Card and Video Driver Before connecting the LCD console, make sure your computer has a video card already installed for the monitor. After you connect the console, install the video software driver. The video driver is supplied by the video card manufacturer and may be found on the CD-ROM that came with your computer.
Gemini series User’s Manual 3.3.2 Connecting the Console To connect an LCD console to a computer, perform the following steps 2 3 4 5 6 7 1. KVM dock (Only for Mercury / Mars / Venus 5. PS/2 mouse series KVM Switch ues.) 6.
Gemini series User’s Manual Testing the Console To test that the console is working properly, perform the following steps: 1. Power up the console, and then turn on your computer. 2. Make sure the video image is centered within the screen area. Use the OSD controls to adjust the image (see note below) or press the Auto button on the right hand side of the monitor.