ABLE OF ONTENTS 1. Before You Begin ............................3 What is included .............................. 3 Unpacking Instructions ............................ 3 AC Power ................................ 3 Contact Us ..............................3 Safety Instructions ............................4 2. Introduction ............................... 5 Features ................................5 DMX Channel Summary ..........................5 Product Overview ............................
Warning! All fixtures must be connected to circuits with a suitable Earth Ground. Contact Us W o r l d W i d e General Information CHAUVET® 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560...
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET® at: 954-929-1115. LEDsplash™ 152B User Manual 3/9/2010 3:02 PM...
2. I NTRODUCTION Features 6-channel DMX-512 LED wash light Blackout/static/dimmer/strobe Selector switch for sound active or automatic programs Static colors and RGB color mixing with or without DMX controller Built-in automated programs via master/slave or DMX Built-in sound activated programs via master/slave or DMX A d d i t i o n a l F e a t u r e s Linkable with LED Shadow™, LED Shadow™...
Maximum recommended number of fixtures on a serial data link: 32 Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
C AB L E CO N N ECT O R S Cabling must have a male XLR connector on one end and a female XLR connector on the other end. Resistance 120 DMX connector configuration ohm ¼ W between pin 2 (DMX -) and pin 3 (DMX +) of COMMON the last fixture.
Master/Slave Fixture Linking 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector.
4. O PERATING NSTRUCTIONS Operation Stand-Alone Mode (Sound-Active, Auto Mode): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. Set dipswitches position to Sound Active or Auto Mode. Mode Dipswitches Sound Active...
DMX Mode A working DMX-512 signal source plugged into the LEDsplash™ 152B activates the DMX mode. DMX Channel Values NOTE! Please read all instructions carefully on fixture DMX control mode and addressing. DMX channels 2, 3, 4, 5 and 6 functions are determined by the current settings of channel 1. For example, while Channel 1 is set between 000 and 029 the following conditions will apply;...
S ET T ING T H E DM X S T AR T I NG AD D R E S S This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address.
DM X Q U IC K R EF E RE NC E CH ART DMX Address Quick Reference Chart Dip Switch Position DMX DIP #9 0 0 0 SWITCH SET 0=OFF #8 0 0 0 1=ON #7 0 0 1 X=OFF or ON #6 0 1 0 #1 #2 #3 #4 #5...
power the fixture and it will automatically enter into this mode If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page. LEDsplash™ 152B User Manual 3/9/2010 3:02 PM...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #). Products returned without an RMA # will be refused. Call CHAUVET® and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
Need help?
Do you have a question about the LEDsplash 152B and is the answer not in the manual?
Questions and answers